OEMSETUP.INF Driver File Contents (DR_SMC9432_all.zip)

; OEMSETUP FILE FOR SMC EtherPower II 10/100 Ethernet adapters
;   WNT version 4.0 - V1.30
;
;   Supported adapters:
;      SMC EtherPower II 10/100
;
; Usage:
;
;     This file is the installation/configuration/deinstallation
;     procedure of the Smcpwr2n driver for Windows NT.  It can be
;     called from Windows Setup directly, or via the Windows NT
;     Networks Control Program Applet (NCPA) from inside the Windows
;     Control Panel.
;
; Modified:
;
;	01/15/98	John Hardesty - moved Install-Hlp for primary installation
;	01/20/98	John Hardesty - added comment to describe help file
;	01/21/98	John Hardesty - moved option check to allow cancel
;	04/09/98	Changed MediaType to mean ConnectionType & added MediaType.
;       10/06/99        Adding support for 9438TX
;----------------------------------------------------------------------------------------

[Identification]
    OptionType = NetAdapter

[PlatformsSupported]
    ISA
    EISA
    "Jazz-Internal Bus"
    PCI

[Options]
    SMC9432TX
    SMC9434TX
    SMC9438TX
    SMC9432BTX
    SMC9432FTX

[ConnectionChoicesSMC9432TX]
    Connect_0 = "Auto", 0
;    Connect_1 = "BNC 10 Mbps", 1
    Connect_2 = "UTP 10 Mbps", 2
    Connect_3 = "UTP 10 Mbps Full Duplex", 3
    Connect_4 = "UTP 100 Mbps TX", 4
    Connect_5 = "UTP 100 Mbps TX Full Duplex", 5
;    Connect_6 = "FIBER 100 Mbps Half Duplex", 6
;    Connect_7 = "FIBER 100 Mbps Full Duplex", 7

[ConnectionChoicesSMC9434TX]
    Connect_0 = "Auto", 0
;    Connect_1 = "BNC 10 Mbps", 1
    Connect_2 = "UTP 10 Mbps", 2
    Connect_3 = "UTP 10 Mbps Full Duplex", 3
    Connect_4 = "UTP 100 Mbps TX", 4
    Connect_5 = "UTP 100 Mbps TX Full Duplex", 5
;    Connect_6 = "FIBER 100 Mbps Half Duplex", 6
;    Connect_7 = "FIBER 100 Mbps Full Duplex", 7

[ConnectionChoicesSMC9438TX]
    Connect_0 = "Auto", 0
;    Connect_1 = "BNC 10 Mbps", 1
    Connect_2 = "UTP 10 Mbps", 2
    Connect_3 = "UTP 10 Mbps Full Duplex", 3
    Connect_4 = "UTP 100 Mbps TX", 4
    Connect_5 = "UTP 100 Mbps TX Full Duplex", 5
;    Connect_6 = "FIBER 100 Mbps Half Duplex", 6
;    Connect_7 = "FIBER 100 Mbps Full Duplex", 7

[ConnectionChoicesSMC9432BTX]
    Connect_0 = "Auto", 0
    Connect_1 = "BNC 10 Mbps", 1
    Connect_2 = "UTP 10 Mbps", 2
    Connect_3 = "UTP 10 Mbps Full Duplex", 3
    Connect_4 = "UTP 100 Mbps TX", 4
    Connect_5 = "UTP 100 Mbps TX Full Duplex", 5
;    Connect_6 = "FIBER 100 Mbps Half Duplex", 6
;    Connect_7 = "FIBER 100 Mbps Full Duplex", 7

[ConnectionChoicesSMC9432FTX]
    Connect_0 = "Auto", 0
;    Connect_1 = "BNC 10 Mbps", 1
    Connect_2 = "UTP 10 Mbps", 2
    Connect_3 = "UTP 10 Mbps Full Duplex", 3
    Connect_4 = "UTP 100 Mbps TX", 4
    Connect_5 = "UTP 100 Mbps TX Full Duplex", 5
    Connect_6 = "FIBER 100 Mbps Half Duplex", 6
    Connect_7 = "FIBER 100 Mbps Full Duplex", 7


[OptionsTextENG]
    SMC9432TX = "SMC9432TX EtherPower II 10/100 Ethernet Adapter"
    SMC9434TX = "SMC9434TX EtherPower II 10/100 Ethernet Adapter"
    SMC9438TX = "SMC9438TX EtherPower II 10/100 Ethernet Adapter"
    SMC9432BTX = "SMC9432BTX EtherPower II 10/100 Ethernet Adapter"
    SMC9432FTX = "SMC9432FTX EtherPower II 10/100 Ethernet Adapter"

[FileConstantsENG]
	ProCaption   = "Windows NT Setup"
	ProCancel    = "Cancel"
	ProCancelMsg = "Windows NT Networking is not correctly installed.  "+
		       "Are you sure you want to cancel copying files?"
	ProCancelCap = "Network Setup Message"
	ProText1     = "Copying:"
	ProText2     = "To:"

	ProductSoftwareDescription  = "SMC EtherPower II 10/100 Ethernet NDIS Driver"

	FunctionSMC9432TXTitle = "SMC9432TX EtherPower II 10/100 Ethernet Adapter Setup"
	ProductHardwareSMC9432TXDescription   = "SMC9432TX EtherPower II 10/100 Ethernet Adapter"

	FunctionSMC9434TXTitle = "SMC9434TX EtherPower II 10/100 Ethernet Adapter Setup"
	ProductHardwareSMC9434TXDescription   = "SMC9434TX EtherPower II 10/100 Ethernet Adapter"

	FunctionSMC9438TXTitle = "SMC9438TX EtherPower II 10/100 Ethernet Adapter Setup"
	ProductHardwareSMC9438TXDescription   = "SMC9438TX EtherPower II 10/100 Ethernet Adapter"

	FunctionSMC9432BTXTitle = "SMC9432BTX EtherPower II 10/100 Ethernet Adapter Setup"
	ProductHardwareSMC9432BTXDescription   = "SMC9432BTX EtherPower II 10/100 Ethernet Adapter"

	FunctionSMC9432FTXTitle = "SMC9432FTX EtherPower II 10/100 Ethernet Adapter Setup"
	ProductHardwareSMC9432FTXDescription   = "SMC9432FTX EtherPower II 10/100 Ethernet Adapter"

	ConnectionList  = ^(ConnectionChoices$(Option), 1)
	ConnectionValues = ^(ConnectionChoices$(Option), 2)
	NoList  = ^(NoChoices, 1)
	NoValues = ^(NoChoices, 2)
	ShellCodeErrorTitle     = "Error: "$(Function$(Option)Title)
	ShellCodeErrorText      = "Shell Code Error."
	CANNOT_FIND_ANY_CARD    = "Network card is not present in the system"

[DialogConstantsENG]
	Help        = "&Help"
	Exit        = "Cancel"
	OK          = "OK"
	HelpContext = ""
	Continue    = "Continue"
	Cancel      = "Cancel"

[FileDependentDlgENG]
	DlgText = "Choose the proper cable type for the "+
		  "network adapter. Select [Help] for a complete "+
		  "description of the available options of the list."
	DlgTemplate = "ADAP_PROTO_COMBO"
	DlgType = "Combination"
	Caption = $(Function$(Option)Title)
	Combo1Label = "&Media Type"
	Combo1List = $(ConnectionList)
	Combo1Out  = $(ConnectionValue)
	ComboListItemsIn  = {Combo1List}
	ComboListItemsOut = {Combo1Out}
	EditTextLim = ""
	CBOptionsGreyed = {}
	MinHelpId = 10
	MaxHelpId = 1140

; jch
; This resolves to "HelpSMC9432TXId" which is set equal to 30 below
; 30 MUST be the context id of the CONTENTS section of the help file
	HelpContext = $(Help$(Option)Id)

[FileConstantsEpic]
	UtilityInf      = "UTILITY.INF"
	subroutineinf   = "SUBROUTN.INF"
	SoftwareType    = "driver"
	Exit_Code       = 0
	NetEventDLL     = "%SystemRoot%\System32\netevent.dll"
	IoLogMsgDLL     = "%SystemRoot%\System32\IoLogMsg.dll"
	Manufacturer    = "StandardMicrosystemsCorporation"
	ProductMajorVersion     = "2"
	ProductMinorVersion     = "41"
	ProductVersion  = $(ProductMajorVersion)"."$(ProductMinorVersion)

	VendorID = 4280  ;; 10b8 (SMC)

	ProductSoftwareName     = "smcpwr2n"
	ProductSoftwareTitle    = "SMC EtherPower II 10/100 Ethernet NDIS Driver"
	ProductSoftwareImagePath = "\SystemRoot\System32\drivers\smcpwr2n.sys"
	NetRuleSoftwareType     = "Smcpwr2nSys ndisDriver Smcpwr2nDriver"
	NetRuleSoftwareUse      = $(SoftwareType)
	NetRuleSoftwareBindForm = """Smcpwr2nSys"" yes no container"
	NetRuleSoftwareClass    = {"Smcpwr2nDriver basic"}
	NetRuleSoftwareSWBindable = {+
				     "Smcpwr2nDriver Smcpwr2nAdapter non exclusive 100"}
	ProductHardwareName     = "smcpwr2n"

	ProductHardwareSMC9432TXTitle   = "SMC9432TX EtherPower II 10/100 Ethernet Adapter"
	NetRuleHardwareSMC9432TXType    = "Smcpwr2n Smcpwr2nAdapter"
	NetRuleHardwareSMC9432TXClass   = {"Smcpwr2nAdapter basic"}
	AdapterSMC9432TXType = 5  ;; PCI board
	HelpSMC9432TXId  = 30    ; jch See note above about this value and relationship to smcpwr2.hlp
	SMC9432TXCFID = 331960    ;; 0x510b8
    OptionHelpFile = "smcpwr2.hlp"

	ProductHardwareSMC9434TXTitle   = "SMC9434TX EtherPower II 10/100 Ethernet Adapter"
	NetRuleHardwareSMC9434TXType    = "Smcpwr2n Smcpwr2nAdapter"
	NetRuleHardwareSMC9434TXClass   = {"Smcpwr2nAdapter basic"}
	AdapterSMC9434TXType = 5  ;; PCI board
	HelpSMC9434TXId  = 30    ; jch See note above about this value and relationship to smcpwr2.hlp
	SMC9434TXCFID = 331960    ;; 0x510b8
    OptionHelpFile = "smcpwr2.hlp"

	ProductHardwareSMC9438TXTitle   = "SMC9438TX EtherPower II 10/100 Ethernet Adapter"
	NetRuleHardwareSMC9438TXType    = "Smcpwr2n Smcpwr2nAdapter"
	NetRuleHardwareSMC9438TXClass   = {"Smcpwr2nAdapter basic"}
	AdapterSMC9438TXType = 5  ;; PCI board
	HelpSMC9438TXId  = 30    ; jch See note above about this value and relationship to smcpwr2.hlp
	SMC9438TXCFID = 331960    ;; 0x510b8
    OptionHelpFile = "smcpwr2.hlp"

	ProductHardwareSMC9432BTXTitle   = "SMC9432BTX EtherPower II 10/100 Ethernet Adapter"
	NetRuleHardwareSMC9432BTXType    = "Smcpwr2n Smcpwr2nAdapter"
	NetRuleHardwareSMC9432BTXClass   = {"Smcpwr2nAdapter basic"}
	AdapterSMC9432BTXType = 5  ;; PCI board
	HelpSMC9432BTXId  = 30    ; jch See note above about this value and relationship to smcpwr2.hlp
	SMC9432BTXCFID = 331960    ;; 0x510b8
    OptionHelpFile = "smcpwr2.hlp"

	ProductHardwareSMC9432FTXTitle   = "SMC9432FTX EtherPower II 10/100 Ethernet Adapter"
	NetRuleHardwareSMC9432FTXType    = "Smcpwr2n Smcpwr2nAdapter"
	NetRuleHardwareSMC9432FTXClass   = {"Smcpwr2nAdapter basic"}
	AdapterSMC9432FTXType = 5  ;; PCI board
	HelpSMC9432FTXId  = 30    ; jch See note above about this value and relationship to smcpwr2.hlp
	SMC9432FTXCFID = 331960    ;; 0x510b8
    OptionHelpFile = "smcpwr2.hlp"

	NetRuleHardwareBindForm = " yes yes container"
	ProductKeyName  = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion"
	ParamKeyName    = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters"

[GeneralConstants]
	from      = ""
	to        = ""
	ExitCodeOk     = 0
	ExitCodeCancel = 1
	ExitCodeFatal  = 2
	KeyNull         = ""
	MAXIMUM_ALLOWED   = 33554432
	RegistryErrorIndex = NO_ERROR
	KeyProduct      = ""
	KeyParameters   = ""
	TRUE            = 1
	FALSE           = 0
	NoTitle            = 0
	ExitState   = "Active"
	OldVersionExisted = $(FALSE)
	DriverPath      = $(!STF_NTPATH)\drivers

[date]
    Now = {} ? $(!LIBHANDLE) GetSystemDate

[Identify]
    set !DebugOutputControl = 1
    Debug-Output "SMCINF-[Identify]"
    read-syms Identification
    set Status     = STATUS_SUCCESSFUL
    set Identifier = $(OptionType)
    set Media      = #("Source Media Descriptions", 1, 1)
    Return $(Status) $(Identifier) $(Media)

[ReturnOptions]
    set !DebugOutputControl = 1
    Debug-Output "SMCINF-[ReturnOptions]"
    set Status        = STATUS_FAILED
    set OptionList     = {}
    set OptionTextList = {}
    set LanguageList = ^(LanguagesSupported, 1)

     Ifcontains(i) $($0) in $(LanguageList)
		ifstr(i) $($1) == ""
		   goto returnoptions
		endif
		set PlatformList = ^(PlatformsSupported, 1)
		Ifcontains(i) $($1) in $(PlatformList)
		   goto returnoptions
		else
		   set Status = STATUS_NOTSUPPORTED
		   goto finish_ReturnOptions
		endif
    else
		set Status = STATUS_NOLANGUAGE
		goto finish_ReturnOptions
    endif

returnoptions = +

    set OptionList     = ^(Options, 1)
    set OptionTextList = ^(OptionsText$($0), 1)
    set Status         = STATUS_SUCCESSFUL

finish_ReturnOptions = +

    Return $(Status) $(OptionList) $(OptionTextList)

[InstallOption]
    set !DebugOutputControl = 1
    Debug-Output "SMCINF-[InstallOption]"
    set Option   = $($1)
    set SrcDir   = $($2)
    set AddCopy  = $($3)
    set DoCopy   = $($4)
    set DoConfig = $($5)
    set LanguageList = ^(LanguagesSupported, 1)


    Ifcontains(i) $($0) NOT-IN $(LanguageList)
		Return STATUS_NOLANGUAGE
    endif

    set-subst LF = "//n"
    read-syms GeneralConstants
    read-syms FileConstantsEpic

    set NetRuleSoftwareBindable = $($R1)

    read-syms DialogConstants$(!STF_LANGUAGE)

    ifstr(i) $(!NTN_Origination) == "NCPA"
		set Continue = "OK"
    endif

    read-syms FileConstants$(!STF_LANGUAGE)
    detect date
    set-title  $(Function$(Option)Title)
    set to   = Begin
    set from = Begin
    set CommonStatus = STATUS_SUCCESSFUL
    EndWait

Begin = +

    Ifstr(i) $(!NTN_InstallMode) == deinstall
		set StartLabel = removeadapter
    else-Ifstr(i) $(!NTN_InstallMode) == Update
		set StartLabel = UpgradeSoftware
    else-Ifstr(i) $(!NTN_InstallMode) == bind
		set StartLabel = bindingadapter
    else-Ifstr(i) $(!NTN_InstallMode) == configure
		Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
	       Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE
	       ifint $($ShellCode) != $(!SHELL_CODE_OK)
		     goto ShellCodeError
	       endif
	       set Error = $($R0)
	       set from = end
	       set to = end
	       goto nonfatalinfo
		else
	       set StartLabel = configureadapter
		endif
	else
		set StartLabel = installadapter
		set OEM_ABANDON_OPTIONS = {}
		set OEM_ABANDON_SOFTWARE = FALSE
		set OEM_ABANDON_ON = TRUE
    endif

    set from = $(fatal)
    set to = $(fatal)
    goto $(StartLabel)

installadapter = +

    OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct

    Ifstr $(KeyProduct) != $(KeyNull)
		CloseRegKey $(KeyProduct)
		ifstr(i) !(NTN_RegBase) == $(ProductKeyName)
		   Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+
		       $(ProductVersion)
		   ifint $($ShellCode) != $(!SHELL_CODE_OK)
		       goto ShellCodeError
		   endif
		   goto end
		else
		   Shell $(UtilityInf), CardExistedDlg
		   ifint $($ShellCode) != $(!SHELL_CODE_OK)
		      goto ShellCodeError
		   endif
		   ifstr(i) $($R1) != "OK"
		       set CommonStatus = STATUS_USERCANCEL
		       goto end
		   endif
		   set OldVersionExisted = $(TRUE)
		endif
    Endif

    ifstr(i) $(DoCopy) == "YES"
		Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES
		Ifint $($ShellCode) != $(!SHELL_CODE_OK)
		    Goto ShellCodeError
		Else-Ifstr(i) $($R0) == STATUS_FAILED
		    Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
		    ifint $($ShellCode) != $(!SHELL_CODE_OK)
		       goto ShellCodeError
		    endif
		    set Error = $($R0)
		       Goto fatal
		Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
		       Goto successful
		Endif
		Set SrcDir = $($R1)
		install "Install-Hlp"
    endif
    Goto installproduct

configureadapter = +

	Ifstr(i) $(KeyProduct) == $(KeyNull)
		OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct
		Ifstr $(KeyProduct) == $(KeyNull)
		    Set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
		   Goto fatalregistry
		Endif
    Endif

    Shell $(UtilityInf) FindService, $(KeyProduct)
    Ifint $($ShellCode) != $(!SHELL_CODE_OK)
		Goto ShellCodeError
    Endif

    Ifstr(i) $($R0) != NO_ERROR
		Goto fatalregistry
    endif

    set KeyParameters = $($R2)
    CloseRegKey $($R1)
    Ifstr $(KeyParameters) == $(KeyNull)
		set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
		goto fatalregistry
    endif

    set OldVersionExisted = $(TRUE)
    set ValueName = ""
    set ValueData = ""
    set ValueStr  = ""
    set ValueList = {}

    EnumRegValue $(KeyParameters) ValueList

    ForListDo $(ValueList)
		set ValueItem = $($)
		set ValueName = *($(ValueItem),1)
		set ValueData = *($(ValueItem),4)
		Ifstr(i) $(ValueName) == "ConnectionType"
		    set ConnectionIndex = $(ValueData)
		endif
    EndForListDo

    set ConnectionValue = *($(ConnectionList), ~($(ConnectionValues),$(ConnectionIndex)))
    ifstr(i) $(ConnectionValue) == ""
		set ConnectionValue = *($(ConnectionList), 2)
    endif

adapteroptions = +

	set from = adapteroptions
	read-syms FileDependentDlg$(!STF_LANGUAGE)

	SetHelpFile $(!STF_WINDOWSSYSPATH)"\"$(OptionHelpFile) $(MinHelpId) $(MaxHelpId) $(Help$(Option)Id)

	ui start "InputDlg"
	ifstr(i) $(DLGEVENT) == "CONTINUE"
	   set ConnectionIndex = $(Combo1Out)
	   ui pop 1
	else-ifstr(i) $(DLGEVENT) == "BACK"
	   set CommonStatus = STATUS_USERCANCEL
	   ui pop 1
	   goto end
	else
	   ui pop 1
	   goto end
	endif

	set ConnectionValue = *($(ConnectionValues), ~($(ConnectionList),$(ConnectionIndex)))
	ifstr(i) $(!NTN_InstallMode) == configure
	   goto updateparameters
	endif

installproduct =+

    StartWait
	set-div DeviceID = $($(Option)CFID) 65336
	Shell $(UtilityInf), GetPCIInformation, $(VendorID) $(DeviceID)
	ifint $($ShellCode) != $(!SHELL_CODE_OK)
	     goto ShellCodeError
	endif
	ifstr(i) $($R0) == {}
	     set Error = $(CANNOT_FIND_ANY_CARD)
	     set CommonStatus = USER_CANCEL
	     set from = end
	     goto nonfatal
	endif

	set AdapterList = $($R0)

    ifint $(OldVersionExisted) == $(FALSE)
		Ifstr(i) $(DoCopy) == "YES"
		   Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES
		   Ifint $($ShellCode) != $(!SHELL_CODE_OK)
		       Goto ShellCodeError
		   Else-Ifstr(i) $($R0) == STATUS_FAILED
		       Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
		       ifint $($ShellCode) != $(!SHELL_CODE_OK)
				  goto ShellCodeError
		       endif
		       set Error = $($R0)
		       Goto fatal
		   Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
		       Goto successful
		   Endif
		   Set SrcDir = $($R1)
		Endif

		install "Install-Hlp"

; The following code was moved up from below to fix a problem with cancel
; during primary installation
; - start -
        ifstr(i) $(!STF_GUI_UNATTENDED) != "YES"
            read-syms FileDependentDlg$(!STF_LANGUAGE)
            SetHelpFile $(!STF_WINDOWSSYSPATH)"\"$(OptionHelpFile) $(MinHelpId) $(MaxHelpId) $(Help$(Option)Id)

            ui start "InputDlg"

            ifstr(i) $(DLGEVENT) == "CONTINUE"
                set ConnectionIndex = $(Combo1Out)
                ui pop 1
            else-ifstr(i) $(DLGEVENT) == "BACK"
                set CommonStatus = STATUS_USERCANCEL
                ui pop 1
                goto end
            else
                ui pop 1
                goto end
            endif
        endif

; - end -

		install "Install-Option"
		ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
		   Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE"
		   ifint $($ShellCode) != $(!SHELL_CODE_OK)
		       goto ShellCodeError
		   endif
		   set Error = $($R0)
		   goto fatal
		endif

		Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
		    $(ProductSoftwareName), +
		    $(ProductSoftwareName), +
		    $(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), +
		    $(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+
		    $(NetEventDLL)

		Set OEM_ABANDON_SOFTWARE = TRUE

		ifint $($ShellCode) != $(!SHELL_CODE_OK)
		    goto ShellCodeError
		endif

		set RegistryErrorIndex = $($R0)

		Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
		    EndWait
		    CloseRegKey $($R1)
		    CloseRegKey $($R2)
		    CloseRegKey $($R3)
		    CloseRegKey $($R4)
		    CloseRegKey $($R5)
		    goto fatalregistry
		endif

		Set SoftProductKey      = $($R1)
		Set SoftNetRuleKey      = $($R2)
		Set SoftServiceKey      = $($R3)
		Set SoftParameterKey    = $($R4)
		Set SoftLinkageKey      = $($R5)

		set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+
				   {MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+
				   {MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+
				   {Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+
				   {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+
				   {ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+
				   {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}

		Shell  $(UtilityInf), AddValueList, $(SoftProductKey), $(NewValueList)

		ifint $($ShellCode) != $(!SHELL_CODE_OK)
		    goto ShellCodeError
		endif

		set RegistryErrorIndex = $($R0)

		Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
		    EndWait
		    CloseRegKey $(SoftProductKey)
		    CloseRegKey $(SoftNetRuleKey)
		    CloseRegKey $(SoftServiceKey)
		    CloseRegKey $(SoftParameterKey)
		    CloseRegKey $(SoftLinkageKey)
		    goto fatalregistry
		endif

		set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+
				    {use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, +
				    {bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, +
				    {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, +
				    {bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareSWBindable)}, +
				    {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}

		Shell  $(UtilityInf), AddValueList, $(SoftNetRuleKey), $(NewValueList)

		ifint $($ShellCode) != $(!SHELL_CODE_OK)
		    goto ShellCodeError

		endif

		set RegistryErrorIndex = $($R0)
		CloseRegKey $(SoftProductKey)
		CloseRegKey $(SoftNetRuleKey)
		CloseRegKey $(SoftServiceKey)
		CloseRegKey $(SoftParameterKey)
		CloseRegKey $(SoftLinkageKey)

		Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
		    EndWait
		    goto fatalregistry
		endif

    endif

    ForListDo $(AdapterList)
		set BusNum = *($($),1)
		set DeviceNum = *($($),2)
		set FunctionNum = *($($),3)

		Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(BusNum), +
		    $(DeviceNum), $(ProductHardware$(Option)Description), $(ProductHardwareName) "YES"

		ifint $($ShellCode) != $(!SHELL_CODE_OK)
		    goto ShellCodeError
		endif

		ifstr $($R0) != "NO_ERROR"
		    set Error = $($R0)
		    goto fatal
		endif

		ifstr(i) $($R1) != "YES"
		    Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)

		    ifint $($R4) != -1
				Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
		    endif
		    ifint $($ShellCode) != $(!SHELL_CODE_OK)
				goto ShellCodeError
		    endif

		    set RegistryErrorIndex = $($R0)

		    Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
				EndWait
				CloseRegKey $($R1)
				CloseRegKey $($R2)
				CloseRegKey $($R3)
				goto fatalregistry
		    endif

		    set ConnectionValue = *($(ConnectionValues), ~($(ConnectionList),$(ConnectionIndex)))
		    Set HardNetCardKey      = $($R1)
		    Set HardNetRuleKey      = $($R2)
		    Set HardParameterKey    = $($R3)
		    set AdapterNumber = $($R4)

		    set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+
					{Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+
					{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+
					{ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
					{ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+
					{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}

		    Shell  $(UtilityInf), AddValueList, $(HardNetCardKey), $(NewValueList)

		    ifint $($ShellCode) != $(!SHELL_CODE_OK)
				goto ShellCodeError
		    endif

		    set BusTypeNum = 5

            set NewValueList = { +
                { AdapterType,      $(NoTitle), $(!REG_VT_DWORD),   $(Adapter$(Option)Type) }, +
                { BusType,          $(NoTitle), $(!REG_VT_DWORD),   $(BusTypeNum) }, +
                { AdapterCFID,      $(NoTitle), $(!REG_VT_DWORD),   $($(Option)CFID) }, +
                { ConnectionType,   $(NoTitle), $(!REG_VT_DWORD),   $(ConnectionValue) }, +
                { IpgDelay,         $(NoTitle), $(!REG_VT_DWORD),   0 }, +
                { PowerMode,        $(NoTitle), $(!REG_VT_DWORD),   0 }, +
                { BurstLength,      $(NoTitle), $(!REG_VT_DWORD),   8 }, +
                { ScrambleOn,       $(NoTitle), $(!REG_VT_DWORD),   0 }, +
                { TxPacketDesc,     $(NoTitle), $(!REG_VT_DWORD),   50 }, +
                { RxPacketDesc,     $(NoTitle), $(!REG_VT_DWORD),   120 }, +
                { TxDmaDesc,        $(NoTitle), $(!REG_VT_DWORD),   29 }, +
                { RxDmaDesc,        $(NoTitle), $(!REG_VT_DWORD),   40 }, +
                { PacketsPerTxInt,  $(NoTitle), $(!REG_VT_DWORD),   10 }, +
                { PacketsPerRxInd,  $(NoTitle), $(!REG_VT_DWORD),   10 }, +
                { IpgTimer,         $(NoTitle), $(!REG_VT_DWORD),   15456 }, +
                { SlotTimer,        $(NoTitle), $(!REG_VT_DWORD),   120 }, +
				{ MediaType,		$(NoTitle), $(!REG_VT_DWORD),	1}, +
                { GenControl,       $(NoTitle), $(!REG_VT_DWORD),   3344 }}

		    Shell  $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)

		    ifint $($ShellCode) != $(!SHELL_CODE_OK)
				goto ShellCodeError
		    endif

		    ifint $($(Option)CFID) == $(DC21041CFID)

				set NewValueList = {{SnoozeMode,$(NoTitle),$(!REG_VT_DWORD),0}}

				Shell  $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
				ifint $($ShellCode) != $(!SHELL_CODE_OK)
				    goto ShellCodeError
				endif
		    endif

		    ifint $($(Option)CFID) == $(DC21140CFID)

				set NewValueList = {{StoreAndForward,$(NoTitle),$(!REG_VT_DWORD),1},+
						    {TransmitThreshold,$(NoTitle),$(!REG_VT_DWORD),512}}

				Shell  $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)

				ifint $($ShellCode) != $(!SHELL_CODE_OK)
				    goto ShellCodeError
				endif
		    endif

		    Shell  $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)

		    ifint $($ShellCode) != $(!SHELL_CODE_OK)
				goto ShellCodeError
		    endif

		    set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
		    set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)

		    set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardware$(Option)Type)},+
					{bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
					{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardware$(Option)Class)}, +
					{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}

		    Shell  $(UtilityInf), AddValueList, $(HardNetRuleKey), $(NewValueList)

		    ifint $($ShellCode) != $(!SHELL_CODE_OK)
				goto ShellCodeError
		    endif

		    CloseRegKey $(HardNetCardKey)
		    CloseRegKey $(HardNetRuleKey)

		    set NewValueList = {{BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNum)},+
					{SlotNumber,$(NoTitle),$(!REG_VT_DWORD),$(DeviceNum)},+
					{FunctionNumber,$(NoTitle),$(!REG_VT_DWORD),$(FunctionNum)}}

		    Shell  $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)

            ifstr(i) $(!STF_GUI_UNATTENDED) == "YES"
                Shell $(UtilityInf),AddDefaultNetCardParameters,$(HardParameterKey)
            endif

		    CloseRegKey $(HardParameterKey)

		endif

    EndForListDo

    EndWait
    goto successful

updateparameters =+

    set HardParameterKey    = $($R3)

    set NewValueList = {{ConnectionType,$(NoTitle),$(!REG_VT_DWORD),$(ConnectionValue)}}

    Shell  $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)

    ifint $($ShellCode) != $(!SHELL_CODE_OK)
		goto ShellCodeError
    endif

    CloseRegKey $(KeyParameters)
    goto successful

bindingadapter =+

    set Error = "Binding: Sorry, not yet implemented."
    goto fatal

removeadapter = +

    Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
		Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
		    $(ProductSoftwareName)
		ifint $($ShellCode) != $(!SHELL_CODE_OK)
		    goto ShellCodeError
		endif
		set RegistryErrorIndex = $($R0)
		Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
		    goto fatalregistry
		endif
    else
		Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
		    $(ProductSoftwareName), $(!NTN_RegBase)
		ifint $($ShellCode) != $(!SHELL_CODE_OK)
		    goto ShellCodeError
		endif
		set RegistryErrorIndex = $($R0)
		Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
		    goto fatalregistry
		endif
    endif
    goto end

UpgradeSoftware = +

     OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
     Ifstr $(KeyProduct) != $(KeyNull)
	   Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct)
	   ifint $($ShellCode) != $(!SHELL_CODE_OK)
    	   set !DebugOutputControl = 1
	       Debug-Output "ShellCode error"
	       goto ShellCodeError
	   endif

	   set !UG_Filename = $($R0)

	   install "Install-Update"
	   ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
	       goto fatal
	   endif

	   SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)}
	   SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)}
	   CloseRegKey $(KeyProduct)
     else
	   goto fatalregistry
     endif
     goto end

successful = +

    set !DebugOutputControl = 1
	Debug-Output "SMCINF- successful-"

    goto end

abandon = +

    set !DebugOutputControl = 1
	Debug-Output "SMCINF- abandon-"

    ForListDo $(OEM_ABANDON_OPTIONS)
		Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
		    $(ProductSoftwareName), $($)
		ifint $($ShellCode) != $(!SHELL_CODE_OK)
		    goto ShellCodeError
		endif
		set RegistryErrorIndex = $($R0)
		Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
		    goto fatalregistry
		endif
    EndForListDo

    Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE
		Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
		    $(ProductSoftwareName), FALSE
		ifint $($ShellCode) != $(!SHELL_CODE_OK)
		    goto ShellCodeError
		endif
		set RegistryErrorIndex = $($R0)
		Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
		    goto fatalregistry
		endif
    endif
    goto end

warning = +

    set !DebugOutputControl = 1
	Debug-Output "SMCINF- warning-"

    Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error)

    ifint $($ShellCode) != $(!SHELL_CODE_OK)
		goto ShellCodeError
    endif

    ifstr(i) $($R1) == "OK"
		goto $(to)
    else-ifstr(i) $($R1) == "CANCEL"
		goto $(from)
    else
		goto "end"
    endif

nonfatalinfo = +

    set !DebugOutputControl = 1
	Debug-Output "SMCINF- nonfatalinfo-"

    Set CommonStatus = STATUS_USERCANCEL
    Set Severity = STATUS
    goto nonfatalmsg

nonfatal = +

    set !DebugOutputControl = 1
	Debug-Output "SMCINF- nonfatal-"

    Set Severity = NONFATAL
    goto nonfatalmsg

nonfatalmsg = +

    set !DebugOutputControl = 1
	Debug-Output "SMCINF- nonfatalmsg-"

    ifstr(i) $(Error) == ""
		Set Severity = NONFATAL
		Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
		ifint $($ShellCode) != $(!SHELL_CODE_OK)
		    goto ShellCodeError
		endif
		set Error = $($R0)
    endif

    Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)

    ifint $($ShellCode) != $(!SHELL_CODE_OK)
		goto ShellCodeError
    endif
    ifstr(i) $($R1) == "OK"
		goto $(from)
    else
		goto "end"
    endif

fatalregistry = +

    set !DebugOutputControl = 1
	Debug-Output "SMCINF- fatalregistry-"

    Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
		goto ShellCodeError
    endif
    set Error = $($R0)
    goto fatal

fatal = +

    set !DebugOutputControl = 1
	Debug-Output "SMCINF- fatal-"

    ifstr(i) $(Error) == ""
		Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
		ifint $($ShellCode) != $(!SHELL_CODE_OK)
		    goto ShellCodeError
		endif
		set Error = $($R0)
    endif
    Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error)
    ifint $($ShellCode) != $(!SHELL_CODE_OK)
		goto ShellCodeError
    endif
    goto setfailed

ShellCodeError = +

    set !DebugOutputControl = 1
	Debug-Output "SMCINF- ShellCodeError-"

    set DlgType      = "MessageBox"
    set STF_MB_TITLE = $(ShellCodeErrorTitle)
    set STF_MB_TEXT  = $(ShellCodeErrorText)
    set STF_MB_TYPE  = 1
    set STF_MB_ICON  = 3
    set STF_MB_DEF   = 1

    ui start "Error Message"

    goto setfailed

setfailed = +

    set !DebugOutputControl = 1
	Debug-Output "SMCINF- setfailed-"

    set CommonStatus = STATUS_FAILED
    ifstr(i) $(OEM_ABANDON_ON) == TRUE
		set OEM_ABANDON_ON = FALSE
		goto abandon
    endif
    goto end

end = +

    set !DebugOutputControl = 1
	Debug-Output "SMCINF- end-"

    goto term

term = +

    set !DebugOutputControl = 1
	Debug-Output "SMCINF- term-"

    Return $(CommonStatus)

[Install-Option]

    set !DebugOutputControl = 1
	Debug-Output "SMCINF- [Install-Option]-"

    set STF_VITAL = ""
    ifstr(i) $(AddCopy) == "YES"
		AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
    endif
    ifstr(i) $(DoCopy) == "YES"
       set !STF_NCPA_FLUSH_COPYLIST = TRUE
       CopyFilesInCopyList
    endif
    Exit

[Install-Hlp]

    set !DebugOutputControl = 1
	Debug-Output "SMCINF- [Install-Hlp]-"

   set STF_VITAL = ""
   AddSectionFilesToCopyList Files-Hlp $(SrcDir) $(!STF_WINDOWSSYSPATH)
   set !STF_NCPA_FLUSH_COPYLIST = TRUE
   CopyFilesInCopyList
   Exit

[Install-Update]

    set !DebugOutputControl = 1
	Debug-Output "SMCINF- [Install-Update]-"

   set STF_VITAL        = ""
   set STF_OVERWRITE    = "VERIFYSOURCEOLDER"
   AddSectionFilesToCopyList Files-Hlp $(SrcDir) $(!STF_WINDOWSSYSPATH)
   AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH)
   AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
   set !STF_NCPA_FLUSH_COPYLIST = TRUE
   CopyFilesInCopyList
   exit

[Source Media Descriptions]
    1  = "SMC SuperDisk"

[ProductType]

    set !DebugOutputControl = 1
	Debug-Output "SMCINF- [ProductType]-"

	STF_PRODUCT  = Winnt
	STF_PLATFORM = I386

[Files-Inf]
    2, oemsetup.inf, SIZE=1000, RENAME=$(!UG_Filename)

[Files-SMC9432TX]
    1, smcpwr2n.sys, SIZE=999,	RENAME=smcpwr2n.sys

[Files-SMC9434TX]
    1, smcpwr2n.sys, SIZE=999,	RENAME=smcpwr2n.sys

[Files-SMC9438TX]
    1, smcpwr2n.sys, SIZE=999,	RENAME=smcpwr2n.sys

[Files-SMC9432BTX]
    1, smcpwr2n.sys, SIZE=999,	RENAME=smcpwr2n.sys

[Files-SMC9432FTX]
    1, smcpwr2n.sys, SIZE=999,	RENAME=smcpwr2n.sys

[Files-Hlp]
    1, smcpwr2.hlp, SIZE=999,   RENAME=smcpwr2.hlp

[LanguagesSupported]
    ENG

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: ftp, load: 2.69