Driver Installation Guide for Windows NT 4.0
===================================================
Introduction
============
This document describes the procedure to install NDIS4 driver on MS
Windows NT 4.0 for Addtron AWP-100 PC CARD Adapter.
Location of Driver: \AWP-100\WINNT40\CW10.SYS
\AWP-100\WINNT40\OEMSETUP.INF
* CW10.SYS is a NDIS4 driver for Windows NT 4.0 Serve/Workstation
System . Although the " Addtron AWP-100 PC CARD Adapter" has
supported "Hot swap" and "Plug and Play" capability, but Windows
NT platform didn't support it. So,remind to insert or remove this
PC Card must at POWER OFF state.
* OEMSETUP.INF is a Network Setup Information File for NT Platforms.
For Windows NT 4.0 user, you have to locate this information file
explicitly when the Windows device wizard is asking you where to
find the information file for the device driver to be loaded.
Installation Procedure
======================
1. Make sure your computer power is off.
2. Insert the Addtron AWP-100 PC Card into your computer.
3. Startup your Windows NT system and logon as Administrator.
4. To install driver, click "start" , select the " Settings " item
and click the "Control Panel" item to open.
5. In the Control Panel window, click on the "Network" icon.
6. In the Network Configuration dialog box, choose the "Adapters"
menu.
7. Click on the "Add..." button.
8. When the Select Network adapter Type dialog box appears, select
"Have Disk..." button.
9. When "Install Disk" dialog box appear,insert the driver CD into
CD-ROM and specify the path of the driver in the CD-ROM ( i.e.
D:\AWP-100\WINNT40 ) . then click on "OK" button.
10. You will see "Addtron AWP-100 PC CARD Adapter" list in the
dialog box and please click on "OK" button again.
11. The Windows NT 4.0 begins to copy driver from diskette and some
system files from Windows NT CD-ROM or diskette.
13. You will see " Addtron AWP-100 PC CARD Adapter" list in the
Network Configuration dialog box and to be configured.
14. Once you have finished the installation procedures, please click
on the "Close" button . The Windows NT will prompt you of the
TCP/IP Properties . Click the "OK" button , when you have config
completed .
15. Restart your system and you will acquire network service.
Troubleshooting
===============
1. If you have finished the installation of the driver in WinNT 4.0
but fail to work with the network.
Solution:
a. Click on "Control Panel" icon and choose"Devices" icon.
b. Search for "Pcmcia" device item. You will see that the
PCMCIA is disabled.
c. Switch the " Pcmcia " device item from " Disable " into
"Boot" by selecting "Boot" item to be active.
d. Reboot the system.
2. After the installation, if you just find a computer in neighbor
but ping test time out.
Solution:
a. Check whether if the adapter bind TCP/IP and Enable TCP/IP
protocol.
b. Check system resources , the IRQ and I/O Base of PC Card
whether if are occupied by other device.
3. If your network still not work. Install " Wireless LAN Configu~
ration Utility " and check NIC configuration.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.