[DRIVER] ; Interpolation method used in Enhanced full duplex, ( Linear or Filter ) Interp8=Linear Interp16=Linear SaveSettingsOnExit=OFF DMATimingMode=1 [APPLETS] InputControlPath=D:\MS23\WINUTIL InputApplet=cs32baip.exe OutputControlPath=D:\MS23\WINUTIL OutputApplet=cs32baop.exe OPAlwaysOnTop=OFF IPAlwaysOnTop=OFF [MIXER] WaveVolumeOffset=48 ; Line ( LINE ) or microphone ( MIC ) selected as input InputSelection=MIC ; Line input gain. 0 to 65535=0 to 22.5 db gain lLineVolume=43690 rLineVolume=43690 LineGang=ON ; Mic input gain. 0 to 65535=0 to 22.5 db gain lMicVolume=43690 rMicVolume=43690 MicGang=ON ; Aux input gain. 0 to 65535=0 to 22.5 db gain lAuxInVolume=43690 rAuxInVolume=43690 AuxInGang=ON ; Loop back input gain. 0 to 65535=0 to 22.5 db gain lLoopBackInputVolume=43690 rLoopBackInputVolume=43690 LoopBackInputGang=ON ; Monitor attenuation. 0 - 65535=mute to no attenuation. MonitorVolume=0 MonitorMute=ON MonitorMode=Recording ; CS4215 output atten setting. 0 - 65535=full attenuation to no attenuation in ; 32 1.5 Db steps. lMasterVolume=65535 rMasterVolume=65535 MasterMute=OFF MasterGang=ON ; Aux Volume setting 0 - 65535. 0=full attenuation, 65535 = no attenuation. lAuxVolume=65535 rAuxVolume=65535 AuxMute=OFF AuxGang=ON ; Aux2 volume setting 0 - 65535. 0=full attenuation, 65535 = no attenuation. lAux2Volume=65535 rAux2Volume=65535 Aux2Mute=OFF Aux2Gang=ON ; Line Mix volume setting 0 - 65535. 0=full attenuation, 65535 = no attenuation. lLineMixVolume=65535 rLineMixVolume=65535 LineMixMute=OFF LineMixGang=ON ; Mono Mix volume setting 0 - 65535. 0=full attenuation , 65535 = no attenuation. MonoVolume=0 MonoMute=OFF ; MonoOutMute indicates the state of the mono output mute. MonoOutMute=ON ; MicBoost indicates if 20db additional boost is added when the mic input is selected. MicBoost=ON HWMUTE=0,1,E ; Virtual Volume master lVirtMaster=42280 rVirtMaster=42280 LowPriInputSelection=MIC lLowPriMicVolume=32256 rLowPriMicVolume=32256 LowPriMicBoost=ON lLowPriLineVolume=39680 rLowPriLineVolume=39680 lLowPriLoopBackInputVolume=38400 rLowPriLoopBackInputVolume=38400 lLowPriAuxInVolume=17664 rLowPriAuxInVolume=17664 VirtMasterMute=OFF VirtMasterGang=ON MicAGC=OFF [RECORD] ; HighPassFilter ON or OFF, when on will reduce signal offset at the expense of slightly ; lower fidelity ( probably not audible ) at low frequencies. HighPassFilter=Off ; The default dither state. This may be over-ridden at some record formats. Dither=OFF [Meter] ; Control Panel Section ; Tells the control panel to come up running the VU meter when the inputs dialog is shown. MeterDisplay=OFF ; DecayRate defines how quickly the VU meter bars decay ; 0=no decay, 255=immediate and full decay. default = 8. DecayRate=16 ; The number of time / second that the VU meter will update. default=20. VUUpdateRate=10 [CONTROLS] ; This section dictates the controls which will be present on a WSS mixer. ;****************************************** ;* Mixer Lines To include ;****************************************** MixerSources=Wave,Monitor,Mono,Line,Aux1,Aux2 ;MixerSources=Line,Monitor,Aux1,Wave ;****************************************** ;* Input Lines To include ;****************************************** InputSources=Line,Aux1,Loop,Mic ;InputSources=Mic,Line ;********************************************************** ;* Line Source Descriptions ( short/long names ) ;********************************************************** ShortNameLine=Synth ;LongNameLine= ShortNameAux1=Line/CD ;LongNameAux1= ShortNameAux2=CD ;LongNameAux2= ShortNameMono=PC Speaker ;LongNameMono= ;ShortNameMonitor=Monitor ;LongNameMonitor= ;ShortNameWave= ;LongNameWave= ShortNameMic=Mic ;LongNameMic= ShortNameLoopback=Mix Out ;LongNameLoopback= ;********************************************************** ;* Thing connected to Sources entries ;********************************************************** ; These are the possible assignment values: ; Undefined, Digital, Line, Microphone, Synthesizer ; CompactDisk, Telephone, PCSpeaker, WaveOut, Auxiliary, Analog SourceForLine=Synthesizer SourceForAux1=CompactDisk SourceForAux2=Auxiliary SourceForMono=PCSpeaker SourceForMic=MicrophoneDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.