Please find the English text below ! Installation von VTPlus für WinTV 32 Bit Version 2.6x ===================================================== Bevor VTPlus 32 installiert werden kann, muß die WinTV-Karte betriebsbereit und die WinTV32 Software installiert sein. Alternativ können Sie auch einen Treiber auswählen, damit VTPlus mit der 16 Bit Version der WinTV Software zusammenarbeitet, falls diese auf Ihrem Computer installiert sein sollte. Die folgende Beschreibung brauchen Sie dann nicht zu lesen. Außerdem erfordert VTPlus, daß eine Channel Suite mit dem Namen "VTPlus" mit dem Channel Suite Manager von WinTV32 eingerichtet wird. Weitere Informationen zu diesem Thema werden beim Start von VTPlus sowie innerhalb des Dialogs zum Senderwechsel angezeigt. VTPlus 32 setzt voraus, daß Ihr Computer für Software Teletext geeignet ist, sowie die dazu nötigen Treiber bereits installiert sind. Die WinTV Karte und die darauf eingestellten Fernsehsender sind Resourcen, die nur bedingt von mehreren Programmen gleichzeitig benutzt werden können. VTPlus ist per Voreinstellung für die optimale Zusammenarbeit mit anderen Programmen, z. B. der WinTV32 Software eingestellt: VTPlus initialisiert die WinTV Karte beim Start so, daß auch andere Programme sie parallel benutzen können. Dies hat zur Folge, daß beim Senderwechsel nur Tunerkanäle umgeschaltet werden können, die Umschaltung zu anderen "Input Sources", wie Composite oder SVideo und zurück zum Tuner ist nicht möglich. Um dieses Verhalten zu ändern legen Sie bitte in der Datei vtplus32.ini im Windows-Verzeichnis folgenden Eintrag an: [hcwcmx] Exclusive=1 Dies gibt VTPlus die volle Kontrolle über die WinTV Karte. Somit wird auch die Umschaltung zu anderen "Input Sources", wie Composite oder SVideo und zurück zum Tuner möglich. Eine andere Software kann aber nicht mehr parallel zu VTPlus die WinTV Karte verwenden, wenn sie nach VTPlus gestartet wird. Falls aber bereits eine andere Software die WinTV Karte verwendet, startet VTPlus normal ohne die volle Kontrolle über die WinTV Karte zu übernehmen. =============================================================================== English Text: =============================================================================== Installation of VTPlus for WinTV 32 Bit Version 2.6x ==================================================== Before VTPlus can be installed, your WinTV card must be ready-to-run and the WinTV32 software must be installed. You also can select a driver, that enables VTPlus to run together with the 16 bit version of the WinTV software, if it is installed on your computer. You should not read the following description then. Further VTPlus requires a channel suite named "VTPlus" being set up with the Channel Suite Manager of WinTV32. More information about this will be displayed at the start of VTPlus or with the dialogue for switching channels. VTPlus 32 assumes that your Computer is suitable for Software Teletext and the necessary drivers therefor are already installed. The WinTV card and the channels set up on it are resources that can only partially be shared among different programs at the same time. VTPlus is set up by default to work together with other programs like the WinTV32 software: VTPlus will initialise the WinTV card at the start in a mode, that allows also other programs to use it at the same time. In that mode only tuner channels can be switched, however. VTPlus will not be able to switch to other Input Sources like Composite or SVideo and back to the Tuner. To change this behaviour please add the following entry to the file vtplus32.ini in the Windows directory: [hcwcmx] Exclusive=1 This gives VTPlus full control over the WinTV card. So it becomes possible also to switch to other Input Sources like Composite or SVideo and back to the Tuner. But another software cannot use the WinTV card at the same time with VTPlus then, if it is started after VTPlus. If another software using the WinTV card is already running, VTPlus will start as usual without gaining full control over the WintV card.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.