.TOPIC:
Contents
STANDARD MICROSYSTEMS CORPORATION
SMC EZ Card 10 Ethernet ISA Network Cards
Microsoft Windows for Workgroups v3.11 Driver
For Ethernet LAN Cards
INSTALLATION GUIDE
This software is licensed by SMC for use by its customers only.
Copyright (c) 1996 Standard Microsystems Corporation.
All rights reserved.
SUPPORTED NETWORK CARDS
SMC EZ Card 10 Ethernet ISA Network Cards:
o SMC1660T
o SMC1660BT
o SMC1660BTA
Content:
A) SMC Support Drivers for WFW 3.11
B) Install NDIS 2.0/ NDIS 3.0 Driver for WFW 3.11
C) Install ODI/ NDIS 3.0 Driver for WFW 3.11
A) SMC Support Drivers for WFW 3.11
SMC supports NDIS 2.0, NDIS 3.0 and DOS/ODI drivers for Windows
for Workgroups 3.11. A description of these 3 files are as follows:
Driver Name Location Description
SMC1660W.SYS A:\WFW311 NDIS 3.0 driver in enhanced mode
SMC1660.DOS A:\NDIS\DOS NDIS 2.0 driver in real mode
SMC1660.COM A:\DOS SMC EZ Card 10 ISA DOS/ODI driver
B) Install NDIS 2.0/ NDIS 3.0 Driver for WFW 3.11
NOTE: If the card is set to Plug and Play mode, the default, do not change
the settings in the Setup Screen when installing the WFW 3.11 driver.
If the card is set to Jumperless mode, the settings in the Setup
screen will need to match the card's settings. You can run SMCINST
and select the Hardware Configuration option to see how card is set
before installing the driver.
1. Run Windows by typing "WIN" from the DOS prompt.
2. Click the "Network" icon in the Main Program Group.
3. Click the "Network Setup" icon from the Network window.
4. Check the drivers button. If it is hidden and cannot be selected,
go to the next step. If it is visible, go to step 8.
5. Click the "Networks" button
6. Select "Install Microsoft Windows Network," and then select
"No additional network."
7. Click the "OK" button
8. Select "Drivers" item from the "Network Setup" dialog box.
9. Select "Add Adapters." The "Add Network Adapter" dialog box
appears.
10. If:
a. You are installing this SMC network card for the first time,
select "Unlisted" or "Updated Network Adapter." Click "OK," then
go to step 11.
b. You have installed SMC's network card before, just select the
"SMC EZ Card ISA 10 driver" from the drivers list table and
go to step 12.
11. Insert the SMC Driver Diskette in floppy drive A or B, and
then type the destination drive and path name. Make sure the
full path of the directory (i.e., A:\WFW311) is given. Select "OK."
Then, you will see the "SMC EZ Card ISA 10 driver" dialog box
appear. Select "OK."
12. You will be prompted to confirm the I/O address and IRQ. If the
card is set to PNP mode, the default, do not change the settings.
If the card is set to Jumperless mode, the settings will need to
match the card's settings. You can run SMCINST and select the
Hardware Configuration option to see how the card is set. The
default settings are I/O 300, IRQ 10 when changing to Jumperless
from PNP mode. Select "OK."
13. When the Network Drivers window appears, you can use
"Add Adapter" and/or "Add Protocol" to add more
network cards (up to four) and protocols. Refer to your
Windows for Workgroups manual for more information.
o To change the Base I/O Port and/or driver type, select "Setup"
and make the appropriate selections.
o There are 4 drivers type:
. Real mode and Enhanced mode NDIS
. Enhanced mode NDIS
. Real mode NDIS
. ODI driver
You can select one of these 4 driver types depending on your
application. The default is Real and Enhanced mode.
o Select "Close" followed by "OK."
o When prompted with the "Microsoft Windows Networks Names" box,
select "OK."
o Follow the screen prompts to complete the driver installation.
Note: The "Install Driver" window will appear. You will be
prompted to insert the SMC Diskette. The driver's source
path is A:\WFW311.
14. At the end of the installation, you will be prompted
to accept all the options you selected and restart
your computer or to return to DOS. Restart your computer so
your options can take effect.
Some specifics of the installation process may vary according to
each user's needs. Refer to the Microsoft Windows for Workgroups
user manual for more information.
Following are some sample Configuration Files
--------------------------------------------
1. CONFIG.SYS File
FILES=30
BUFFERS=30
LASTDRIVE=Z
DEVICE=C:\windows\HIMEM.SYS
DEVICE=C:\windows\IFSHLP.SYS
STACKS=9,256
2. AUTOEXEC.BAT File
C:\windows\SMARTDRV.EXE
C:\windows\net start
PATH C:\windows;
SET TEMP=C:\windows\TEMP
3. PROTOCOL.INI File on Windows for Workgroups 3.11
[network.setup]
version=0x3110
netcard=ms$smc1660,1,MS$SMC1660,2
transport=ms$netbeui,NETBEUI
lana0=ms$smc1660,1,ms$netbeui
[MS$SMC1660]
DriverName=SMC1660W$
INTERRUPT=3
IOBASE=0x300
[SMC1660]
adapters=MS$SMC1660
[NETBEUI]
BINDINGS=MS$SMC1660
LANABASE=0
SESSIONS=10
NCBS=12
4. SYSTEM.INI
[386Enh]
netcard=SMC1660W.386
C) Install ODI/ NDIS 3.0 driver for WFW 3.11
You must make sure that the ODI driver is loaded first before you
install the Windows driver. If needed see readme.txt file in DOS
directory of this disk for installing the ODI driver.
1. Run Windows by typing "WIN" from the DOS prompt.
2. Click the "Network" icon in the Main Program Group.
3. Click the "Network Setup" icon from the Network window.
4. Check the drivers button. If it is hidden and can't be selected,
then go to the next step. If it is visible, you still need to go
to step 5 to set up a Novell shell.
5. Click the "Networks" button
6. Select "Install Microsoft Windows Network."
Select "Other" and then "Novell Netware Workstation Shell 4.0"
for VLM or "...Shell 3.x" for NETX.
7. Click the "OK" button
8. Select "Drivers" item from the "Network Setup" dialog box.
9. Select "Add Adapters." The "Add Network Adapter" dialog box
appears.
10. If:
a. You are installing an SMC EZ Card 10 for the first time, select
"Unlisted" or "Updated Network Adapter." Then, click "OK."
b. You have installed SMC's network card before, just select
"SMC EZ Card ISA 10 driver" from the drivers list table,
select "OK" and then go to step 12.
11. Insert the SMC Driver Diskette in floppy drive A or B,
then type the destination drive and path name. Make sure
the full path of the directory (i.e., A:\WFW311) is given.
Select "OK." Then, you will see the "SMC EZ Card ISA 10 driver"
dialog box appear. Select "OK."
12. When the Network Drivers window appears, you can use
"Add Adapter" and/or "Add Protocol" to add more
network cards (up to four) and protocols. Refer to your
Windows for Workgroups manual for more information.
Select "Setup" and make the appropriate selection.
There are 4 driver type:
. Real mode and Enhanced mode NDIS
. Enhanced mode NDIS
. Real mode NDIS
. ODI driver
YOU MUST SELECT THE ODI DRIVER TO LET THE NETWARE ODI
DRIVER WORK IN WFW 3.11.
Select "Close" followed by "OK."
13. When prompted with the "Microsoft Windows Networks Names"
box, select "OK."
Follow the screen prompts to complete the driver installation.
14. At the end of the installation, you will be prompted
to accept all the options you selected and restart
your computer or to return to DOS. Restart your computer so
your options can take effect.
Some specifics of the installation process may vary according to
each user's needs. Refer to the Microsoft Windows for Workgroups
user manual for more information.
NOTE: To connect to a Novell server from within Windows for Workgroups
make sure you are logged on to a NetWare server before starting
Windows. Also make sure that you have set up Windows for
Workgroups to use Novell NetWare.
Following are some sample Configuration Files
--------------------------------------------
1. CONFIG.SYS File
FILES=30
BUFFERS=30
LASTDRIVE=Z
DEVICE=C:\windows\HIMEM.SYS
DEVICE=C:\windows\IFSHLP.SYS
STACKS=9,256
2. AUTOEXEC.BAT File
SET TEMP=c:\windows\temp
PATH c:\windows;%PATH%
c:\windows\net start
lsl
smc1660
c:\windows\odihlp.exe
ipxodi
netx
3. PROTOCOL.INI File on Windows for Workgroups 3.11
[network.setup]
version=0x3110
netcard=smc1660,1,SMC1660,4
transport=ms$netbeui,NETBEUI
lana0=smc1660,1,ms$netbeui
[net.cfg]
PATH=C:\WINDOWS\net.cfg
[SMC1660]
[Link Driver SMC1660]
[NETBEUI]
BINDINGS=SMC1660
LANABASE=0
SESSIONS=10
NCBS=12
4. SYSTEM.INI
[boot]
shell=progman.exe
network.drv=wfwnet.drv
.
.
[386Enh]
network=*vnetbios,*vwc,vnetsup.386,vredir.386,vserver.386
netheapsize=20
netmisc=ndis.386,msodisup.386
transport=netbeui.386
InDOSPolling=FALSE
.
.
[Network]
winnet=wfwnet/00025100
multinet=nonet
FileSharing=No
PrintSharing=No
LogonDisconnected=yes
EnableSharing=no
UserName=SMC
Workgroup=WORKGROUP
ComputerName=SMC
Comment=SMC
logonvalidated=no
[network drivers]
devdir=C:\WINDOWS
LoadRMDrivers=No
This commercial computer software and documentation is provided with
RESTRICTED RIGHTS. Use, duplication, or disclosure by the
Government is subject to restrictions set forth in subparagraphs
(c) (1) (ii) of the Rights in Technical Data and Computer Software
clause at DFARS 252.227-7013, or subparagraphs (c) (1) and (2) of the
Commercial Computer Software -- Restricted Rights clause at
FAR 52.227-19, or Alternate III of the Rights in Data -- General
clause at FAR 52.227-14, as applicable. The manufacturer /
subcontractor is Standard Microsystems Corporation, 350 Kennedy Drive,
Hauppauge, NY 11788.
SMC and Standard Microsystems are registered trademarks, and EZ Card 10 is
a trademark of Standard Microsystems Corporation. Other product and
company names are registered trademarks or trademarks of their respective
holders.
===End===
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.