TEW-637AP(v1.0R)
****** Disclaimer ******
Our advice is strictly limited to the question asked and is based on the information provided
to us. Trendware does not assume any responsibility or liability for the advice given and shall
not be liable for any direct, indirect, special, incidental or consequential damages in
connection with the use of this information. Always back up your data. For more information,
including technical information updates, please visit our Web site at www.trendnet.com.
************************
<<Warning>> Firmware upgrade failure may permanently damage the unit and causing it not to
function. If the issues in the release note do not address the problem you are experiencing,
please do not upgrade the firmware.
Never upgrade the firmware using a Wireless Computer.
The upgrade procedure may require resetting the Easy N Upgrader to factory default state (all current
settings will be replaced by the default settings), when necessary, please record the unit's
current settings before performing the firmware upgrade.
Please do not load the previously saved Easy N Upgrader"configuration file" to the new firmware.
We apologize for the inconvenience.
****************
<<Upgrade Procedures>>
1. Save the downloaded firmware file on a network PC that can access the TEW-637AP's (Easy N Upgrader) configuration page.
Close all running programs on this PC, disconnect all other PCs from the Router, and power off the DSL/Cable Modem.
2. Unzip the file Firmware, extract the files to the computer's hard
drive and write down the path to the files (i.e. C:\TEW-637AP).
3. From the computer, open Web Browser (i.e. Internet Explorer) and go to the Easy N Upgrader's configuration page (default
address is http://192.168.10.100). Enter the user name and password to login the configuration page
(default no user name and no password) and click "Cancel" at the "Wizard" Window.
4. Click on "Administration" on the left, look for "Status" and check the "Firmware version".
5. From the Upgrade Firmware page, click on "Browse" locate and select the firmware file
(file path from Step 2 above), click on "Open" click on "Upload" and then click on "Ok" at the warning message.
6. You should see a progress bar on the screen.
<<Warning! DO NOT interrupt the upgrade. DO NOT operate the browser. DO NOT disconnect the network cable.
DO NOT power off the Router.>>
7. After the upgrade progress reaches 100%, check the Easy N Upgrader front panel LED lights and make sure "Power" is solid green
and one of the LAN's "Link/Act" is solid green and blinks once in a while. Click "Ok" on the screen.
<<Performing Factory Reset>>
9. To perform the "Factory Reset", with the Easy N Upgrader's power ON, locate the "Reset" button on the rear of the Easy N Upgrader,
use a small pin to press and hold the reset button (front panel "Status" light turns solid Green), wait for 12 seconds
("Status" light blinks Green), and then release the "Reset" button.
10. Wait for 10 more seconds and you should see the front panel's "Power" and one of the LAN's "Link/Act" light up.
<<Note: After the reset, if the "power" and "status" LED flash alternately, please power off the Easy N Upgrader,
wait 10 seconds and then power on the Router.>>
11. From the web browser, go to http:// IP Address of the device, click "Administration", click on "Status" on the left.
12. Power on the DSL/Cable Modem and your wired or wireless Router, wait for the Modem's LED lights are on steadily, use a network cable to connect
the DSL Modem's LAN (Ethernet) port to the Router's WAN port, wait for the Router's WAN LED to light up, use the PC to
go to the Router's "Configuration Page", Reconnect the Ethernet cable to the Easy N Upgrader's LAN port and check the Status LED and make sure
"Power" is solid green and one of the LAN's "Link/Act" is solid green and blinks.
13. Reconnect all the wireless computers to the Easy N Upgrader.
14. The End of the document.
If you need assistance performing the firmware upgrade or if you have any questions, please
contact our Techsupport Team.
Technical Support Numbers and Hours
US and Canada
Hours:
English/Espanol: 24/7
Email: support@trendnet.com
Europe (Germany, France, Italy, Spain, Switzerland, UK)
Toll Free Telephone: +00 800 60 76 76 67
Hours:
English/Espanol: 24/7
Francais/Deutsch: 11am - 8pm, Central Europe Time, Monday - Friday. Except Holidays
Email: support@trendnet.com
Netherlands
Telephone: +020 504 05 35
Hours:
English/Espanol: 24/7
Francais/Deutsch: 11am - 8pm, Central Europe Time, Monday - Friday. Except Holidays
Email: support@trendnet.com
Eesti
Telephone: +372-6593613
Hours: 9am-5pm
Monday - Friday. Except Holidays
Email: support@trendnet.com
Worldwide
Telephone: +(31) (0) 20 504 05 35
Hours:
English/Espanol: 24/7
Francais/Deutsch: 11am - 8pm, Central Europe Time, Monday - Friday. Except Holidays
Email: support@trendnet.com
www.trendnet.com
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.