1. surecom.zip Driver
2. LSDOS.TXT File Contents

LSDOS.TXT Driver File Contents (surecom.zip)

*****************************************************************************
*									    *
*			SURECOM EP-312V Ethernet Adapter		    *
*									    *
*		   NDIS2 Driver for Lan Server DOS Workstations 	    *
*									    *
*****************************************************************************

Introduction:
=============

  The Ethernet NDIS2 Driver for Lan Requester DOS workstations confirms to the
  Network  Driver  Interface Specification(NDIS2). This document shows you how
  to setup the	driver	and  how  to use the enhanced functions by setting the
  custom keywords in configuration file.


Contents of the Subdirectory:
=============================

    EP312.DOS		The NDIS2 driver for Lan Requester DOS workstations.
    OEMSETUP.INF	The installation information file.
    LSDOS.TXT		This file.


Installation:
=============

  Before starting with the installation process, make sure that the adapter
  is properly installed and configured. You  can use the diagnostic program
  (A:\SETUP.EXE) to make sure your connection  with the network is correct.

  Installing driver procedure on DOS LAN Requester :
  -------------------------------------------------
      1) Install DOS Lan Requester to  HardDisk  with  " NO Network Adapter
	 Selected" option.

      2) Copy  EP312.DOS  from	your  Driver  diskette	to DOS LAN Services
	 subdirectory, like C:\NET .

      3) Under DOS LAN Requester subdirectory C:\NET, run INSTALL

      4) Move highlight to "The listed options are correct" item,then press
	 ENTER.

      5) Move highlight to "Network Card", then press ENTER.

      6) Select "Change driver for network card." item, then press ENTER.

      7) Select "Network card not shown in list below..", then press ENTER.

      8) Insert the PNP Ethernet driver diskette in floppy A,and specify the
	 pathname A:\LANSVR40.DOS,then press ENTER.

      9) PNP Ethernet NDIS2 driver is now installed on your computer, reboot
	 your computer.


  NOTE:
  -----
  Multiple Lan Adapters in a system:
      If you want to install mutiple Lan adapter in your system, you have to
      use the keyword, PNPID, in PROTOCOL.INI file to let driver locate  the
      right adapter. And you have to set DriverName to be EP312$ and EP3122$
      to distinguish from adapter 1 and adapter 2.  You can run A:\SETUP.EXE
      under DOS prompt to show all the	Ethernet addresses of your adapters.


Configuration Files:
====================

    Sample of configuration file:
    -----------------------------
    (Suppose the Lan Requester package is installed at C:\NET directory)

    File Name:		C:\CONFIG.SYS
    ----------
	DEVICE=C:\NET\PROTMAN.DOS /I:C:\NET
	DEVICE=C:\NET\DLSHELP.SYS
	DEVICE=C:\NET\EP312.DOS

    File Name:		C:\AUTOEXEC.BAT
    ----------
	SHARE
	C:\NET\NET START
	C:\NET\NET START PEER
	C:\NET\NET SHARE ZZZ=C:\

    File Name:		C:\NET\PROTOCOL.INI
    ----------
	...
	# The followings are Custom Keywords. Put the keywords to enable the
	# special functions.
	[MS$EP312]
	DriverName=EP312$
	IOBASE=0x300
	INTERRUPT=5
	EARLYRECEIVE=0
	EARLYTRANSMIT=0
	FULLDUPLEX=0

	# The following lines are for second adapter settings.
	[MS$EP312]
	DriverName=EP3122$
	IOBASE=0x320
	INTERRUPT=9
	EARLYRECEIVE=0
	EARLYTRANSMIT=0
	FULLDUPLEX=0

	[IBM$NETBEUI]
	DriverName=netbeui$
	SESSIONS=20
	NCBS=20
	BINDINGS=MS$EP312
	LANABASE=0
	...


    Custom Keywords:
    ----------------
	PNPID = hhhhhhhhhhhh	    This keyword is the Ethernet Address of
				    the adapter you want to drive. If there
				    are more than one ethernet	adapters in
				    your  system ,  you  have  to  use this
				    keyword to let driver locate  the right
				    adapter. However, you don't have to use
				    this  keyword  or  let the value  to be
				    zero (i.e. PNPID = 0) if  there is only
				    one adapter in your system.

	EARLYTRANSMIT		    This  keyword  is  used to enable turbo
				    transmission mode for accelerating data
				    transmission.

	EARLYRECEIVE		    This keyword  is  used  to enable turbo
				    receiption mode  for  accelerating data
				    receiption.

	FULLDUPLEX		    This  keyword is  used  to	enable full
				    duplex mode.


	Note:For PnP mode,the IOBASE and INTERRUPT keywords are ignored  in
	     your PROTOCOL.INI file.