release_note.txt Driver File Contents (neonmnc_lan_xp.zip)

SiS191/190 10/100/1000Mbs adapter manufacture test tools package release note

======
v2.02
======
1. Initial release.

======
v2.03
======
1. Modify the naming of executive file to indicate it is used for SiS191/190 
   only. ex. lan19x.exe
2. Add the needed file "MODERN.FON" while executing exlb19x.exe. 
3. Fix the issue fail to run Diag.exe.  

======
v2.04
======
1. DIAG19x.exe: Fix the problem of internal loopback test fail that happened 
   after external loopback test in half duplex mode. 

======
v2.05
======
1. DIAG19x.exe: Rx got packet when external loopback test failed in half duplex mode. 
2. DIAG19x.exe: Fix the issue that internal loopback test fails sometimes.

======
v2.06
======
1. DIAG19x.exe: Fix 2 station test package lose issue.

======
v2.09
======
1. DIAG19x.exe: Fix the issue that Node ID cannot be read.
2. DIAG19x.exe: Fix the issue of Tx error for Diag19x 100/Full internal loopback test.
3. DIAG19x.exe: Fix the issue of failure for MII and PCI registers test.
4. DIAG19x.exe: It is ready for Broadcom AC131 and Marvell 88e1111 PHY.

======
v2.10
======
1. Realtek RTL8211 PHY is supported.
2. Add 1000 Mbps external loopback test for RTL8211 PHY.

======
v2.11
======
1. Fix the issue that exlb19x can't set font.

======
v2.12
======
1. ee19x.exe can support 190/191 EEPROM signature auto recognization.

======
v2.13
======
1. Fix the halt issue on SiS656 & SiS649.

======
v2.14
======
1. Support SiS191 REV.01 on SiS966.
2. Support Marvell PHY new chip (PHY ID: 0x01410cc2)
3. Support RGMII mode.

======
v2.15
======
1. Fix the failuration of Agere MII register test. 

======
v2.16
======
1. Fix the conflict between PCI register test and USB Legacy support.

======
v2.17
======
1. Fix that setting Magic packet to power into S5 can not wake up

======
v2.18
======
1. Fix the wrong message will show when testing external loopback

======
v2.19
======
1. Support Attansic Phy F1

======
v2.20
======
1. Fix the link change wakeup event problem

======
v2.21
======
1. Solve RGMII will be set when south bridge is 996L but device is sis190

======
v2.22
======
1. Solve packet lost with Attansic phy.


======
v2.23
======
1. Workaround for AUSU motherboard (966+10M/100M PHY)
2. Detected cable is connect or not on Lan19x  and exlb19x

======
v2.24
======
1. Solve that the result will be pass if cable is unpluged during testing.

======
v2.25
======
1. Modify MII test for Realtek PHY RTL8021 (Offest 0x05, bit 10 & bit 11)

======
v2.26
======
1. Update ee19x to v1.01, but Diag19x, lan19x and exlb19x are still in v2.25

======
v2.27
======
1. Workaround for 968, and Diag19x, lan19x and exlb19x are in v2.27 for consistence of version
 
======
v2.28
======
1. Solve Media Tyape will show "Cable disconnect" and Auto Config will show "Cable disconnect"

======
v2.29
======
1. HW workaround

======
v2.30
======
1. Workaround for PHY RTL8211B

======
v2.31
======
1. Produce Lantest.log when excute lan19x.exe and exlb19x.exe
2. Update EE19x to v1.03 

======
v2.32
======
1. Solve that Regtest is failed in sis968 when load mac from eeprom
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web1, load: 0.75