Thank you for purchasing an Epson printer. This document contains notes regarding your new printer. -------------------------------------------------------------------------------------------------------------------------- README file for EPSON EPL Series Printer Driver for Microsoft(R) Windows(R) 3.1, Windows(R) 95, Windows(R) 98 and Windows NT(R) 3.51/4.0 -------------------------------------------------------------------------------------------------------------------------- [Contents] 1. Introduction 2. Important legal information 3. Install notes -------------------------------------------------------------------------------------------------------------------------- 1. Introduction This document contains information that you should be aware of when printing with Windows. 2. Important legal information Software called the EPSON EPL Series Printer Driver (the "Software") is provided "AS IS." NO IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE ARE GIVEN. The Software may be copied and distributed without charge only to users of EPSON brand printers. All files on the disk must be copied without modification, including all proprietary marks and notices. All components of the Software must be distributed together. The Software may not be distributed for profit. Copyright (c) 1999 SEIKO EPSON CORPORATION 3. Install notes Run setup.exe in disk1 on each Operating System. make sure that, *all other applications are closed, and all print jobs are finished before installing the printer driver. *when asked by the install program whether you wish to "Keep existing driver" OR "Replace existing driver", always select the replace option. 4. Notes regarding printing (1) 1200 dpi Some applications don't support printing with 1200 dpi; therefore, if you do not get good results printing with "True 1200 dpi" selected (2) Printing with Raster selected as the Graphic Mode If you do not get good results printing from some applications with "Raster" selected as the Graphic Mode setting in the Extended Settings dialog box, try selecting "Printer" or "Host" and then printing again. as the Print Quality setting on the Basic tab, try selecting "Class 1200 dpi" or "600 dpi" and then printing again. (3) Setting Up Drivers From Within Applications Print setup is not available from within some applications. Setting print conditions for the driver from these applications will have no effect on printing. When using applications that do not support print setup, print only after setting the driver print conditions from the Control Panel. (4) Zoom Options Printing The edges of the original may not be printed in the Zoom Options modes. Make sure that sufficient space is available for the left, right, top and bottom margins when printing in these modes. (5) Collate When using the collate function, follow the steps below. 1) Install 64 MB or more memory in the printer and set the correct memory size in Installed Memory on the driver [Option Setting] dialog box. 2) Turn Collate on in the [Basic Settings] tab in the printer driver. 3) In the [Basic Settings] tab, select an output tray other than Sorter or Multiple Sorter. 4) Collate function, Sorter Mode, and Multiple Sorter Mode If you have any problems printing in any of the functions or modes above, turn the Collate option off in applications that can select collate from the print dialog box. (6) If you cannot get good printed results from some applications in Windows NT 4.0, follow the steps below. 1) Open Printer Properties from Control Panel. 2) Click "Printer Processor..." button in the [General] tab. 3) Select "Always spool RAW datatype" as on. 4) Print the data again. (7) Euro Symbol Printing The printer driver supports Euro Symbol with the following internal printer fonts; Courier SWC Dutch 801 SWM Swiss 721 SWM Dutch 801 SWC Zapf Humanist 601 SWC Ribbon 131 SWC Clarendon Condensed SWC Swiss 742 SWC Swiss 742 Condensed SWC Incised 901 SWC Original Garamond SWC Audrey Two SWC Flareserif 821 SWC Flareserif 821 Extra Bold SWC Letter Gothic SWC If you have problems print in Euro Symbols, check the Font Substitution Table of the printer driver. You can print Euro Symbols without using internal printer fonts if you have screen fonts which support the Euro Symbol in your system. To do that, change "TrueType fonts with substitution" to "Print TrueType fonts as bitmap" in the [Extended Settings] dialog box on the [Optional Settings] tab of the printer driver before you print. -------------------------------------------------------------------------------------------------------------------------- Microsoft is registered trademark and Windows is registered trademark of Microsoft Corporation in the United States and other countries. Product and Company names listed in this document are all registered trademarks of their respective Companies. --------------------------------------------------------------------- The following contains the latest information about your EPSON Status Monitor 3. 07/13/99 --------------------------------------------------------------------- 1. General troubleshooting solutions 1-1. Notes for using EPSON Status Monitor 2 and EPSON Status Monitor 3 together EPSON Status Monitor3 turns on monitoring of the following types of connections, even if these settings are disabled by EPSON Status Monitor 2. * local printers * LPR printers * NetWare printers * Windows shared printers These settings should work most in cases. If you install EPSON Status Monitor 2 and change the monitoring settings, it will also change EPSON Status Monitor 3's settings. This can cause problems printing and monitoring. (Note) *If a particular communication protocol is not installed, the monitor settings will not be enabled. *To setup EPSON Status Monitor 3, please re-install your printer driver. 1-2. If a Windows shared printer cannot be monitored, check that the following settings have been made: * Make sure that the printer driver is installed on the computer that is hosting the Windows shared printer, that it is set to be shared, and "Allow monitoring of shared printers" is selected in the "Monitoring Preferences" of the printer driver. * (Windows98/95 only) Open the "Network" icon in the control panel on the computer that is sharing the printer, and check that File and Printer Sharing for Microsoft Networks component is installed. * (Windows98/95 only) As above, check that IPX/SPX-compatible Protocol is NOT installed on either the client or server computers. 2. Solutions for Windows NT environment 2-1. When un-installing EPSON Status Monitor 3 from a multi-user Windows NT environment, turn off the Shortcut Icon on all clients before un-installing. You can turn off the Shortcut Icon in Monitoring Preferences. 2-2. When using a Windows NT 4.0 shared printer in a non-updated Windows NT environment, if you check "Allow monitoring of shared printer", and then start EPSON Status Monitor 3, the Application Error Notice Window appears and you cannot monitor NetWare shared printers. To avoid this problem, make sure you have installed Windows NT 4.0 Service Pack 2 or later. 2-3. When using a Windows NT 4.0 shared printer, if you check "Allow monitoring of shared printer", and then start EPSON Status Monitor 3, you cannot monitor a NetWare shared printer . To avoid this problem open "Services" from the control panel, stop the EPSON Printer Status Agent service, and start EPSON Status Monitor 3. After EPSON Status Monitor 3 has started, restart the printer status service. You must do this each time you log into Windows NT 4.0. 2-4. In Windows NT, when connecting a shared printer on the server, be sure to do the following to all client PCs: *Clear the "Allow monitoring of shared printer" checkbox in the driver's Monitoring Preferences window. *Stop EPSON Net WebManager. You need Administrator's privileges to change these settings. See the EPSON Net WebManager User's Guide for more details. 3. Solutions for network printers 3-1. To monitor a NetWare printer, connect only one print server to each queue. See your User's Guide for directions. 3-2. You cannot monitor a NetWare queue printer beyond the IPX router because the setting for IPX hops is 0. 3-3. When monitoring NDS printers, the client supplied by Novell must be used: When using Windows NT: Novell IntranetWare Client for Windows NT When using Windows 95: Novell IntranetWare Client 32 for Windows 95 3-4. To monitor an LPR printer in a Windows NT environment, set only "Name or address of server providing lpd:" in the "Add LPR compatible printer" dialog box for the LPR Port. 3-5. Monitoring NDPS printers This product supports Netware printers configured by a queue-based printing system such as Bindery or NDS server. You cannot monitor NDPS (Novell Distributed Printing Services) printers. --------------------------------------------------------------------- General notice: Product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks. (C)SEIKO EPSON Corp.1999 ENDDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.