Accton Technology Corporation STREAM DRIVER ON SCO UNIX SERVER INSTALLATION ============================================= Your Driver Diskette should contain the following files: -------------------------------------------------------------- Files Contents -------------------------------------------------------------- UNIX.TXT Text file about driver installation for the UNIX Server UNIXDRVR.TAR Accton device drivers packaged for UNIX (in tar format) F2TAR.EXE Utility to transfer UNIXDRVR.TAR onto a formatted diskette. -------------------------------------------------------------- Installation Procedure ---------------------- 1. Prepare a formatted diskette on any DOS machine. For example, type: C>format a: Note: Make sure your diskette is free from bad sectors. Verify this using the DOS CHKDSK command 2. Run F2TAR.EXE to generate an Installation Diskette for the UNIX system. a. After executing the "f2tar" command, the following message will be shown on the screen: "Target drive letter (press 'A' or 'B'):" Press 'A' for the first drive, 'B' for second drive. b. Then "f2tar" will load the data file "unixdrvr.tar" into memory and display the following messages: "Reading file, please wait." ...... "Done." c. Note that if you are using the same drive for both Source Diskette and UNIX Installation Diskette, "f2tar," the following message will appear onscreen: "Remove the original diskette from drive A" or "Remove the original diskette from drive B" d. Insert the formatted diskette into your floppy drive (A: or B:) when your system prompts you to do so. Then press <Enter> to proceed. e. After transferring the files, the following messages will be shown onscreen. "Generating UNIX Installation Diskette on drive ()" "Press [Ctrl][C] to abort." If you want to abort the operation, press <Ctrl> and <C> at the same time. Please wait for a few seconds, and the UNIX Installation Diskette will be created. Note that the resulting diskette is in UNIX tar format; it cannot be read by DOS. 3. When data file transfer is complete, the following message will appear onscreen. "Please remove the diskette from drive A". 4. If you are using the same drive for both Source Diskette and UNIX Installation Diskette, the following message will also be shown onscreen. "Please insert the original diskette to drive A" "Press [ENTER] to continue ..." 5. Follow screen instructions to complete the process. 6. Remove the UNIX Installation Diskette and login to the UNIX system as root. 7. Now the UNIX Installation Diskette is ready for use. Login to UNIX system as supervisor (root). (Note: Make sure that the current directory is "/" using UNIX command - pwd.) 8. The following sections describe the configuration of the driver. It is suggested that you should perform these instructions in the singler-user environment. Run custom utility and select the "Install new package" option. It will prompt you to insert 16-BIT Ethernet LLI driver disk. 9. After reading drive A, it will show a message prompting you to use "netconfig" or "mkdev <driver>" (this case- en16) to add drivers into your system. If you use "mkdev en16", you must also use "mkdev tcp" and select "en16" for this LLI driver in order to complete configuration. Anyway, you should be prompted to set up the chain of protocols and drivers. Also you are going to define the Internet TCP/IP address and the broadcast address. Note that if you use BSD 4.2 your broadcast address should be all 0s. In case of BSD 4.3 the broadcast address should be all 1s. 10. Use the program "1step" to configure Accton's 16-bit Ethernet adapter. Remember to set the I/O and IRQ the same as in the netconfig or mkdev session. 11. If you encounter any problems during installation, (i.e., an error message appears onscreen) call your dealer for assistance. Content List of UNIX driver --------------------------- /usr/lib/lli/en16/Master /usr/lib/lli/en16/Node /usr/lib/lli/en16/README /usr/lib/lli/en16/Space.c /usr/lib/lli/en16/System /usr/lib/lli/en16/Driver.o /usr/lib/lli/en16/info /usr/lib/lli/info/en160 /usr/man/cat.ADM/set165.ADM /etc/set165 set165 is a setup program under Unix for setting the configuration of the EN165X adapter. After installing the driver into the Unix environment, you can use "man set165" to retrieve more information about set165. Trademarks ---------- All trademarks or brand names mentioned are properties of their respective companies. ===End===Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.