1. RE100TX.zip Driver
2. MSC30.TXT File Contents

MSC30.TXT Driver File Contents (RE100TX.zip)

            ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
            º                                                  º
            º     Microsoft DOS Client Installation Guide      º
            º  Copyright (C) 1998 by PDS. All Rights Reserved. º
            º                                                  º
            ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ GENERAL INFORMATION ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

Mircosoft DOS Client support both NDIS2 and DOS ODI drivers.

ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ INSTALLATION GUIDE  ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
The installation described below is for;

   Compex ReadyLINK Express 10/100Base-TX PCI Fast Ethernet Adapter.

** IMPORTANT:
   ========== 
  If you loading EMM386.EXE v4.49 ensure to exclude memory range D000-DFFF
    e.g. add this statement in Config.sys,
 
       Device=C:\DOS622\EMM386.EXE noems x=d000-dfff



Microsoft DOS Client 3.0
ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ

1. NDIS2 driver Installation

     a) Run SETUP in DISK1.

     b) When asked where the software to install, enter the location,

        e.g.            C:\MSCLIENT

     c) Select "Network adapter not shown an list below ..."

     d) The Install Driver box appears. Insert driver diskette
        into floppy drive and type the path of the NDIS2 driver.
        Enter the driver location,

        e.g.            A:\NDIS2
	
     e) Select "Change Network Configuarion".

     f) Select "Add Protocol" and "Microsoft NetBEUI" to add NETBEUI
        protocol in.

     g) Follow the instruction to complete the installation.

     h) Reboot the PC and RE100TX is now ready to access the network.


2. DOS ODI Driver Installation

     a) Run SETUP in DISK1.

     b) When asked where the software to install, enter the location,

        e.g.            C:\MSCLIENT

     c) Select "ODI/NDIS Support Driver".

     d) Select "Change Network Configuarion".

     e) Select "Add Protocol" and "Microsoft NetBEUI" to add NETBEUI
        protocol in.

     f) Follow the instruction to complete the installation.

     g) Modify PROTOCOL.INI. Change all the lines BINDINGS=ODINSUPMAC
        to BINDINGS=RE100TX as shown by the arrows (<-----) below.
        (there should have three lines needed to be modified).

                PROCOTOL.INI
                ------------
                [network.setup]
                version=0x3110
                netcard=odinsupmac,1,ODINSUPMAC,1
                transport=ms$nwlink,MS$NWLINK
                transport=ms$ndishlp,MS$NDISHLP
                transport=ms$netbeui,MS$NETBEUI
                lana0=odinsupmac,1,ms$nwlink
                lana1=odinsupmac,1,ms$ndishlp
                lana2=odinsupmac,1,ms$netbeui

                [MS$NWLINK]
                FRAME=ETHERNET_802.3
                DriverName=nwlink$
                BINDINGS=RE100       <-----

                [protman]
                DriverName=PROTMAN$
                PRIORITY=MS$NDISHLP

                [ODINSUPMAC]        <-- can be deleted

                [MS$NDISHLP]
                DriverName=ndishlp$
                BINDINGS=RE100TX       <-----
                [MS$NETBEUI]
                DriverName=netbeui$
                SESSIONS=10
                NCBS=12
                BINDINGS=RE100TX       <-----
                LANABASE=1


     h)  Copy from A:\DOSODI directory the following files to 
         C:\NWCLIENT directory;

              LSL.COM, ODINSUP.EXE and RE100TX.COM

     i)  Create or copy the NET.CFG from A:\NDIS2 to C:\NWCLIENT
         Below is a sample of NET.CFG:

                NET.CFG
                -------

                PROTOCOL ODINSUP
                        Bind RE100
                        BUFFERED

                Link Driver RE100TX
                        Frame Ethernet_802.2
                        Frame Ethernet_802.3
                        Frame Ethernet_II
                        Frame Ethernet_SNAP

     l) Modify AUTOEXEC.BAT. Following is a sample for it.

                AUTOEXEC.BAT
                ------------
                c:\NWclient\lsl
                c:\NWclient\RE100TX
                c:\MSClient\net initialize  } These lines are added by
                C:\MSClient\nwlink          } Microsoft DOS Client 3.0
                c:\MSClient\odinsup         } during installation
                c:\MSClient\netbind         }
                c:\MSClient\net start       }

     m) Installation completed.

     n) Reboot the PC and RE100TX is now ready to access the network.