************************************************************************* * SMC Networks, INC * * EZ Connect™ g Wireless Ethernet Bridge * * SMCWEBT-G * * FIRMWARE version V1.09.2 * * 12/01/2007 * ************************************************************************* This document contains three sections: A) Supported part numbers B) The upgrade procedure C) The release history for SMCWEBT-G ========================================================================= Section A: Supported part numbers ========================================================================= This firmware supports products with the following part numbers: 751.8101 751.8102 752.8664 The part number is printed on the label on the bottom of the unit. If your products part number is not listed above do NOT use this firmware. To download the correct firmware check the support section of our website making sure to select the correct part number. ========================================================================= Section B: Upgrade Procedure ========================================================================= 1. Turn on the Wireless Ethernet Bridge and plug it into your network adapter using the Ethernet port. 2. Connect to the Web user interface by typing the Wireless Ethernet Bridge's IP Address (ex: 192.168.2.25)in your browser, then click the login button (if you have not already set a password - otherwise enter in the correct password) 3. Click on the "Advanced" link, then click on "Maintance" and then "Firmware Upgrade" option. The "Firmware Upgrade" screen will appear. 4. Click the "Browse" button and point it to the location of the firmware file. 5. Next click the "Apply" button and follow the prompts. You will notice the lights on the Barricade will react in a certain sequence. Wait patiently while the SMCWEBT-G reboots itself. 6. Your SMCWEBT-G has now been successfully upgraded. Note: It is recommended that once you upgrade your router with this f/w you reset the unit to factory defaults. ========================================================================= Section C: Firmware History ========================================================================= V1.09.2: - Remove Enable/Disable selection in security->802.1X page to let user use easily. - Add “WPA-TKIP only” in SetupWizard step 3. - Add 802.1X in SetupWizard step 3. V1.09.1: - Support 802.1X security function in AP mode. - Fix MAC filter function issue. - Add one item “WPA-TKIP only” to meet customer’s requirement for using wrong PDA/Smart Phone driver in client side to connect. V1.07.2 - Fix crash problem caused by client mode which no AP connected. V1.07.1 - Add a new feature “adjustable sending power” V1.06.2 - Fix “please select an AP” issue at “Setup Wizard” - Fix signal strength percentage in Repeater Mode V1.06.1 - Fix Signal Strength percentage math alogithm - Fix “please select an AP” problem if the user do not click any AP - Add “Default Gateway Address field at “Network Setting” V1.05.1 - Fix Signal Strength Percentages - reverse the % so 100% is strongest signal - Set to Ethernet adapter mode by default - Add ability to manually enter the SSID/Network Information during setup wizard - for those cases in which the customer has hidden their SSID. - Fix IGMP storm problem (AP does not send out any DHCP request packet anymore) V1.04.2 - Change "-dbm" to percentage in client site-survey, status and repeater page v1.04.1 - Fix IGMP traffic issue - Fix long connection issue - Add security settings, site survey function and display information in the setup wizard page V1.03 - Added ANY SSID feature in client mode - WDS: Scan display issue - No info for AP and repeater about channel, assosiated station, link info.. - Password needs to be enterd after every config change - No connection info in Status for wireless settings - Wireless: enabled info in status page unnessesary v1.00 - Shipping versionDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.