Windows 95 or Windows 98 This is an ASCII file called WIN95_98.TXT in the ATI CardAssistant INFO directory. Use a text editor or a word processor with a mono-space font such as Courier to print this file if needed for reference. ************************************************************ ************************************************************ ** ** ** Installing the AT-2700 Drivers on Windows 95 or 98 ** ** ** ************************************************************ ************************************************************ ------------------------------------------------------------ -- Contents -- ------------------------------------------------------------ I. Special Considerations II. Files Needed for Installation III. Installing the AT-2700 with Windows 9x IV. Removing an Existing Driver V. How to See MAC Address I. Special Considerations ========================== Configuration of the AT-2700TX resources is under PCI control. For most applications, no setup other than normal installation of the network software is necessary. To change port settings, to manually view the card's configuration or to run Diagnostics, use the CardAssistant setup program, SETUP27.EXE. The SETUP27 utility only runs on DOS. To enter DOS mode in Windows 9x, reboot and press F8 when the "Starting Windows 9x" message appears. Select the Command prompt only option (#6). To de-install the drivers, use the remove driver option from your Windows 9x Network Control Panel. See "IV. Removing an Existing Driver". II. Files Needed for Installation ================================= The following files are required for installation: \At2700m4.SYS (NDIS4 driver)* \NETATI27.INF (OEM setup file for Windows 95b/95c/98) \NDIS3\At2700m.SYS (NDIS3 driver)* \NDIS3\NETATI27.INF (OEM setup file for Windows 95/95a) \NDIS5\NETATI25M5.SYS (NDIS5 driver) \NDIS5\NETATI27.INF (OEM setup file for Windows 98/NT 5.0) \INFO\WIN95_98.TXT (this file) *NOTE: Use the NDIS4 driver for Windows 95 build 950b and greater, use the NDIS3 driver for Windows 95 build 950a or lower. The NDIS5 driver should be used with Windows 98 and Beta version of Windows 2000 (NT 5.0). You can check the Windows release number in the System Properties dialog box, General tab. III. Installing the AT-2700 with Windows 9x =========================================== 1. With Windows 9x installed as per Microsoft installation instructions, shutdown Windows 9x, power off your computer. 2. Following the instructions in your computer manual for PCI card installation, install your AT-2700 card, and reboot your system. 3. Have the Windows 9x setup CD-ROM disc or floppy diskette(s) available. You will be called on to copy support files for networking. 4. Windows 9x finds the PCI adapter card. The new hardware found message appears, and you are prompted for the driver. 5. Insert the Allied Telesyn CardAssistant diskette in the floppy drive. A dialog box prompts for a source, proposing "A:\". (Read "Files Needed For Installation" eariler in this file for the proper NDIS driver.) Click OK. 6. When prompted by Windows 9x, insert the Windows installation media. 7. Reboot the computer into Windows 9x as prompted. Remove the CardAssistant diskette from the drive and click Yes. Windows 9x will complete the driver installation process. IV. Removing an Existing Driver =============================== 1. From the "My Computer" icon, choose "Control Panel". Then choose "Network". 2. From the "Network" dialog box, select the adapter to remove. Then choose "Remove". 3. Do Not Shutdown or Restart Windows 9x at this time. To install the AT-2700 driver, complete the steps listed in section III. V. How to See MAC Address ========================= To determine a MAC address for a card: 1. Boot the computer into DOS with no drivers loaded. To enter DOS mode in Windows 9x, reboot and press F8 when the "Starting Windows 9x" message appears. Select the Command prompt only option (#6). 2. Insert the CardAssistant diskette in the floppy drive and launch SETUP27: type a:\setup27. 3. The main screen shows a table listing the AT-2700 Fast Ethernet cards installed in the computer. Write down the address(es) listed in the "MAC" column of the table. * Third-party trademarks are the property of their respective owners.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.