1. unex_pcmcia.zip Driver
2. SETUP.TXT File Contents

SETUP.TXT Driver File Contents (unex_pcmcia.zip)

*****************************************************************************
*                                                                           *
*                  32-BIT IO MODE PCI ETHERNET ADAPTER                      *
*                                                                           *
*                         SETUP.EXE USER GUIDE                              *
*                                                                           *
*****************************************************************************

The SETUP.EXE program is used to set the adapter's configuration
and diagnose the adapter's hardware.

Note
====

**************************************
*   Conflict with Microsoft EMM386   *
**************************************

The PCI adapters can only function with the EMM386.exe memory manager
program version 4.49 or later.  You can verify its version number by
entering EMM386 at the DOS Prompt.

Do not specify the "HIGHSCAN" option with the EMM386.exe statement in
your config.sys file or your system will hang.

If you run MEMMAKER and select Custom Setup, do not specify
"Aggressively scan upper memory", or it will automatically insert the
HIGHSCAN flag into the EMM386 command line.  This parameter cannot be
removed once it's installed,  doing so will cause the extended memory
manager to malfunction.



Starting the Program
====================

A. At the DOS prompt, go to the directory where th SETUP program is located.
Then type in:

   A:\>SETUP      <Enter>

B. Identify your adapter. Use the up/down arrow keys to select
   the appropriate adapter card.

Note
----
If there is more than one adapter installed in the host PC,
the SETUP program will prompt you to specify which card you want to
configure.  The PCI BIOS will automatically assigns the I/O base or IRQ
address for the adapter.

C. The SETUP provides the following functions to configure the adapter
   and diagnose the adapter's hardware.


                    View Current Configuration
                    Set Up New Configuration
                    Run Diagnostics
                    Exit SETUP



View Current Configuration
==========================

1. Use the up/down arrow keys to select the "VIEW CURRENT CONFIGURATION"
   option and press <Enter> to view the current adapter's configuration
   settings.

2. This function displays the adapter's configuration such as:

   *  Ethernet Address
   *  Medium Type (AUTO DETECT, AUI)
   *  Full-Duplex
   *  I/O Base Address
   *  Interrupt
   *  Boot ROM Size

3. Press the <Space> bar or <ESC> key to return to the main menu.



Set Up New Configuration
========================

1. Use the up/down arrow keys to select "SET UP NEW CONFIGURATION".  Press
   <Enter> to display the follwoing configuration option:

   *  Medium Type (AUTO DETECT, AUI)
   *  Full-Duplex
   *  Boot ROM Size
   *  Flow Control

2. If there is any change value for any item,  Press ESC key and
   ENTER key to update value of item.

3. Use the <ESC> key to exit the setup configuration screen and confirm
   the changes made.


Run EEPROM Test
===============

1. Use the up/down arrow keys to select "RUN EEPROM TEST".
   Press <Enter> to test the adapter's On-Board EEPROM.

2. The program will run the READ tests for each register in the EEPROM.


Run Diagnostics On Board
========================

1. Choose the "RUN DIAGNOSTICS ON BOARD" option to test the adapter's
   components and its installation.  Press <Enter> to perform
   the following tests.

           *     Configuration test
           *     I/O Registers test
           *     Internal loopback test
           *     External loopback test
           *     RAM test

2. These tests monitor the adapter and corresponding cabling system;
   however, not testing the network condition.

   The screen will display the PASSED or FAILED count for each test.
   If any test fails, press the <Space> bar to display the reason of
   failure and possible solutions.

3. The adapter tests check the following items ---

   *   Configuration Test checks the initial status of the
       Ethernet Controller
   *   I/O Registers Test checks I/O accessibility
   *   Internal Loopback Test checks adapter's controller
   *   External Loopback Test checks the network link
   *   RAM Test checks the condition of on-board RAM



Run Diagnostics On Network
==========================

1. Using the up/down arrow keys to choose the "RUN DIAGNOSTICS ON NETWORK"
   option. Press <Enter> to perform this option.

2. The program will thoroughly verify your adapter's ability for the device
   communication on the network.

3. Set up at least one computer as a Responder and one as an Initiator.

4. The Responder displays the status of communications with
   each Initiator on the network.

5. The Initiator displays the current Responder and the status
   of corresponding communications.

6. The Responder communicates with one Initiator at a time.


Exit SETUP
==========

Choose the "EXIT SETUP" option to exit the [SETUP] program and return to DOS.



TRADEMARKS
==========
All trademarks or brand names mentioned are trademarks or registered
trademarks of their respective companies.