PKTDRV.TXT Driver File Contents (DR_8036TX_DRv104_All.zip)

*******************************************************************************
*                             SMC Networks, Inc.                              *
*                        EZ CardBus-II 10/100 PC Card                         *
*                                                                             *
*                         Packet Driver Installation                          *
*                                                                             *
*                    Copyright (C) 2001 SMC Networks, Inc.                    *
*                            All Rights Reserved.                             *
*******************************************************************************

I. The driver SMCPKT.COM can be used for the following:
   
     SMC EZ CardBus-II 10/100 PC cards

SMCPKT          syntax:

SMCPKT          [-#] [-a] [-t] [-f] [-s] [-n] [-w] [-u] [-h] <PD_INT_NO>

Parameter       Explain
-----------------------------------------------------------------------------
[-#]            The "-#" option will let the driver work on a specific adapter
                when multiple EZ CardBus-II PC Card are found in the computer
                system.  For example, "-1" means the first adapter will be
                activated by the driver, "-2" means the second adapter will
                be activated, ... etc.

                A maximum of 4 adapters are supported simulaneously.

[-a]            The "-a" option will let driver perform automatic media
                detection during driver initialization.  The detection
                sequence is

                TP 100Mbps Full Duplex ---> TP 10Mbps Full Duplex --->
                TP 100Mbps Half Duplex ---> TP 10Mbps Half Duplex

                If no physical media is attached to the adapter then TP
                100Mbps Full Duplex is the default media.

[-t]            The "-t" option is to use Twisted Pair (RJ-45) (10BASE-T) as
                the transmission media. And it is also the default setting.

[-f]            The "-f" option enables FULL_DUPLEX feature of the adapters.
                It has no effect except when Twisted Pair is used.

[-s]            The "-s" option sets the adapter line speed to 100Mbps. It is
                a dedicated option for the EZ CardBus-II PC Card.

[-n]            Your NOVELL server uses NOVELL ISO-like packets. Your NOVELL
                workstation uses NOVELL 8137 packets. You can use this option
                to convert NOVELL 8137 packets into NOVELL ISO-like packets.

[-w]            Steve Wallace added a hack to let the packet drivers run under
                Windows. This is not to be construed with the proper solution,
                which is to write a TCP/IP package for Windows.

                This hack is enabled only when you use the '-w' switch.

[-u]            This option unloads the Packet Driver.

[-h]            This option displays the on-line help.

<PD_INT_NO>     This specifies the software interrupt (INT) where you'll load
                the packet driver. It must be in the range 0x60 to 0x80.

-----------------------------------------------------------------------------
Notice!!  The PC/TCP kernel, by default, is loaded at interrupt 0x61
          (so don't load the packet driver there!)


SMCOPEN.EXE is the EZ CardBus-II 10/100 PC card enabling program for the MS-DOS
system. Before you can use any of the DOS mode drivers, such as the Novell DOS
ODI driver, the NDIS2 driver, the packet driver, or the diagnostic program, you
have to run SMCOPEN.EXE to enable the EZ CardBus-II 10/100 PC card first.

Example:

The following command line loads the
EZ CardBus-II PC Card Packet Driver at software interrupt 60h, transmission
media is automatical-detected:

                SMCOPEN
                SMCPKT -a 0x60  or SMCPKT 0x60

** Note **
   The default transmission media is automatic-detection.
   The prefix 0x prepending the parameters represents the number is in hexadecimal format.

TRADEMARKS
==========
All Tademarks or Brand names mentioned are properties of their respective
companies.
== End of File ==
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web4, load: 0.92