UNIX.TXT Driver File Contents (Accton_en165x.zip)

		       Accton Technology Corporation
	       STREAM DRIVER ON SCO UNIX SERVER INSTALLATION
	       =============================================

Your Driver Diskette should contain the following files:
--------------------------------------------------------------
Files		 Contents
--------------------------------------------------------------
UNIX.TXT       Text file about driver installation for the
	       UNIX Server
UNIXDRVR.TAR   Accton device drivers packaged for UNIX
	       (in tar format)
F2TAR.EXE      Utility to transfer UNIXDRVR.TAR onto a
	       formatted diskette.
--------------------------------------------------------------

Installation Procedure
----------------------
1. Prepare a formatted diskette on any DOS machine.
	For example, type:

	C>format a:

Note: Make sure your diskette is free from bad sectors.
		Verify this using the DOS CHKDSK command

2. Run F2TAR.EXE to generate an Installation Diskette
	for the UNIX system.

	a. After executing the "f2tar" command, the
		following message will be shown on the screen:

	"Target drive letter (press 'A' or 'B'):"

	Press 'A' for the first drive, 'B' for second drive.

	b. Then "f2tar" will load the data file
		"unixdrvr.tar" into memory and display the
		following messages:

		"Reading file, please wait."
		......
		"Done."

	c. Note that if you are using the same drive for
		both Source Diskette and UNIX Installation
		Diskette, "f2tar," the following message will
		appear onscreen:

		"Remove the original diskette from drive A"
		or
		"Remove the original diskette from drive B"

	d. Insert the formatted diskette into your
		floppy drive (A: or B:) when your system prompts
		you to do so. Then press <Enter> to proceed.

	e. After transferring the files, the following
		messages will be shown onscreen.

		"Generating UNIX Installation Diskette on drive ()"
		"Press [Ctrl][C] to abort."

		If you want to abort the operation, press <Ctrl> and <C>
		at the same time.

		Please wait for a few seconds, and the UNIX
		Installation Diskette will be created. Note
		that the resulting diskette is in UNIX tar format;
		it cannot be read by DOS.

3. When data file transfer is complete, the following message
	will appear onscreen.

	"Please remove the diskette from drive A".

4. If you are using the same drive for both Source
	Diskette and UNIX Installation Diskette, the
	following message will also be shown onscreen.

	"Please insert the original diskette to drive A"
	"Press [ENTER] to continue ..."

5. Follow screen instructions to complete the process.
6. Remove the UNIX Installation Diskette and login to
	the UNIX system as root.
7. Now the UNIX Installation Diskette is ready for use.
	Login to UNIX system as supervisor (root).

	(Note: Make sure that the current directory is "/"
	 using UNIX command - pwd.)

8. The following sections describe the configuration of
	the driver. It is suggested that you should perform
	these instructions in the singler-user environment.

	Run custom utility and select the "Install new package"
	option. It will prompt you to insert 16-BIT Ethernet
	LLI driver disk.

9. After reading drive A, it will show a message prompting
	you to use "netconfig" or "mkdev <driver>"
	(this case- en16) to add drivers into your system.

	If you use "mkdev en16",  you must also use "mkdev tcp"
	and select "en16" for this LLI driver in order to
	complete configuration.

	Anyway, you should be prompted to set up the chain of
	protocols and drivers. Also you are going to define the
	Internet TCP/IP address and the broadcast address. Note
	that if you use BSD 4.2 your broadcast address should be
	all 0s. In case of BSD 4.3 the broadcast address should
	be all 1s.

10.   Use the program "1step" to configure Accton's
	 16-bit Ethernet adapter. Remember to set the I/O and IRQ
	 the same as in the netconfig or mkdev session.

11. If you encounter any problems during installation,
	 (i.e., an error message appears onscreen)
	 call your dealer for assistance.


Content List of UNIX driver
---------------------------

 /usr/lib/lli/en16/Master
 /usr/lib/lli/en16/Node
 /usr/lib/lli/en16/README
 /usr/lib/lli/en16/Space.c
 /usr/lib/lli/en16/System
 /usr/lib/lli/en16/Driver.o
 /usr/lib/lli/en16/info
 /usr/lib/lli/info/en160
 /usr/man/cat.ADM/set165.ADM
 /etc/set165

set165 is a setup program under Unix for setting the configuration
of the EN165X adapter. After installing the driver into the Unix
environment, you can use "man set165" to retrieve more information
about set165.

Trademarks
----------

All trademarks or brand names mentioned are properties
of their respective companies.

===End===

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: ftp, load: 1.83