1. 1645BR10.ZIP Driver
2. MAX1535A.INI File Contents

MAX1535A.INI Driver File Contents (1645BR10.ZIP)

; Maxim Smart Battery System Device Definition
; For use with SMBK GUI

;---------------------------------------------------------------------------
; [address] section defines the SMBus device address
; and the display name that appears in the tab.
;
; For a smart charger, the SMBus device address must be 0x12.
;
[address]
0x12=MAX1535A Smart Charger

;---------------------------------------------------------------------------
; [registers] section lists each command
; <hex command byte> = <R | W | RW> , <CommandName> , <bits | unit>
; If the command name units is "bits", the command bits
; are defined in a section [CommandName].
;
[registers]
0x11=Read,ChargerSpecInfo,bits
0x12=Write,ChargerMode,bits
0x13=Read,ChargerStatus,bits
0x14=Write,ChargingCurrent,mA
0x15=Write,ChargingVoltage,mV
0x16=Write,AlarmWarning,bits
0x3F=W,InputCurrent,bits
0xFE=R,ManufacturerID,bits
0xFF=R,DeviceID,bits

;---------------------------------------------------------------------------
; Each command name whose units are defined as "bits"
; gets a section where each bit is named.
; Keys are 16-bit bit masks: four hexadecimal characters with 0x prefix.
; Bits whose name is left blank will display as "reserved".
;
[ChargerSpecInfo]
0x0001=CHARGER_SPEC1
0x0002=CHARGER_SPEC2
0x0004=CHARGER_SPEC4
0x0008=CHARGER_SPEC8
0x0010=SELECTOR_SUPPORT

[ChargerMode]
0x0001=INHIBIT_CHARGE
0x0002=ENABLE_POLLING
0x0004=POR_RESET
0x0008=RESET_TO_ZERO
0x0010=AC_PRESENT_MASK
0x0020=Battery_Present_Mask
0x0040=POWER_FAIL_MASK
0x0100=Calibration_Enable
0x0400=HOT_STOP

[ChargerStatus]
0x0001=CHARGE_INHIBITED
0x0002=MASTER_MODE
0x0004=VOLTAGE_NOTREG
0x0008=CURRENT_NOTREG
0x0010=LEVEL_2
0x0020=LEVEL_3
0x0040=CURRENT_OR
0x0080=VOLTAGE_OR
0x0100=THERMISTOR_OR
0x0200=THERMISTOR_COLD
0x0400=THERMISTOR_HOT
0x0800=THERMISTOR_UR
0x1000=ALARM_INHIBITED
0x2000=POWER_FAIL
0x4000=BATTERY_PRESENT
0x8000=AC_PRESENT

[AlarmWarning]
0x0001=Not Used.
0x0002=Not Used.
0x0004=Not Used.
0x0008=Not Used.
0x0010=Not Used.
0x0020=Not Used.
0x0040=Not Used.
0x0080=Not Used.
0x0100=Not Used.
0x0200=Not Used.
0x0800=Not Used.
0x1000=Over Temperature
0x2000=Other Alarm
0x4000=Terminate Charge
0x8000=Over Charge Alarm

[DeviceID]
0x0001=DeviceID_bit0
0x0002=DeviceID_bit1
0x0004=DeviceID_bit2
0x0008=DeviceID_bit3
0x0010=DeviceID_bit4
0x0020=DeviceID_bit5
0x0040=DeviceID_bit6
0x0080=DeviceID_bit7
0x0100=DeviceID_bit8
0x0200=DeviceID_bit9
0x0400=DeviceID_bit10
0x0800=DeviceID_bit11
0x1000=DeviceID_bit12
0x2000=DeviceID_bit13
0x4000=DeviceID_bit14
0x8000=DeviceID_bit15

[ManufacturerID]
0x0001=ManufacturerID_bit0
0x0002=ManufacturerID_bit1
0x0004=ManufacturerID_bit2
0x0008=ManufacturerID_bit3
0x0010=ManufacturerID_bit4
0x0020=ManufacturerID_bit5
0x0040=ManufacturerID_bit6
0x0080=ManufacturerID_bit7
0x0100=ManufacturerID_bit8
0x0200=ManufacturerID_bit9
0x0400=ManufacturerID_bit10
0x0800=ManufacturerID_bit11
0x1000=ManufacturerID_bit12
0x2000=ManufacturerID_bit13
0x4000=ManufacturerID_bit14
0x8000=ManufacturerID_bit15

[InputCurrent]
0x0001=Not Used.
0x0002=Not Used.
0x0004=Not Used.
0x0008=Not Used.
0x0010=Not Used.
0x0020=Not Used.
0x0040=Not Used.
0x0080=Adds 256mA
0x0100=Adds 512mA
0x0200=Adds 1024mA
0x0400=Adds 2048mA
0x0800=Adds 4096mA
0x1000=Adds 8192mA
0x2000=Not Used.
0x4000=Not Used.
0x8000=Not Used.