READ ME for
Cornerstone Monitor
Inf file for:
Windows 95
Windows 98
Windows Me
Windows 2000
Windows XP
Inf Installation Instructions
Cornerstone Customer Support
Inf Installation Instructions
=============================
Installation
------------
First, if you are using Windows 95, determine which version
of Windows 95 you are using. To do this, place your mouse
cursor over the "My Computer" icon and perform a right click.
From the list, select properties. Look at the "General" tab.
You should see -
System:
Microsoft Windows 95
4.00.95xx
Look at the line that starts with 4.00. If your system reports
either 4.00.950 or 4.00.950a then proceed to section 1.
If your system reports 4.00.950b proceed to section 2.
For Windows 98 proceed to section 3
For Windows Me proceed to section 4
For Windows 2000 proceed to section 5
For Windows XP proceed to section 6
SECTION 1 -- Installing In Windows 95, (Classic)
=================================================
NOTE: Be sure to exit all applications before starting
the setup.
1. Begin by going to your Display Properties Page. You can do
this by right clicking on your desktop & selecting Properties
or by going to the Control Panel & Double Clicking on the
Display icon.
2. Go to the Settings tab.
3. Click the Change Display Type button.
4. In the Change Display Type Window, click the Change
button to the right of the Monitor Type Field.
5. In the Select Device Window, click the Have Disk
button.
6. Supply the location of inf file & click OK.
The default location is A:\. If you have copied the
file to a different drive, type the location in the
"Copy manufacturers files from" field.
7. From the list choose the appropriate Cornerstone
Monitor and click OK.
8. Once your selection appears in the Change Display
Type Window, click on close.
9. Click Apply and then the OK button to save the changes.
10. Adjust your monitor as needed. Consult your Cornerstone
Display Manual for further information on adjusting
screen size & position.
SECTION 2 -- Installing In Windows 95, (OSR2)
=============================================
NOTE: Be sure to exit all applications before starting
the setup.
1. Begin by going to your Display Properties Page. You can do
this by right clicking on your desktop & selecting Properties
or by going to the Control Panel & Double Clicking on the
Display icon.
2. Go to the Settings tab.
3. Click the Advanced Properties button.
4. Click on the Monitor tab.
5. Click on the Change button.
6. In the Select Device Window, click the Have Disk
button.
7. Supply the location of inf file & click OK.
The default location is A:\. If you have copied the
file to a different drive, type the location in the
"Copy manufacturers files from" field.
8. From the list choose the appropriate Cornerstone
Monitor and click OK.
9. Once your selection appears in the Advanced Display
Properties Window, click on OK.
10. Click Apply and then the OK button to save the changes.
11. Adjust your monitor as needed. Consult your Cornerstone
Display Manual for further information on adjusting
screen size & position.
SECTION 3 -- Installing In Windows 98
=================================================
NOTE: Be sure to exit all applications before starting
the setup.
1. Begin by going to your Display Properties Page. You can do
this by right clicking on your desktop & selecting Properties
or by going to the Control Panel & Double Clicking on the
Display icon.
2. Go to the Settings tab.
3. Click the Advanced button.
4. Go to the Monitor tab.
5. Click on the Change button.
6. This will start the Update Device Driver Wizard. Click Next.
7. Select "Display a list of drivers in a specific location,
so you can select the driver you want". Click Next.
6. Click on the Have Disk button.
7. Supply the location of inf file & click OK.
The default location is A:\. If you have copied the
file to a different drive, type the location in the
"Copy manufacturers files from" field.
8. From the list choose the appropriate Cornerstone
Monitor and click Next.
9. You should now see your Cornerstone monitor model and driver
location. If the wrong information appears then click the
Back button and repeat steps 6-8. If the correct model is
listed here then click next and Windows 98 will install
your monitor driver.
10. When it's done click on the Finish button. Click Apply and
then the OK button to save the changes.
11. Adjust your monitor as needed. Consult your Cornerstone
Display Manual for further information on adjusting
screen size & position.
Section 4 -- Installing in Windows Me
=================================================
NOTE: Be sure to exit all applications before starting
the setup.
1. Begin by going to your Display Properties Page. You can do
this by right clicking on your desktop & selecting Properties
or by going to the Control Panel & Double Clicking on the
Display icon.
2. Go to the Settings tab.
3. Click the Advanced button.
4. Go to the Monitor tab.
5. Click on the Change button.
6. Select "Specify the location of the the driver". Click Next.
7. Select "Display a list of all the drivers in a specific
location, so you can select the driver you want." Click Next.
8. Click on the Have Disk button.
9. Supply the location of inf file & click OK.
The default location is A:\. If you have copied the
file to a different drive, type the location in the
"Copy manufacturers files from" field.
10. From the list choose the appropriate Cornerstone
Monitor and click Next.
11. You should now see your Cornerstone monitor model
and driver location. If the wrong information appears then
click the Back button and repeat steps 8-10. If the correct
model is listed here then click next and Windows Me will
install your monitor driver.
12. When it's done click on the Finish button. Click Apply and
then the OK button to save the changes.
13. Adjust your monitor as needed. Consult your Cornerstone
Display Manual for further information on adjusting
screen size & position.
Section 5 -- Installing In Windows 2000
================================================
NOTE: Be sure to exit all applications before starting
the setup.
1. Begin by going to your Display Properties Page. You can do
this by right clicking on your desktop & selecting Properties
or by going to the Control Panel & Double Clicking on the
Display icon.
2. Go to the Settings tab.
3. Click the Advanced button.
4. Go to the Monitor tab.
5. Click on the Properties button.
6. This will open the Monitor Properties. Select the Driver tab.
7. Click the Update Driver button.
8. This will start the Update Device Driver Wizard. Click Next.
9. Select "Display a list of the known drivers for this device
so that I can choose a specific driver" and click Next.
10. Click on the Have Disk button.
11. Supply the location of inf file & click OK.
The default location is A:\. If you have copied the
file to a different drive, type the location in the
"Copy manufacturers files from" field.
12. From the list choose the appropriate Cornerstone
Monitor and click Next.
13. You should now see your Cornerstone monitor model. If the
wrong information appears then click the Back button and
repeat steps 10-12. If the correct model is listed here
then click next and Windows 2000 will install your monitor
driver. You may be prompted with a warning about a this driver
not having a Microsoft Digital Signature. Click on the
Yes button to continue with the installation.
14. When it's done click on the Finish button. Adjust your monitor
as needed. Consult your Cornerstone Display Manual for further
information on adjusting screen size & position.
Section 6 -- Installing In Windows XP
================================================
NOTE: Be sure to exit all applications before starting
the setup.
1. Begin by going to your Display Properties Page. You can do
this by right clicking on your desktop & selecting Properties
or by going to the Control Panel & Double Clicking on the
Display icon.
2. Go to the Settings tab.
3. Click the Advanced button.
4. Go to the Monitor tab.
5. Click on the Properties button.
6. This will open the Monitor Properties. Select the Driver tab.
7. Click the Update Driver button.
8. This will start the Hardware Update Wizard. Select "Install
from a list or specific location (Advanced)". Click Next.
9. Select "Don't search. I will choose the driver to install".
Click Next.
10. Click on the Have Disk button.
11. Supply the location of inf file & click OK.
The default location is A:\. If you have copied the
file to a different drive, type the location in the
"Copy manufacturers files from" field.
12. From the list choose the appropriate Cornerstone
Monitor and click Next.
13. You should now see your Cornerstone monitor model. If the
wrong information appears then click the Back button and
repeat steps 10-12. If the correct model is listed here
then click next and Windows XP will install your monitor
driver. You may be prompted with a warning about this software
"has not passes Windows Logo testing to verify its
compatibility with Windows XP". Click on the "Continue Anyway"
button to continue with the installation.
14. When it's done click on the Finish button. Adjust your monitor
as needed. Consult your Cornerstone Display Manual for further
information on adjusting screen size & position.
---------------------------------------------------------
Cornerstone Customer Support
====================================
If you need technical assistance please contact Cornerstone
Customer Support at the following numbers:
Email: support@cptmail.com
Customer Support in USA: 1 800 562 2552
Technical Support in USA: 1 888 338 6490
Headquarters in USA: 1 510 580 8900
Fax: 1 510 580 8998
Support Home Page: http://www.bigmonitors.com
To Purchase
Cornerstone Products: http://www.monitorsdirect.com
All Trademarks are property of their respective owners.
Microsoft Windows, and Internet Explorer is a trademark of
the Microsoft Corporation. Copyright (C), Cornerstone Peripherals
Technology.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.