1. j3239a.exe Driver
2. NW411.TXT File Contents

NW411.TXT Driver File Contents (j3239a.exe)

		  SOFTWARE INSTALLATION INSTRUCTIONS
	   FOR NOVELL NETWARE VERSION 4.11 ODI SERVER DRIVER
	     HP J3239A DeskDirect EL-10 ISA Combo Adapter


 The driver is based on the latest version 3.3 of the ODI specification.

    \NETWARE\HPEIOD.LAN    Novell NetWare version 4.11 Server Driver
    \NETWARE\HPEIOD.LDI    Installation Information File for
			   Novell NetWare version 4.11 Server Driver



 ==============================
 GENERAL INSTALLATION PROCEDURE
 ==============================

 1. Install NetWare 4.11.

    Complete the software installation procedures for the NetWare 4.11
    server.  See the Novell documentation for installing NetWare.


 2.  Update the server with files from the Support Disk for HP J3239A.

    NetWare 4.11 provides two different ways to load a new LAN driver.
    One  method is to copy the new file(s) onto the server and then
    either load the driver by typing on the command line or edit
    AUTOEXEC.NCF to load the driver.  The other method is (1) to load
    INSTALL.NLM and use it to select and load your new driver and
    (2) to edit AUTOEXEC.NCF.


    Manual Loading of Server Driver
    ===============================

    1. Start the server.  Load and bind the HP server driver.

    2. At the NetWare prompt (indicated by a colon), load the driver:


       load D:\hpeiod
       bind ipx to hpeiod net=X

	  D is the path to the server driver.
	  X is the NetWare Network number you choose.

    3. Add the load and bind statements to your server's AUTOEXEC.NCF
       file, so that the adapter driver loads automatically each time
       the server starts.


    Using INSTALL.NLM
    =================

    1. At the NetWare prompt, load the INSTALL.NLM program.

    2. Select "LAN Driver Options (Configure/Load/...)" and [ENTER].

    3. Press [INSERT] to specify other drivers to install.

    4. Press [F3].  Enter the driver path, for example, "a:\netware"

    5. Select the HPEIOD.LAN driver in your selection list to start the
       driver loading and binding procedure.



 ==============
 Hints and Tips
 ==============

 1. Installing multiple adapters:

    If installing multiple adapters, each adapter must have a
    different NET number and SLOT number.  Also, it is a good idea to
    name each adapter. Example:

	  load D:\hpeiod slot=3  name=LAN_A
	  bind ipx to LAN_A  net=222
	  load D:\hpeiod slot=5  name=LAN_B
	  bind ipx to LAN_B  net=333


 2. Installing one adapter with multiple frame types:

    When binding multiple frame types to one adapter, enter a LOAD and
    BIND statement for each frame type.  Each LOAD statement uses the same
    SLOT number, but each BIND statement needs a unique network number.
    NetWare 3.12 allows up to four different frame types, and the adapter
    supports all four, as follows:

       Ethernet_802.3
       Ethernet_802.2
       Ethernet_II
       Ethernet_SNAP
.


 ==============
 ERROR MESSAGES
 ==============

 "The board cannot be found."
    Possible cause: The adapter does not exist or driver does not
		    recognize the adapter.
    Solution: Check that the HP J3239A adapter is fully seated in the
	      correct slot.

 "Board RAM failed the memory test."
    Possible cause: The RAM buffer on the adapter failed.
    Solution: Try a different HP J3239A adapter.

 "The board did not respond to the initialization command."
    Possible cause: The driver recognized the adapter but the adapter
		    fails to respond.
    Solution: Try a different HP J3239A adapter.

 "There is no cable connecting to adapter."
    Possible cause: The adapter is not connected to the network cable,
		    or the adapter's transceiver has failed.
    Solution: Check the cable connections and try again.


<End of File>