****************************************************************************
* *
* GREY CELL SYSTEMS 3400 Series Fax/Modem/Ethernet Card *
* NETWORKS.TXT Manual Supplement *
* (Driver Release 1.00) *
* Copyright (C) Grey Cell Systems 1996 *
* *
****************************************************************************
This document contains information that supplements the "3400 Series
User's Manual" for specific network operating systems.
Networks Covered Herein.
------------------------
Banyan Vines 4.0
DECnet Pathworks 4.0+
FTP Software PC/TCP Plus
IBM LAN Support Program
Microsoft LAN Manager
Novell Netware( Lite )
Novell Netware( v 2.x )
Novell Netware( v 3.x )
Novell Netware( v 4.x )
Windows for Workgroups 3.1
Windows for Workgroups 3.11
Windows 95
Windows NT
****************************************************************************
* NE2000 Network Drivers Supplied on The Installation Disk *
****************************************************************************
These drivers are to be used when using CARD2.EXE or CARD2CS.EXE.
ODI for DOS - NE2ODI.COM
( in sub-directory \NE2000\ODI )
NDIS Version 2.x for DOS - NE2NDIS.DOS
( in sub-directory \NE2000\NDIS2 )
Windows for Workgroups 3.11 - GCS3000.386
Enhanced Mode NDIS ( in sub-directory \WFW311 )
Packet Driver - NE2PD.COM
( in sub-directory \NE2000\PACKET )
Windows 95 Enhanced Mode NDIS - GCS3000.VXD
( in sub-directory \WIN95 )
Windows NT Enhanced Mode NDIS - GCS3000.SYS
( in sub-directory \WINNT )
****************************************************************************
* GCS3000 Network Drivers Supplied on The Installation Disk *
****************************************************************************
GCS3000.COM DOS/ODI Driver with direct enabler. Supports Intel
compatible, Compaq, IBM, Toshiba, Databook and PCI
controllers.
( in sub-directory \GCS3000\ODI)
GCS3000.DOS DOS Real Mode NDIS Driver with direct enabler. Supports
Intel compatible, Compaq, IBM, Toshiba, Databook and PCI
controllers.
( in sub-directory \GCS3000\NDIS2 )
****************************************************************************
* Network Driver Requirements *
****************************************************************************
Below is a table of network operating systems and the drivers required to
allow a network adaptor to work with them. If your network operating
system is not listed consult your vendor for driver requirements.
Drivers Required
Network Operating System NDIS2 ODI PD
3Com 3+ Open *
3Com 3+ Share *
AT&T StarGROUP v3.5 *
Artisoft LANTastic 5.0 *
(or LanBIOS driver for NE2000)
Banyan Vines 4.0 *
BW-NFS for DOS 3.0 * * *
DECnet Pathworks 4.0+ *
FTP Software PC/TCP Plus * * *
Hewlett Packard LAN Manager *
IBM LAN Support Program *
Microsoft LAN Manager *
NCSA Telnet *
Novell LAN WorkPlace for DOS *
Novell Netware( Lite ) *
Novell Netware( v 2.x ) *
Novell Netware( v 3.x ) *
Novell Netware( v 4.x ) *
Sun PC-NFS * *
Tenset Technologies Tenset/TCP *
Ungerman Bass LAN manager *
Windows for Workgroups 3.1 *
Windows for Workgroups 3.11 *1
Windows 95 *2
Windows NT *3
Wollongong PathWay Access * *
Wollongong WIN/TCP *
Notes:
1: We recommend using the NDIS Version 3.x driver (GCS3000.386) in
the sub-directory \WFW311.
2: You must use Windows 95 Enhanced Mode NDIS driver (GCS3000.VXD) in
the sub-directory \WIN95.
3: You must use Windows NT Enhanced Mode NDIS driver (GCS3000.SYS) in
the sub-directory \WINNT.
For ODI drivers use either NE2ODI.COM or GCS3000.COM. For NDIS drivers use
NE2NDIS.DOS or GCS3000.DOS.
****************************************************************************
* *
* Novell Netware Installation *
* for Grey Cell Systems 3400 Series Fax/Modem/Ethernet Card *
* *
****************************************************************************
Installation Procedures for (Version 2.1x 3.x):
Using GCS3000
or
NE2000 ( have to use CARD2.EXE or CARD2CS.EXE )
(1) Copy the following files from Novell's ODI Workstation Disk:
LSL.COM
IPXODI.COM
NETX.EXE or VLM.EXE and *.VLM
FOR GCS3000
(G2) Copy the following file from Grey Cell Series 3400 Installation Disk:
\GCS3000\ODI\GCS3000.COM
\GCS3000\ODI\NET.CFG
(G3) Modify the NET.CFG with any desired parameters
Link Driver GCS3000
INT n
PORT nnn
MEM nn000 (Note: use value as excluded in CONFIG.SYS)
COM n (Note: COM port disabled if unspecified)
(G4) Create a batch file or load the above drivers in the following
order:
LSL
GCS3000
IPXODI
NETX or VLM
FOR NE2000 ( have to use CARD2.EXE or CARD2CS.EXE )
(N2) Copy the following file from Grey Cell 3400 Series Installation Disk:
\NE2000\ODI\NE2ODI.COM
\NE2000\ODI\NET.CFG
(N3) Modify the NET.CFG with any desired parameters
Link Driver NE2ODI
INT n ( this should match CARD2/CS.EXE IRQ= )
PORT nnn ( this should match CARD2/CS.EXE IO= )
(N4) Create a batch file or load the above drivers in the following
order:
CARD2.EXE ( CARD2CS if using Card & Socket Services )
LSL
NE2ODI
IPXODI
NETX or VLM
(5) Log in to the network
Installation Procedures for (Version 4.x, and Personal Netware):
Using GCS3000
or
NE2000 ( have to use CARD2.EXE or CARD2CS.EXE )
(1) Insert Novell's installation disk into drive A:
(2) Run INSTALL.EXE, and follow the on-screen installation procedures
(3) Select and change "Primary Network Interface Card"
(4) Select "OEM Supplied Driver Files"
(5) Type in the path name A:\GCS3000\ODI and insert 3400 Series Installation
Disk into drive A:
(6) Select "Grey Cell 3400 Fax/Modem/Ethernet Card (w/ Enabler)"
(7) Select "Configure Primary Interface Card..."
(8) Setup the desired INT, PORT, MEM, COM value
(Note: use the value from step 4 for the MEM parameter)
(Note: COM port disabled if unspecified)
FOR NE2000 ( have to use CARD2.EXE or CARD2CS.EXE )
(N5) Type in the path name A:\NE2000\ODI and insert 3400 Series Installation
Disk into drive A:
(N6) Select "Grey Cell 3400 Fax/Modem/Ethernet Card (NE2000 Mode)"
(N7) Select "Configure Primary Interface Card..."
(N8) Setup the desired INT, PORT value ( int & io used by enabler)
(9) Follow the rest of Novell installation procedures
(10) Run STARTNET.BAT
(11) Log in to the network
****************************************************************************
* *
* Banyan Vines Installation (versions 4.x and later) *
* for Grey Cell System 3400 Series Fax/Modem/Ethernet Card *
* *
****************************************************************************
Installation Procedures for Banyan Vines (versions 4.x and later)
Using GCS3000
or
NE2000 ( have to use CARD2.EXE or CARD2CS.EXE )
(1) Create a Banyan directory on your workstation hard disk or VINES
boot diskette. For example: C:>MD \VINES
USING GCS3000
(2) At the DOS prompt, copy the file GCS3000.DOS from \GCS3000\NDIS2\ on
the Grey Cell Drivers Disk and PROTOCOL.INI from the same directory
to the \VINES directory just created.
(3) Copy the files from the VINES Master diskette into the
\VINES directory.
(4) Copy the NDIS driver files from \NDIS directory on the
VINES LAN Drivers diskette into the \VINES directory.
(5) Using an ASCII text editor, edit the CONFIG.SYS file to
include the following lines:
DEVICE=C:\VINES\PROTMAN.DOS /I:C:\VINES
DEVICE=C:\VINES\GCS3000.DOS
(6) Change to the \VINES directory.
(7) Type PCCONFIG and select Network Card Settings, followed
by NDIS Ethernet.
(8) At the PROTOCOL.INI bindings prompt type MS$NE2CLONE.
(9) Press F10 to save and Esc to return to the main menu.
(10) Select Login Environment Settings, followed by Default
Communications Driver, followed by NDIS Ethernet.
USING NE2000 ( have to use CARD2.EXE or CARD2CS.EXE )
(2a) At the DOS prompt, copy the files CARD2.EXE (direct enabler) or
CARD2CS.EXE ( client for Card & Socket Services) from the root
directory of the Grey Cell Drivers Disk. Also copy the PROTOCOL.INI
file from the \NE2000\NDIS2\ directory on the Drivers Disk to the
\VINES directory just created.
(3a) Copy the files from the VINES Master diskette into the
\VINES directory.
(4a) Copy the NDIS driver files from the directory on the
VINES LAN Drivers diskette into the \VINES directory.
(5a) Using an ASCII text editor, edit the CONFIG.SYS file to
include the following lines:
DEVICE=C:\VINES\PROTMAN.DOS /I:C:\VINES
DEVICE=C:\VINES\CARD2(CS).EXE (if using Card & Socket Services)
DEVICE=C:\VINES\NE2NDIS.DOS
(6a) Change to the \VINES directory.
(7a) Type PCCONFIG and select Network Card Settings, followed
by NDIS Ethernet.
(8a) At the PROTOCOL.INI bindings prompt type GCS2000_NIF.
(9a) Press F10 to save and Esc to return to the main menu.
(10a) Select Login Environment Settings, followed by Default
Communications Driver, followed by NDIS Ethernet.
(11) Press Esc to return to the Main Menu and press F10 to
save.
(12) Reboot the PC.
****************************************************************************
* *
* DEC Pathworks Installation *
* for Grey Cell System 3400 Series Fax/Modem/Ethernet Card *
* *
****************************************************************************
Installation Procedure for DEC Pathworks (version 4.1)
Using GCS3000
or
NE2000 ( have to use CARD2.EXE or CARD2CS.EXE )
(1) Run NETSETUP.
(2) Choose Ethernet controller type and select "Other NDIS."
(3) Choose "Other NDIS Information."
(4) Insert the Grey Cell Drivers Disk into the A: drive.
USING GCS3000
(5) When prompted for the path to the driver file, type
A:\GCS3000\NDIS2\GCS3000.DOS
(6) When prompted for the path to the PROTOCOL.INI file,
type:
A:\GCS3000\NDIS2\PROTOCOL.INI
(7) Complete NETSETUP and return to the DOS prompt.
(8) Goto step 10.
USING NE2000 ( have to use CARD2.EXE or CARD2CS.EXE )
(5a) When prompted for the path to the driver file, type
A:\NE2000\NDIS2\NE2NDIS.DOS
(6a) When prompted for the path to the PROTOCOL.INI file,
type:
A:\NE2000\NDIS2\PROTOCOL.INI
(7a) Complete NETSETUP and return to the DOS prompt.
(8a) At the DOS prompt, use an ASCII text editor to open the
CONFIG.SYS file and add the following line
DEVICE=C:\[path]CARD2(CS).EXE ( if using Card & Socket Services )
immediately above the line
DEVICE=C:\[path]NE2NDIS.DOS
where [path] is the path to the directory containing the
NE2NDIS.DOS file.
(9a) Copy the file CARD2(CS).EXE from the root directory of the
Grey Cell Drivers Disk to the directory containing
the NE2NDIS.DOS file.
(10) Reboot the PC.
Note
-----
If the keydisk being configured is in diskette drive
A:, copy the files NE2NDIS.DOS and PROTOCOL.INI to
another drive before configuring the keydisk with
NETSETUP.
Installation Procedure for DEC Pathworks (version 4.0) NDIS Driver
Using GCS3000
or
NE2000 ( have to use CARD2.EXE or CARD2CS.EXE )
(1) Run NETSETUP.
(2) Select "Ethernet board."
(3) Select "Other."
(4) Select NDIS driver.
(5) Insert the Grey Cell Drivers Disk into the A: drive.
USING GCS3000
(6) Enter the path to the driver file as follows:
A:\GCS3000\NDIS2\GCS3000.DOS
(7) Select PROTOCOL.INI.
(8) Enter the path to the PROTOCOL.INI file as follows:
A:\GCS3000\NDIS2\PROTOCOL.INI
(9) Complete NETSETUP and return to the DOS prompt.
(10) Goto step 12.
USING NE2000 ( have to use CARD2.EXE or CARD2CS.EXE )
(6a) Enter the path to the driver file as follows:
A:\NE2000\NDIS2\NE2NDIS.DOS
(7a) Select PROTOCOL.INI.
(8a) Enter the path to the PROTOCOL.INI file as follows
A:\NE2000\NDIS2\PROTOCOL.INI
(9a) Complete NETSETUP and return to the DOS prompt.
(10a) At the DOS prompt, use an ASCII text editor to open the
CONFIG.SYS file and add the following line
DEVICE=C:\[path]CARD2(CS).EXE ( if using Card & Socket Services )
immediately above the line
DEVICE=C:\[path]NE2NDIS.DOS
where [path] is the path to the directory containing the
NE2NDIS.DOS file.
(11a) Copy the file CARD2(CS).EXE from the root directory of the
Grey Cell Drivers Disk to the directory containing
the NE2NDIS.DOS file.
(12) Reboot the PC.
****************************************************************************
* *
* FTP Software PC/TCP *
* for Grey Cell System 3400 Series Fax/Modem/Ethernet Card *
* *
****************************************************************************
Installation Procedure for FTP Software PC/TCP Packet Driver Installation
(1) Install PC/TCP software according to the directions given
in the PC/TCP documentation.
(2) When the installation is complete, copy the file
CARD2(CS).EXE from the root directory of the Grey Cell Drivers Disk
and the file NE2PD.COM from the \NE2000\PACKET directory on the
Drivers Disk to the PC/TCP directory specified in the PC/TCP install
procedures.
(3) (This step not required for PC/TCP versions 2.10 and later.)
Using an ASCII text editor, add the following lines
to your CONFIG.SYS file:
DEVICE=[path]IPCUST.SYS
DEVICE=[path]IFCUST.SYS
where [path] is the drive and directory specified at the
PC/TCP installation.
(4) Reboot the PC.
(5) Change to the directory where your PC/TCP files are
stored and run CARD2(CS).EXE, as follows:
CARD2(CS).EXE ( if using Card & Socket Services )
(6) From the same directory, run NE2PD.COM.
(7) Run the ETHDRV.EXE kernel program supplied with PC/TCP.
This loads the PC/TCP kernel into memory. The packet
driver must always load before the kernel.
(8) Continue your server or workstation startup as instructed
in the PC/TCP documentation.
Installation Procedure for FTP Software PC/TCP NDIS Driver
Using GCS3000
or
NE2000 ( have to use CARD2.EXE or CARD2CS.EXE )
(1) Install PC/TCP software according to the directions given
in the PC/TCP documentation.
USING GCS3000
(2) Use an ASCII text editor to add the following lines to
your CONFIG.SYS file:
DEVICE = C:\NDIS\PROTMAN.SYS /I:C:\NDIS
DEVICE = C:\NDIS\GCS3000.COM
DEVICE = C:\NDIS\DIS_PKT.GUP
(Include the following lines for PC/TCP versions earlier than 2.10 only)
DEVICE = C:\PCTCP\IFCUST.SYS
DEVICE = C:\PCTCP\IPCUST.SYS
(3) Create a directory called \NDIS on your hard disk, as follows:
MD \NDIS
(4) Copy the files GCS3000.DOS and PROTOCOL.FTP from the
\GCS3000\NDIS2\ directory on the Grey Cell Drivers Disk to the
\NDIS directory you created in Step 3.
(5) Rename the PROTOCOL.FTP file PROTOCOL.INI.
(6) Copy all the files from the \NDIS directory on the FTP
Unsupported Software Diskette A to the \NDIS directory
you created in Step 3.
USING NE2000 ( have to use CARD2.EXE or CARD2CS.EXE )
(2a) Use an ASCII text editor to add the following lines to
your CONFIG.SYS file:
DEVICE = C:\NDIS\PROTMAN.SYS /I:C:\NDIS
DEVICE = C:\NDIS\CARD2(CS).EXE ( if using Card & Socket Services )
DEVICE = C:\NDIS\NE2NDIS.DOS
DEVICE = C:\NDIS\DIS_PKT.GUP
(Include the following lines for PC/TCP versions earlier than 2.10 only)
DEVICE = C:\PCTCP\IFCUST.SYS
DEVICE = C:\PCTCP\IPCUST.SYS
(3a) Create a directory called \NDIS on your hard disk, as follows:
MD \NDIS
(4a) Copy the file CARD2(CS).EXE from the root directory of the
Grey Cell Drivers Disk and the files NE2NDIS.DOS and
PROTOCOL.FTP from the \NE2000\NDIS2 directory on the Grey Cell
Drivers Disk to the \NDIS directory you created in Step 3.
(5a) Rename the PROTOCOL.FTP file PROTOCOL.INI.
(6a) Copy all the files from the \NDIS directory on the FTP
Unsupported Software Diskette A to the \NDIS directory
you created in Step 3.
(7) Reboot the PC.
(8) Change to the \NDIS directory and run NETBIND.EXE.
(9) Run the ETHDRV.EXE program supplied with PC/TCP to
complete the installation.
Installation Procedure for FTP Software PC/TCP ODI Driver
Using GCS3000
or
NE2ODI ( have to use CARD2.EXE or CARD2CS.EXE )
(1) Install PC/TCP according to the instructions in your FTP
PC/TCP manual.
(2) (This step is not required for PC/TCP versions 2.10 and later.)
Using an ASCII text editor, add the following
lines to your CONFIG.SYS file:
DEVICE=[path]IPCUST.SYS
DEVICE=[path]IFCUST.SYS
where [path] is the drive and directory specified at the
PC/TCP installation.
USING GCS3000
(3) Copy the file GCS3000.COM from the root directory of the
Grey Cell Drivers Disk and the NET.CFG fi;le from the \GCS3000\ODI\
directory to the PC/TCP directory created in the PC/TCP install
procedure.
(4) To start the workstation, load the software in the
following order:
LSL
GCS3000
ODIPKT (Use the version supplied with PC/TCP)
ETHDRV
USING NE2000 ( have to use CARD2.EXE or CARD2CS.EXE )
(3a) Copy the file CARD2(CS).EXE from the root directory of the
Grey Cell Drivers Disk and the NE2ODI.COM file from the
\NE2000\ODI\ directory on the drivers disk to the PC/TCP
directory created in the PC/TCP install procedure.
(4a) To start the workstation, load the software in the
following order:
CARD2(CS).EXE ( if using Card & Socket Services )
LSL
NE2ODI
ODIPKT (Use the version supplied with PC/TCP)
ETHDRV
(5) Continue your server or workstation startup as instructed
in the PC/TCP documentation.
Installation Procedure for ODI with FTP Software PC/TCP and NetWare
If you need to run Novell NetWare concurrently with FTP PC/TCP,
proceed as follows:
Using GCS3000
or
NE2000 ( have to use CARD2.EXE or CARD2CS.EXE )
(1) Install PC/TCP according to the instructions in your FTP
PC/TCP manual.
(2) (This step not required for PC/TCP versions 2.10 and later.)
Using an ASCII text editor, add the following
lines to your CONFIG.SYS file:
DEVICE=[path]IPCUST.SYS
DEVICE=[path]IFCUST.SYS
where [path] is the drive and directory specified in the
PC/TCP installation.
USING GCS3000
(3) Copy the file GCS3000.COM from the root directory of the
Grey Cell Drivers Disk and the file NET.CFG from the \GCS3000\ODI\
directory on the Disk to the PC/TCP directory created in the PC/TCP
Install procedure.
(4) To start the workstation, load the software in the
following order:
LSL
GCS3000
IPXODI
ODIPKT (Use the version supplied with PC/TCP)
ETHDRV
NETX or VLM
USING NE2000 ( have to use CARD2.EXE or CARD2CS.EXE )
(3a) Copy the files CARD2(CS).EXE from the root directory of the
Grey Cell Drivers Disk and the file NE2ODI.COM from the
\NE2000\ODI directory on Disk to the PC/TCP directory created
in the PC/TCP install procedure.
(4a) To start the workstation, load the software in the
following order:
CARD2(CS).EXE ( if using Card & Socket Services )
LSL
NE2ODI
IPXODI
ODIPKT (Use the version supplied with PC/TCP)
ETHDRV
NETX or VLM
(5) Change to the network drive (usually F:\LOGIN)
(6) Log in to the network.
(5) Change to the network drive (usually F:\LOGIN)
(6) Log in to the network.
****************************************************************************
* *
* IBM LAN Support Program (NDIS Driver) *
* for Grey Cell System 3400 Series Fax/Modem/Ethernet Card *
* *
****************************************************************************
These instructions will set up the NE2000 or the GCS3000 NDIS driver.
Using GCS3000
or
NE2000 ( have to use CARD2.EXE or CARD2CS.EXE )
USING NE2000
(1) Run CARDCHEK in the diagnose directory on the Grey Cell Drivers Disk
and make a note of the IRQ and IO which has been assigned.
USING GCS3000
(1a) Run ASK-RSC in the diagnose directory on the Grey Cell Drivers Disk
and make a note of the IRQ, IO, COM Port and Memory which is free.
(2) Enter through the introduction pages.
(3) When the setup screen appears select YES for 'Do you have Driver Diskette.'
USING NE2000
(4) The 'Process Drivers Diskette Appears'
Select the path A:\NE2000\NDIS2
USING GCS3000
(4a) The 'Process Drivers Diskette Appears'
Select the path A:\GCS3000\NDIS2
(5) Follow the on screen instructions.
(6) Highlight the Grey Cell Card and Select Change Parameters
(7) The IRQ, I/O, (COM) & (Memory) must match the ones stated in step 1 (1a).
(8) Select Install and Reboot the Systems.
****************************************************************************
* *
* Microsoft LAN Manager (versions 2.1 and later) (NDIS Driver) *
* for Grey Cell System 3400 Series Fax/Modem/Ethernet Card *
* *
****************************************************************************
These instructions will set up for the NE2000 NDIS driver. If you wish to
use the GCS3000 driver, follow these instructions and make the amendments
shown at the end.
(1) Begin the installation of your LAN Manager using the MS supplied
"setup".
(2) When prompted to select the available network adapter driver,
choose "Other Driver."
(3) Insert the Grey Cell Drivers Disk .
USING NE2000
(4) Select "Grey Cell 3400 Fax/Modem/Ethernet Card (NE2000 Mode)" from the menu.
USING GCS3000
(4a) Select "Grey Cell 3400 Fax/Modem/Ethernet Card (w/ Enabler)" from the menu.
(5) Continue with the installation until it is completed.
(6) Reboot the PC.
****************************************************************************
* *
* Microsoft LAN Manager (version 2.0) NDIS Driver *
* for Grey Cell System 3400 Series Fax/Modem/Ethernet Card *
* *
****************************************************************************
These instructions will set up for the NE2000 NDIS driver. If you wish to
use the GCS3000 driver, follow these instructions and make the amendments
shown at the end.
(1) Begin the installation of your LAN Manager using the MS supplied
"setup".
(2) Insert the Grey Cell Drivers Disk .
USING NE2000
(4) Select "Grey Cell Fax/Modem/Ethernet Card (NE2000 Mode)" from the menu.
USING GCS3000
(4a) Select "Grey Cell 3400 Fax/Modem/Ethernet Card (w/ Enabler)" from the menu.
(5) Proceed with the installation.
(6) At the Network Drivers menu, select "Grey Cell Fax/Modem/Ethernet Card"
from the list of drivers.
(5) Continue with the installation until it is completed.
(6) Reboot the PC.
****************************************************************************
* *
* Microsoft Windows Networks *
* for Grey Cell System 3400 Series Fax/Modem/Ethernet Card *
* *
****************************************************************************
Windows for Workgroups Version 3.1
Windows for Workgroups Version 3.11
Windows 95. See A:\WIN95\README.TXT
Windows NT 3.5x See A:\WINNT\README.TXT
See the Express Set Up in the Main User's Manual
for installation details, or read the relevant .TXT file
on this drivers disk.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.