Quatech, Inc. SDS
** Release History **
***************************************************************************
Release 4.00 February 14, 2003
***************************************************************************
First release for production.
***************************************************************************
Release 4.01 February 27, 2003
***************************************************************************
Fixed DHCP request message which prevented some DHCP servers from handing
the SDS an IP address. Changed initial state of RTS control line to match
the state of a PC serial port.
***************************************************************************
Release 4.04 September 26, 2003
***************************************************************************
Support added for SSE-200/300D. Web page contact information updated.
Sockets mode programming SDK support added.
***************************************************************************
Release 4.10 January 16, 2004
***************************************************************************
Added serial tunneling, raw TCP, and AutoConnect TCP as new modes of
operation.
***************************************************************************
Release 4.20 May 14, 2004
***************************************************************************
Web configuration interface upgraded to improve ease of use.
***************************************************************************
Release 4.26 December 15, 2004
***************************************************************************
Added raw UDP mode of operation which include point-to-point, broadcast,
and multicast addressing modes. Version 4.26 can only upgrade 4.xx
versions.
***************************************************************************
Release 5.10 January 16, 2004
***************************************************************************
Added SNMP support. 4.XX versions cannot be upgraded to 5.10 with SNMP
support. Version 5.10 only available as base version pre-installed from
factory.
***************************************************************************
Release 5.20 May 14, 2004
***************************************************************************
Web configuration interface upgraded to improve ease of use. Version 5.20
cannot upgrade 4.xx versions.
***************************************************************************
Release 5.26 December 15, 2004
***************************************************************************
Added raw UDP mode of operation which includes point-to-point, broadcast,
and multicast addressing modes. Version 5.26 cannot upgrade 4.xx versions.
***************************************************************************
Release 6.26 November 8, 2004
***************************************************************************
Added raw UDP mode of operation which includes point-to-point, broadcast,
and multicast addressing modes. Added support for SSE/DSE-100,200,400
products based on Freescale MPC852T processor. Version 6.26 only available
as base version pre-installed from factory.
***************************************************************************
Release 6.29 April 29, 2005
***************************************************************************
Upgrade for 6.xx versions only and as base version pre-installed from
factory on SSE/DSE-100,200,400 products. Wireless UDP multicast fixed.
Fixed problem with DHCP setting not being correctly saved. Enhancements
made to user settings for wireless web setup. Added Dynamic IP support.
Fixed use of alpha hex character use in WEP key settings. Hex WEP key
user input limited to two characters. Same MAC used for wireless and wired
communications. Added ability to change default TCP port 5000 assignment
for first serial port.
***************************************************************************
Release 6.30 May 18, 2005
***************************************************************************
Upgrade for 6.xx versions only and as base version pre-installed from
factory on SSE/DSE-100,200,400 products. Fixed problem of DHCP not working
when WEP is used. Fixed problem where heartbeat timer was not closing port
if last data received is on serial port in raw TCP, auto TCP, and raw UDP
modes.
***************************************************************************
Release 6.32 July 19, 2005
***************************************************************************
Upgrade for 6.xx versions only and as base version pre-installed from
factory on SSE/DSE-100,200,400 products. Fixed problem of serial tunneling
only working in n,8,1 mode. Removed glitches on RTS/DTR lines during
transitions. This was causing problems in serial tunneling mode if RTS/CTS
selected. Added WPA-PSK support for 802.11b wireless products.
***************************************************************************
Release 6.39 May 1, 2006
***************************************************************************
Upgrade for 6.xx versions only and as base version pre-installed from
factory on SSE/DSE-100,200,400 products. Changes made to WEP to support
use of all 4 keys. Initial state of serial port pins corrected.
Capability added to allow use of secondary oscillator for non-standard
baud rates. Parity error reporting problem fixed. Fixed problem that
caused port to lockup when using XON/XOFF. Data led changed so that it
only flashes on reception/transmission of serial port data and flashes
once when the port is opened. Raw UPD HTML help pop-up box correction
made for starting UDP port number. Improved low latency throughput.
***************************************************************************
Release 7.39 May 1, 2006
***************************************************************************
Upgrade for 7.xx versions only and as base version pre-installed from
factory on QSE/ESE-100,200,400 products. Wireless support added matching
functionality as contained in version 6.39 for single port units. Data led
changed so that it only flashes on reception/transmission of serial port
data and flashes once when the port is opened. Raw UPD HTML help pop-up
box correction made for starting UDP port number. Improved low latency
throughput. Fixed problems with web server not functioning and only 6 of 8
ports working when trying to use all eight ports in RAW UPD mode. Fixed
problem where heartbeat timer was not closing port if last data received is
on serial port in raw TCP, auto TCP, and raw UDP modes.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.