#
| README file for
|
| ELSA ISDN boards
| Version 2.50
|
| Copyright (c) 1993-99 ELSA AG, Aachen (Germany)
|
| ELSA AG Internet : http://www.elsa.de
| Sonnenweg 11 LocalWeb : +49-(0)241-938800
| D-52070 Aachen
|
| ELSA Inc. Internet : http://www.elsa.com
| 2231 Calle De Luna
| Santa Clara, CA 95054
| USA
|
| ELSA Asia Inc. Internet : http://www.elsa.com
| 7F-11, No. 188, Sec. 5
| Nanking East Road
| Taipei 105
| Taiwan, R. O. C.
|
| ELSA Japan Inc. Internet : http://www.elsa.com
| Mita Suzuki Building 3F
| 5-20-14 Shiba, Minato-ku
| Tokyo 108-0014
| Japan
|
| 04/07/99
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Table of Contents
1. Overview
2. Contents
3. Installation
4. Notes
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1. Overview:
This file contains notes and changes to the
ISDN drivers.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
2. Contents:
The driver disk contains the following files:
README.TXT this file
LIESMICH.TXT german version of the readme.txt file
- - - - - - - - - - - - - - - - - - - - - - - -
2.1 Driver for CAPI 2.0 and DSS1 (EURO-ISDN):
CSSELUNI.VXD CAPI version 2.0 driver for ELSA ISDN boards
D channel protocol : DSS1 (EURO-ISDN)
B channel protocols: HDLC transparent, bit transparent,
X.75, T.70NL, V.120
ISO 8208 (X.25), T.90
modem function (V.34), Fax group 3 function
(V.34 only for PCFpro, QuickStep 3000 and QuickStep 3000-PCI)
(FAX only for PCF, PCFpro, QuickStep 3000 and QuickStep 3000-PCI)
- - - - - - - - - - - - - - - - - - - - - - - -
2.2 Driver for CAPI 2.0 and 1TR6 (national ISDN):
CSS1TUNI.VXD CAPI version 2.0 driver for ELSA ISDN boards
D channel protocol : 1TR6 (national ISDN)
B channel protocols: HDLC transparent, bit transparent,
X.75, T.70NL, V.120
ISO 8208 (X.25), T.90
modem function (V.34), Fax group 3 function
(V.34 only for PCFpro, QuickStep 3000 and QuickStep 3000-PCI)
(FAX only for PCF, PCFpro, QuickStep 3000 and QuickStep 3000-PCI)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3. Installation:
The following illustration shows the mounting bracket of
your ISDN plug and play adapter board :
_____
\ |
| |
|___|
|___|<- ISDN line connector
| |
| o |<- ISDN connection status display (yellow LED)
| o |<- ISDN interface status display (green LED)
| |
| |
| |
|___|
_
________________________________|
| |
| _|
| |_ <- ISDN line connector
| |
| o<- yellow LED
| o<- green LED
| |
| |
| _ __ |
|___| |____________________| |__|
The ISDN plug and play adapter board is full software-
configurable and has NO jumper.
- - - - - - - - - - - - - - - - - - - - - - - -
a.) Install the ISDN-Board in your PC considering
the usual safety rules (look manual).
b.) The driver for your ISDN-Board will be installed
automatically. The Microsoft Accelerator Pack and a
NDIS WAN driver will be installed too.
c.) Restart your computer.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
4. Notes:
The latest information you will always find in the
ELSA LocalWeb or on our homepage.
- - - - - - - - - - - - - - - - - - - - - - - -
V.120 under CAPI 2.0 and CFOS (version newer than 07/15/96):
Enter the following AT-command:
AT B12 S17=1 S76=1
Now, the ISDN adapter board tries to get a V.120 connection
erverytime you dial "ATDn" (n = number)..
If you want to get back to X.75 mode, you have to enter:
AT&F
- - - - - - - - - - - - - - - - - - - - - - - -
Modemconnection under CAPI 2.0 and CFOS:
Enter the following AT-command:
AT B7
Now, the ISDN adapter board tries to get an analog connection
erverytime you dial "ATDn" (n = number)..
For an automatically modemconnection acceptance you must enter
the following AT-commands:
AT &IA S44=1 S0=1
If you want to get back to X.75 mode, you have to enter:
AT&F
- - - - - - - - - - - - - - - - - - - - - - - -
Have fun with your ISDN board.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.