#9/6/03 - preliminary, fixed analog config---bad schematics; no UJCA. Schematic review is still necessary!!! [Models] ;all MODEL files (except perhaps STAC97.ini) should have a self-reference here. ;self-reference: #MANUAL EDIT: Change ID number to proper value PCI\VEN_8086&DEV_24D5&subsys_3005107B= this [DelRegKeys] # Specify the registry keys to be deleted during Uninstall HKCU\Software\Sigmatel\Settings=Yes ; Delete the current user's settings subkey HKCU\Software\Sigmatel\JackSense=Yes ; Delete the current user's jacksense subkey HKCU\Software\Sigmatel\JackSense2=Yes ; Delete new user key HKLM\Software\Sigmatel\JackSense2=Yes ; both of them HKR\Settings=Yes ; Delete the driver's settings subkey HKR\JackSense=Yes ; Delete the driver's jacksense subkey # The following 2 keys cause the volume settings to be 'forgotten' during Uninstall HKCU\Software\Microsoft\Windows\CurrentVersion\Applets\Volume Control\SigmaTel Audio=Yes HKU\Software\Microsoft\Windows\CurrentVersion\Applets\Volume Control\SigmaTel Audio=Yes [Apps] # Specify the application software to install TinyUJ2 = No SSWiz = NO StacSysTray = NO StacIt = NO PassThru = NO [HKR\Settings] EmulateAllMasters = hex: 1 DigitalMasterControlsAnalog = hex: 0 DockedIfJustCodecReady = hex: 0 EnableLinearVolumes = hex: 0 MakeCodecsPlayInParallel = hex: 0 DisableCDIn = hex: 0 MuteInactiveDac = hex: 0 SPDIFInMute = hex: 0 SPDIFInSharesJackWithAnalogIn = hex: 0 DisableHeadphone = hex: 1 DisableLnlvl = hex: 1 DisableWaveIn2 = hex: 1 DisablePCBeep = hex: 0 DisablePhone = hex: 0 SPDIFInSupportVariant = hex: 0 DisableMonoOut = hex: 1 DisableAux = hex: 1 DisableVideo = hex: 1 Disable3DControl = hex: 1 DisableMonoVirtual = hex: 1 DisableMICSelect = hex: 0 DisableLineInFromPlayback = hex: 1 DisableMicFromPlayback = hex: 1 DisablePeakmeters = hex: 1 EnableSPDIFIn = hex: 0 MICBoost = hex: 1 MasterControlsAux = hex: 0 MasterControlsMono = hex: 0 RecMuxMuteAtFloor = hex: 0 MICSelect = hex: 0 3DDepthEnable = hex: 0 PCBeepMute = hex: 1 PhoneMute = hex: 1 CDMute = hex: 1 VideoMute = hex: 1 AuxMute = hex: 1 EnableExtAmpControl = hex: 0 EnableNonPCMOnWin2K = hex: 1 EnableStereoMic = hex: 0 MultichannelEnabledByUser = hex: 0 EnableNewVolumeControls = hex: 1 ##Hand Edits for New Keys Follow MultiChannelDisable = hex: 1 EnableAltMicSupport = hex: 1 Mic1Selector = hex: 04 Mic2Selector = hex: 0 # These settings control the values loaded into the AC97 registers by the driver. # This allows setting the configuration prior to any applets running. ####################################################### # the following settings setup 2 channel plus Mic and # Line-In on the system, plus 6 channel on the dock. # Be careful with R6E. Only 1 codec can be inputting # at a time. Setting the off codec to slots 6-9 will # effectively disable it. ####################################################### 0_76588384_R3E = hex: 01, 00 ; R3E = 0x0001 0_76588384_R4C = hex: 0D, 00 ; R4C = 0x000D 0_76588384_R4E = hex: FD, FF ; R4E = 0xFFFD 0_76588384_R54 = hex: 0A, 00 ; R54 = 0x000A 0_76588384_R64 = hex: 58, C2 ; R64 = 0xC258 0_76588384_R66 = hex: 00, 04 ; R66 = 0x0400 0_76588384_R68 = hex: 00, 20 ; R68 = 0x2000 0_76588384_R6E = hex: 00, 10 ; R6E = 0x1000 0_76588384_R74 = hex: 00, 08 ; R74 = 0x0800 BiosInterfaceAddress = dword: 0x000F0000 ; address in physical memory BiosInterfaceAddressEnd = dword: 0x000FFFFF ; address in physical memory ############################################################ #The following settings must be hand-edited in the INI file ############################################################ # This SPDIFSharedPinMuxBIts value is required when we have SPDIF OUT on the same jack as any analog inputs/outputs (LINE IN, REAR etc.). # When user enables SPDIF OUT driver uses this mask to check if this jack is configured as analog input or output # and if it is it will remember that SPDIF OUT is on but actually won't turn it on until this jack is reconfigured # as digital input/output. Digital input/output means that this jack is turned off in reg 64 and is not selected as # input source in reg 66. # Last three bits are shared pin mux bits from register 66 # In all higher bits the 1 should be provided at position of the bit that powers shared pin in reg. 64. # Below we have bit 15 set, which powers pin43/44 and 5 is mux value of pin 43/44 in reg66. SPDIFSharedPinMuxBits =DWORD:0x0042 ; pin 23/24 is shared with SPDIF on PA1 PCMVolumeFixedLevel = hex: 08, 08 ; only meaningful in analog or DigitalMasterControlsAnalog mode WaveInMux = hex: 00, 00, 00, 00 ; normally Mic # Volume units are represented in fixed point hexadecimal, # in the same units that the OS passes to the driver. # [ADC Gain] [Output volume] [Input Volume] # [Reg 0x1C] [Regs 2,4,6,36,38] [Regs A,C,E,10,12,14,16,18] # +22.5 dB 16.8000h = 0x00168000 max slider # +12 dB = 0C.0000h = 0x000C0000 1/4 slider max slider # +06 dB = 06.0000h = 0x00060000 1/2 slider # 0 dB = 00.0000h = 0x00000000 min slider max slider 1/4 slider # -0.5 dB = FFFF.8000h = 0xFFFF8000 # -1 dB = FFFF.0000h = 0xFFFF0000 # -6 dB = FFFA.0000h = 0xFFFF0000 1/2 slider 1/8 slider # -12 dB = FFFA.0000h = 0xFFFF0000 1/4 slider 1/16 slider # -18 dB = FFFA.0000h = 0xFFFF0000 1/8 slider #-35.5 dB = FFDD.8000h = 0xFFDD8000 min slider # -46 dB = FFD2.0000h = 0xFFD20000 min slider MICAtRecMuxVolume = hex: 63, D0, 13, 00 ; (0-168000) MICVolume = hex: 90, 56, 08, 00 ; (ffdd8000-c0000), (5 bit control). CDVolume = hex: 89, F5, FF, FF ; (ffdd8000-c0000), (5 bit controls). # Other settingsDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.