1. 2200-101.zip Driver
2. WORKGRP.TXT File Contents

WORKGRP.TXT Driver File Contents (2200-101.zip)

FILE NAME: WORKGRP.TXT
======================

This file covers the installation procedures for the following networks:

    Microsoft Windows for Workgroups 3.1
    Microsoft Windows for Workgroups 3.11


*******************************************************************************
*  WINDOWS FOR WORKGROUPS 3.1
*******************************************************************************

The Ethernet PC card has been designed to be totally compatible with a
conventional NE2000 Ethernet board.  You can either use the NE2000 compatible
driver supplied on your Workgroup disk or Grey Cell's NE2NDIS driver.


INSTALLING WINDOWS FOR WORKGROUPS FOR THE FIRST TIME
====================================================

1.      Follow the Windows for Workgroups installation procedure.

2.      When the installation program asks for a Network adaptor, select 
	the "NE2000 compatible Adapter" and press RETURN.

	Alternatively, insert the Ethernet PC card drivers disk and select
	"Unlisted or Updated Network Adapter".  Indicate the sub-directory
	\NDIS on the drivers disk for the vendor file and you will see
	"Grey Cell Ethernet PC Card GCS2000" listed in the "Network
	Adapters" list.

3.      Select the interrupt number (IRQ) and base I/O port address. The
	default is 
		IRQ = 3
		IOBASE = 0x300
	Choose any available option but make sure the PC Card has the same
	configuration by using ECARD.

4.      Continue with the installation.

5.      When installation is complete, you may need to amend your CONFIG.SYS 
	to enable the PC card. Copy the file ECARD.EXE into the Windows 
	directory and add the line:
		   
		device=c:\windows\ecard.exe
    
	before the line "device=c:\windows\ne2000.dos".


IF YOU HAVE ALREADY INSTALLED WINDOWS FOR WORKGROUPS
====================================================

1.      Select Program Manager and start Control Panel

2.      Goto Step 2 above.


Note: If you are using an extended memory manager and the ECARD enabler, 
      you may need to explicitly exclude memory area D800-D8FF, or other 
      4 Kbyte memory space defined by the /MEM parameter.


*******************************************************************************
*  WINDOWS FOR WORKGROUPS 3.11
*******************************************************************************

The Ethernet PC card has been designed to be totally compatible with a
conventional NE2000 Ethernet board.  You can either use the NE2000 compatible
driver supplied on your Workgroup disk or Grey Cell's NE2NDIS driver.


INSTALLING WINDOWS FOR WORKGROUPS FOR THE FIRST TIME
====================================================

1.      Run ECARD.EXE.

2.      Follow the Windows for Workgroups installation procedure.

3.      The Windows setup software should be able to detect and install the
	correct driver for you.  If the automatic installation failed,
	follow the manual installation procedure below.

4.      When installation is complete, you may need to amend your 
	AUTOEXEC.BAT to enable the PC card. Copy the file ECARD.EXE 
	into the Windows directory and add the following line before 
	NET START:
		   
		ECARD
		NET START


WHEN YOU HAVE ALREADY INSTALLED WINDOWS FOR WORKGROUPS
======================================================

1.      Select Program Manager and run Network Setup from the Networks group.

2.      Select the Drivers option and select the "Add Adapters" button.  
	Highlight "NE2000 compatible Adapter" and press RETURN.

	Alternatively, insert the Ethernet card drivers disk and select
	"Unlisted or Updated Network Adapter".  Indicate the sub-directory
	\NDIS on the drivers disk for the vendor file and you will see
	"Grey Cell Ethernet Card GCS2000" listed in the "Network
	Adapters" list.

3.      Select the interrupt number (IRQ) and base I/O port address. The
	default is 
		IRQ = 3
		IOBASE = 0x300
	Choose any available option but make sure the PC card has the same
	configuration by using ECARD.

4.      To use the card, you will need to close Windows and reboot the PC.

4.      When installation is complete, you may need to amend your 
	AUTOEXEC.BAT to enable the PC card. Copy the file ECARD.EXE 
	into the Windows directory and add the following line before 
	NET START:

		ECARD
		NET START


Note: If you are using an extended memory manager and the ECARD enabler, 
      you may need to explicitly exclude memory area D800-D8FF, or other 
      4 Kbyte memory space defined by the /MEM parameter.