readme.txt Driver File Contents (sae3v560.exe)

README.TXT                                                    2008-06-27 CDC
ACPI Flash BIOS version 5.60 for Satellite A205 (PSAE3U) - Windows XP Only
-----------------------------------------------------------------------------

This BIOS is applicable to the following models:

Satellite A205-S5825
Satellite A205-S5831
Satellite A205-S5833
Satellite A205-S5835
Satellite A205-S5841
Satellite A205-S5843
Satellite A205-S5847
Satellite A205-S5851
Satellite A205-S5852
Satellite A205-S5853
Satellite A205-S5855
Satellite A205-S5859
Satellite A205-S5861
Satellite A205-S5863
Satellite A205-S5864
Satellite A205-S5867
Satellite A205-S5871
Satellite A205-S5872
Satellite A205-S5878
Satellite A205-S5879
Satellite A205-S5880


For purposes of this document, the term "Satellite A205"
is used to generically refer to all of the models listed above.


-------------------------------------------
This archive contains the following files:
-------------------------------------------

README.TXT      Installation/usage instructions in ASCII text format
2084d560.exe    Self-extracting diskette image of BIOS install diskette
setup.exe       Windows-installed BIOS package
LAUNCHER.EXE    BIOS Installation Launcher application. The Launcher
                displays a Windows dialog from which you can choose a BIOS
                installation option appropriate for your system and Windows
                version.  There are various other files in support of the
                BIOS Installation Launcher which are not listed here.
sae3v560.iso    ISO Image of bootable BIOS Installation CD-ROM
                See instructions below regarding the use of this image


********************** CAUTION! *********************************************
*****************************************************************************

During the upgrading of your computers BIOS, if the computer loses power or
fails to complete the process of upgrading the BIOS, the existing BIOS in
the computer may become damaged.  Toshiba HIGHLY recommends that the computer
is powered via the AC adapter during the entire BIOS update process.

In the event of a power loss during the BIOS update process, the BIOS Key
Installation Method, described below, can sometimes be used to recover from
the failure.  If it does not, you'll need to have your computer serviced by a
Toshiba Authorized Service Provider (ASP).  You can select an ASP in your
area at http://pcrepair.toshiba.com

Toshiba also recommends that you disconnect all peripheral devices from your
computer before you perform the BIOS update.  Peripheral devices include, but
are not limited to, docking devices (Desk Stations, port replicators), PCMCIA
and CardBus cards, USB and IEEE 1394 devices, printers, scanners, digital
cameras, etc.

On some models, it is not unusual to see a CMOS checksum error when you first
reboot the computer after installing the new BIOS.  If you see this message
on your screen, press F1 as instructed.  This displays the "TSETUP" screen.
Press <End> to save the CMOS data.  You won't see the CMOS checksum error
again.

*****************************************************************************


-------------------------------
BIOS INSTALLATION INSTRUCTIONS
-------------------------------

There are three options for installing this BIOS release:

1) From the bootable BIOS installation diskette.  This is the recommeded
   procedure whenever a diskette drive (internal, USB, or PCMCIA) is
   available on the target system.

2) From within Windows NT-based operating systems (XP, 2000, NT 4.0) using
   the Windows-based BIOS installer.

3) From the bootable BIOS installation CD-ROM


---------------------------------------------------
1) BOOT DISKETTE INSTALLATION METHOD (Recommended)
---------------------------------------------------

The BIOS installation launcher offers the option to create a bootable BIOS
installation diskette.  Simply select 'Diskette Installation' from the
Launcher menu and click 'Ok'.  You'll need to have a diskette drive
(internal, USB, or PCMCIA) installed, and a formatted 1.44MB diskette
available.

Once the BIOS installation diskette has been created, install the BIOS
using the following steps:

      o Connect the computer to AC power using the AC adapter.
      o Close all open programs
      o Insert the BIOS installation diskette into your diskette drive (A:)
      o Shut down the operating system.  With Windows, you may choose to
        Restart rather than shutting down.
      o If necessary, restart the computer by pressing Ctrl-Alt-Del or
        turning the computer OFF then on again

The computer will boot MS-DOS from the BIOS installation diskette, and
initiate the Flash BIOS installation routine.  Please note that on systems
where only a USB-connected diskette drive is supported, you can force the
computer to boot from the USB-connected diskette by holding down the "U" key,
when powering-on the system.

When the Flash BIOS update is complete, a message like the one below will be
displayed:


        Please push the RESET SW (or turn AC power OFF/ON) to restart!

                             ROM Write Successful!
                               Utility Finished!



Eject the diskette from drive A: and turn the computer OFF then ON, or press
the reset switch to restart your computer.


=== ADDITIONAL INFORMATION REGARDING THIS INSTALLATION METHOD ===

If you are unable to use the Windows self-extractor, the self-extracting
ZIP archive can be extracted using PKUnZip, Info-Zip, or an equivalent UnZIP
utility.  The Zip archive was created with Info-Zip (http://www.info-zip.org)
and the self-extractor (SFX) is WinZip (http://www.winzip.com)

The WinImage self-extracting diskette image, 2084d560.exe, is a 32-bit
Windows application that requires Windows 9x, Me, NT, 2000, or XP.
Information about WinImage is available at http://www.winimage.com.

For Linux or other operating systems, you can use the boot CD-ROM method or
you can create the BIOS installation diskette on a Windows-based computer,
and boot the Toshiba notebook using the BIOS installation diskette.


-----------------------------------------------
2) INSTALLATION FROM WITHIN WINDOWS NT/2000/XP
-----------------------------------------------

This release offers the option to install the BIOS directly from within
Windows NT-based operating systems.  To do so, simply select the 'Windows
Installation' option from the Launcher menu, and click 'Ok'.

IMPORTANT INFORMATION REGARDING THIS INSTALLATION METHOD
Please close all programs before executing the Windows NT-based installer.

Due to the somewhat increased risk of errors updating the BIOS from within
Windows (as compared to using the boot diskette method), it is HIGHLY
recommended that the computer be connected to AC power via the AC adapter,
and that the power-save mode is set to 'Full Power' or the equivalent while
installing the BIOS.

The Windows NT-based BIOS installer, setup.exe, will install the flash
BIOS when run under Windows NT 4.0, Windows 2000, or Windows XP.

The Windows NT-based installer requires Administrator priveleges on the
target system, and, for Windows 2000/XP, requires that the Toshiba Value-
added Logic Device driver (TVALD, or ACPI common modules) be installed and
working.

Windows 95, 98, and Me are not supported.  If executed under Windows 9x/Me,
the Launcher will not offer the option to install from within Windows.

---------------------------------------------------
3) BOOT CD-ROM INSTALLATION METHOD
---------------------------------------------------
If your Toshiba PC is equipped with a bootable CD-ROM device (CD-ROM,
DVD-ROM, DVD-RW, DVD-Multi, etc.), and you have access to a CD writer
(burner, either installed in your Toshiba PC or in another PC), you can create
a bootable BIOS installation CD-ROM using the ISO CD image, sae3v560.iso,
provided in this distribution.

If you have CD burning software on your computer, chances are good it has set
itself up as the default handler for ISO CD-ROM images.  If this is the case,
the option to create the bootable CD-ROM from the BIOS Launcher, will launch
your CD burning software, ready to burn the ISO image to CD.  If your software
hasn't set itself up as the default handler for ISO images, we'll recognize
that fact, and let you know.

Once you create the bootable CD-ROM, simply boot your computer from the
resulting CD.  To boot from CD, you can either hold down the "C" key while
you turn your computer on, or you can use HWSetup to change the boot priority
so the CD drive boots before the HDD.

Note, if your CD burner supports it, you can use a rewritable CD (CD-RW) disc
to create the bootable BIOS installation CD-ROM.  Be sure to erase the
rewritable disc (if it has data on it) before you proceed.  Once you are
finished updating your system's DMI values, you can erase and re-use the
rewritable disc.

IMPORTANT NOTE: Creating the bootable BIOS installation CD requires a specific
                set of steps that is unique to each CD authoring application.
                You cannot simply copy the ISO image to a blank CD and expect
                to be able to boot from it.

-----------------------------------------------------------------------------
Here are brief instructions for creating a CD from the ISO image using widely
available software.
-----------------------------------------------------------------------------

* Roxio Easy CD Creator:
  Easy CD Creator 5, bundled with some Toshiba PCs, allows you to initiate
  the ISO image to CD burning process by simply double-clicking the .ISO file
  in Windows Explorer. Simply browse to the folder into which you downloaded
  the ISO image file and double-click to launch Easy CD Creator. Then put a
  blank CD-R media in your drive and click on the 'Record' button to begin
  creating the CD.

  Information about Easy CD Creator is available at http://www.roxio.com


* Nero:
  Nero 6 is available for download as a fully-functional demo. Nero can be
  used to create a CD from your ISO image using either of the two following
  techniques:

	o In Nero Burning ROM go to menu option 'Recorder --> Burn Image' and
	  navigate to the drive/folder containing the ISO image you wish to
	  burn to CD.

	o In Nero Express select the option for 'Disc Image or Saved Project'
	  to select the ISO image file and burn to CD.

More information about Nero 6 and a downloadable demo is available at
http://www.nero.com


Drag 'n Drop CD:
The Drag 'n Drop CD application bundled with some Toshiba PC models does not
support creating a CD from an ISO image.  You'll need to use a different CD
burning application. If Roxio Easy CD Creator (see above) is not on your PC,
one application that can be used with Windows XP is Alex Feinman's free "ISO
Recorder Power Toy". This software allows you to right-click on .iso files and
use Windows XP's built-in CD writing wizard to create CDs from ISO image files.

Information about the ISO Recorder Power Toy is available at
http://isorecorder.alexfeinman.com/isorecorder.htm


Note: Information about non-bundled software is provided "for your
      information".  Toshiba neither recommends nor supports software that
      is not bundled with our computers or purchased from toshibadirect.com.


--------------------------------------
CHANGE HISTORY for Satellite A205
--------------------------------------

Version 5.60  2008-05-31
   o Implemented a workaround for an Intel ICH8M SATA Init LPM issue.
   o Added an enable/disable BOOT devices capability to support TsuRuWIN.EXE.
   o Added a logo.
   o A modification was made for the Japanese keyboard.
   o A LidOut Scancode was added.

Version 5.40  2008-03-03
   o Disabled the Atheros XB63 WLAN ASPM L0s function.
   o Updated Penryn CPU Micro code.
   o Updated Merom CPU Micro code.



 **end**
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web4, load: 0.40