README Driver File Contents (8738doslin.zip)

Audio driver for CM8338/CM8738 chips by Chen-Li Tien


HARDWARE SUPPORTED
================================================================================
C-Media CMI8338
C-Media CMI8738
On-board C-Media chips


WHAT'S NEW
================================================================================

  1. Support modem interface for 8738. (select in kernel configuration)
  2. Enable S/PDIF-in to S/PDIF-out (S/PDIF loop).
  3. Enable 4 channels analog duplicate mode on 3 jack or 4 jack
     configurateion.
  4. Enable joystick support. (joystick driver needed)


STEPS TO BUILD DRIVER
================================================================================

  1. Backup the Config.in and Makefile in the sound driver directory
     (/usr/src/linux/driver/sound).
     The Configure.help provide help when you config driver in step
     4, please backup the original one (/usr/src/linux/Document) and
     copy this file.
     The cmpci is document for the driver in detail, please copy it
     to /usr/src/linux/Document/sound so you can refer it. Backup if
     there is already one.

  2. Extract the tar file by 'tar xvzf cmpci-xx.tar.gz' in the above
     directory.

  3. Change directory to /usr/src/linux

  4. Config cm8338 driver by 'make menuconfig', 'make config' or
     'make xconfig' command.

  5. Please select Sound Card (CONFIG_SOUND=m) support and CMPCI
     driver (CONFIG_SOUND_CMPCI=m) as modules. Resident mode not tested.
     For driver option, please refer 'DRIVER PARAMETER'

  6. Compile the kernel if necessary.

  7. Compile the modules by 'make modules'.

  8. Install the modules by 'make modules_install'


INSTALL DRIVER
================================================================================

  1. Before first time to run the driver, create module dependency by
     'depmod -a'

  2. To install the driver manually, enter 'modprobe cmpci'.

  3. Driver installation for various distributions:

    a. Slackware 4.0
       Add the 'modprobe cmpci' command in your /etc/rc.d/rc.modules
       file.so you can start the driver automatically each time booting.

    b. Caldera OpenLinux 2.2
       Use LISA to load the cmpci module.

    c. RedHat 6.0 and S.u.S.E. 6.1
       Add following command in /etc/conf.modules:

       alias sound cmpci

	also visit http://www.cmedia.com.tw for installation instruction.

DRIVER PARAMETER
================================================================================

  Some functions for the cm8738 can be configured in Kernel Configuration
  or modules parameters. Set these parameters to 1 to enable.

  spdif_loop:   Enable S/PDIF loop, this route S/PDIF-in to S/PDIF-out
                directly.
  four_ch:      Enable 4 channels mode, rear-out or line-in will output
                the same as line-out.
  rear_out:     Enable this if you have independent rear-out jacket on
                your sound card, otherwise line-in will be used as
                rear-out.
  modem:	You will need to set this parameter if you want to use
		the HSP modem. You need install the pctel.o, the modem
		driver itself.
  joystich:	Enable joystick. You will need to install Linux joystick
		driver.
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: ftp, load: 1.34