Silicon Image Fedora Red Hat Series Driver Installation (SATA 3114 Controller) OVERVIEW This driver disk adds support for the SiI 3114 SATA controller that is otherwise not supported by the open source installation program. Supported versions: * Fedora Core 2, Kernel revision 2.6.5-1.358. * This driver rev. 1.0.5.9 supports 32-bit AMD/Intel platforms for Sii3114 controller with RAID, and hot-plug capabilities. CREATE FLOPPY before INSTALLATION A floppy disk is required to install into a brand new (or blank) disk drive. 1. Several Options: . If you received a zip file, Use Winzip to unzip the [distribution]filename.zip file on to a formatted floppy disk. . If you received a tgz file, extract the contents of the [distribution]_sii____rhdd.tgz file on to a formatted floppy disk. (e.g. use tar xzf [distribution]_sii____rdhh.tgz) . If you received a img file, and you are running windows: use "rawrite.exe sii____.img A:" (you can get rawrite from RedHat installation disk #1 \dosutils directory) If you are running linux: use "dd if=filename.img of=/dev/fd0" Note: IMPORTANT NOTE FOR OEM CUSTOMERS ADD your PCI ID to the "pcitable" file if OEM VendorId is going to be different from SiI 0x1095 IDs. (End Users should ignore this step) 2. The following BIOS BOOT sequence is recommended => CD, Hard Disk, Floppy INSTALL THE Fedora DRIVER Before you start make sure the BIOS sees your adapter card (if applicable) and your disk drives. Installing the Fedora SiI Driver currently requires some manual intervention. It also requires to disable probing so that the Open Source Drivers does not get installed. At boot time type: 'linux noprobe' at the boot prompt. If just adding Data Drives or upgrading go to sections 2.1 or 2.2 (non-bootable SATA drives are considered Data Drives) Boot from the Fedora CD 1 or a boot diskette that you have created. When you get to the screen shown in figure 1. get a shell prompt (see last page) and execute the initial_install script as follows: # mkdir /f # mount /dev/fd0 /f # cd /f # ./initial_install.sh figure 1: | Warning | No hard drives have been found. You probably need to manually choose device drivers for the for the installation to succeed. Would you like to select drivers now? | Yes | | No | Once the driver is installed select 'No' and then 'Done' on the next screen. Continue with the installation. Last, BEFORE REBOOTING run the script below. # ./upgrade_driver.sh This last step writes all the drivers permanently into the kernel. Installation at this point is completed. 2.1 Adding a DATA DRIVE If your system is already up and running then you can use execute shell scripts to modify the kernel or add loadable modules to access the SATA drives as follows: . # mount /mnt/floppy in case of DOS formatted floppy . # mount -t vfat /dev/fd0 /mnt/floppy . # 'sh /mnt/floppy/load-driver-from-floppy.sh' (DATA DRIVES) (or use the the proper script depending on your kernel) . if you want to make sure you can see the drives, you may want to 'mke2fs /dev/sda' and 'mount /dev/sda /test' the hard disk(s). (Depending on your system configuration, the SATA drives could be /dev/sdb, /dev/sdc, /dev/sdd.....) . insmod sii3114. As an example add the following lines at the end of the script in /etc/rc.d/rc.sysinit 'insmod scsi_mod' 'insmod sii3114' . At this point you are done with the installation 2.2 Upgrading the Kernel If your system is already up and running then you can use execute shell scripts to modify the kernel or add loadable modules to access the SATA drives. 3. GENERAL INFO . If you cat /proc/scsi/sii3114/* you should see the Driver as reported by the kernel. . If you cat /proc/scsi/scsi you should see the your DRIVE TYPE as reported by the kernel. 4. New Features and bug fixes a. The driver could support SATA ATAPI devices. b. This revision of driver has GUI interface that can configure RAID set. 5. Known Restriction Please note that ATAPI hot plug is not expected. Console Keystrokes Contents 1 [Ctrl]-[Alt]-[F1] installation dialog 2 [Ctrl]-[Alt]-[F2] shell prompt 3 [Ctrl]-[Alt]-[F3] install log (messages from installation program) 4 [Ctrl]-[Alt]-[F4] system-related messages 5 [Ctrl]-[Alt]-[F5] other messages 7 [Ctrl]-[Alt]-[F7] X graphical displayDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.