1. Pro200B.zip Driver
2. LANMAN.TXT File Contents

LANMAN.TXT Driver File Contents (Pro200B.zip)

                     CNET PRO200 PCI Fast Ethernet Adapter
                                NDIS MAC Driver 
           for LAN Manager 2.x Workstation/Server Installation Guide
           =========================================================


Installation Procedure
======================

 1. Introduction
 ===============
    This document describes the procedure to setup LAN Manager 2.1
    Workstation/Server driver for the PCI Fast Ethernet Adapter.

 2. Location of Driver
 =====================
    (DOS) \NDIS20\DOS\DM9PCI.DOS
    (OS/2)\NDIS20\OS2\DM9PCI.OS2

 3. Sample Configuration Files
 =============================
    CONFIG.SYS (for DOS will contain) %%%
      DEVICE=C:\LANMAN.DOS\DRIVERS\PROTMAN\PROTMAN.DOS /I:C:\LANMAN.DOS
      DEVICE=C:\LANMAN.DOS\DRIVERS\ETHERNET\DM9PCI\DM9PCI.DOS

    CONFIG.SYS (for OS/2 will contain) %%%
      DEVICE=C:\LANMAN.OS2\DRIVERS\PROTMAN\PROTMAN.OS2 /I:C:\LANMAN.OS2
      DEVICE=C:\LANMAN.OS2\DRIVERS\ETHERNET\DM9PCI\DM9PCI.OS2

    PROTOCOL.INI (will contain) %%%
      [DM9PCI_NIF]
      ; PROTOCOL.INI SAMPLE

        DriverName = DM9PCI$
;
;       SLOT =  1
;          This parameter specifies the slot number used for notifications.
;          For PCI slot , you can specify from 1 to 16.
;
;       MEDIA_TYPE = AUTODETECT
;       MEDIA_TYPE = FM_100M_FULL
;       MEDIA_TYPE = FM_100M_HALF
;       MEDIA_TYPE = FM_10M_FULL
;       MEDIA_TYPE = FM_10M_HALF
;       Note:
;          AUTODETECT    ; --> Auto detect the data rate and duplex mode
;          FM_100M_FULL  ; --> Forced 100M Full Duplex Mode
;          FM_100M_HALF  ; --> Forced 100M Half Duplex Mode
;          FM_10M_FULL   ; --> Forced 10M Full Duplex Mode
;          FM_10M_HALF   ; --> Forced 10M Half Duplex Mode
;
;          This parameter specifies the connector type configuration
;          (data rate and duplex mode) of the  network adapter card.


 4. NDIS Driver Installation on LAN Manager v2.1
 ===============================================
    Before you start with the installation process, make sure that the adapter
    is properly installed and configured. Besides, make sure your Microsoft LAN
    Manager is properly installed too.

    a. Run the appropriate Microsoft LAN Manager of SETUP.EXE for computer you
       are setting up.(DOS, OS/2 or OS/2 Server). Select "Configuration" item
       since the adapter driver isn't included on the LAN Manager disk, insert
       the adapter driver diskette, select the item "PCI Fast Ethernet Adapter
       NDIS2 MAC Driver" and follow the directions.

    b. When completed, reboot your computer.


 5. NDIS Driver Installation on LAN Manager v2.2x
 ================================================

    a. Type setup in the LAN Manager directory and press <Enter>. The Microsoft
       LAN Manager Setup screen should appear.

    b. Choose "Network Drivers" from the "Configuration" field. Press <Enter>
       to confirm your choice.

    c. Choose <Add New Config> and press <Enter> to display a list of Network
       Adapter Drivers.

    d. Choose <Other Driver> and press <Enter>.

    e. Insert the Driver Diskette into drive A: or B: of your PC. Indicate the
       drive location A: or B: of the diskette and select <OK> to proceed.

    f. Select the appropriate Network Adapter Driver from the list.
       For example, select "CNET PRO200 PCI Fast Ethernet Adapter", Select <OK>
       to confirm your choice.

    g. Select an appropriate protocol. Use the <Space bar> to mark your choice.
       If you select TCP/IP protocol, you will be prompted to issue the IP
       address, the subnet mask, and the default gateway (router).
       By default, the workstation number of NetBIOS session is set to 6.
       Please consult Microsoft LAN Manager Installation Manual for more detail
       or check the online help.

    h. Select <OK> to confirm your choice.  A "Configuration Complete" message
       should appear on the screen.

    i. Save the configuration. Select <Save>.

    j. Press <F3> to exit.