Please find the English text below ! Zusätzliche Schalter für VTPlus =============================== Die Einstellungen zum normalen Betrieb können im VTPlus Programm unter Optionen vorgenommen werden. In besonderen Fällen ist jedoch ein spezielles Verhalten des Programmes gewünscht. Dieses können Sie durch Eintragungen in der Steuerdatei für VTPlus (vtplus32.ini im Windows-Verzeichnis) bewirken. In der Regel sollten die Voreinstellungen nicht geändert werden, da Nebenwirkungen nicht ausgeschlossen sind. Die zusätzlichen Programmschalter sind in späteren Versionen von VTPlus unter Umständen nicht mehr vorhanden. Folgende Schalter sind derzeit verfügbar: Abschnitt [vtplus]: BmpBits ======= mögliche Werte 4, 8, 16, 24 Voreinstellung 4 Beim Export einer Seite als farbige BMP-Grafik kann die Anzahl der Bits pro Pixel eingestellt werden. Somit sind Bitmaps mit 16, 256, 65536 oder 16 Mio. Farben möglich. Der Schalter dient zur Anpassung an Konvertierprogramme, z. B. cjpeg.exe, die Bitmaps mit bestimmtem Format erwarten. ExtDlg ====== mögliche Werte 0 oder 1 Voreinstellung 0 Bei Einstellung 1 kann beim Dialog Empfangen auch der Umfang der Unterseiten eingestellt werden. HexTransparent ============== mögliche Werte 0 oder 1 Voreinstellung 0 Bei Einstellung 1 wird beim Empfang von Seiten mit hexadezimalen Nummern keine Auswertung des Parity-Bits vorgenommen. Die Seiten können dann nicht mehr am Bildschirm angesehen werden, aber zur weiteren Auswertung der Daten gespeichert werden. Manche Decoder werten das Parity-Bit selbst aus. Der Schalter ist in diesem Fall ohne Wirkung. ReadDelay ========= mögliche Werte 0 bis 2000 Voreinstellung 0 Der eingestellte Wert wird als Verzögerung in Millisekunden beim Lesen einer Seite vom Decoder verwendet, wenn diese als empfangen gemeldet ist. Dies kann bei manchen Sendern nötig sein, die einzelne Seiten mit niedriger Priorität senden. Symptom: Ein Stück im unteren Teil der Seite bleibt schwarz. Die Verzögerung wirkt sich auf den Empfang insgesamt aus, der Wert sollte daher nur vorsichtig erhöht werden. Kann nicht für PCVTXpro Decoder und WinTV Software Teletext angewendet werden. Xlate ===== mögliche Werte 0 oder 1 Voreinstellung 0 Bei Einstellung 1 werden beim Exportieren englische Sonderzeichen für ¼, ½ und ¾ in .25, .50. und .75 konvertiert. Abschnitt [preload] CacheDir ======== Verzeichnis, in dem der Inhalt des Hintergrundspeichers beim Senderwechsel oder Programmende gespeichert wird. Voreinstellung <vtplus>\cache, d. h. Unterverzeichnis Cache im VTPlus Verzeichnis Abschnitt [batch]: Editor ====== Programm das zum Editieren von Scripts verwendet wird. Voreinstellung notepad.exe =============================================================================== English Text: =============================================================================== Additional Switches for VTPlus ============================== The settings for normal operation may be done inside the VTPlus program using the Options menu. In special cases you might however wish a special behaviour of the program. This may be done by enties in the VTPlus control file (vtplus32.ini in the Windows Directory). Normally the default settings should not be altered, because side effects may occur. The addional switches may no longer exist in future versions of VTPlus The following switches are present: Section [vtplus]: BmpBits ======= Possible values 4, 8, 16, 24 Default 4 When exporting a page as a colour BMP-Image the number of bits per pixel can be set. Thus bitmaps with 16, 256, 65536 oder 16 million colours are possible. The switch is used for adaptation to converters e. g. cjpeg.exe, that need bitmaps with a special format. ExtDlg ====== Possible values 0 or 1 Default 0 If set to 1 also the subpage range can be input in dialog Create and Receive. HexTransparent ============== Possible values 0 or 1 Default 0 When set to 1 the parity bit is ignored when receiving pages with hexadecimal numbers. The page then cannot be diplayed on the screen, but be saved as data for further processing. Some decoders process the parity bit at hardware level. In these cases the switch does not work. ReadDelay ========= Possible values 0 to 2000 Default 0 The value is used as a delay in milliseconds when a page is being read from the decoder after it is reported as received. This may be needed as some tv stations transmit some pages with low priority: If a part of the pages is black you may carefully increase this value. Cannot be used with PCVTXpro Decoders and WinTV Software Teletext. Xlate ===== Possible values 0 or 1 Default 0 If set to 1 English special characters for ¼, ½ and ¾ are exported as .25, .50. and .75. Section [preload] CacheDir ======== Directory which is used to store the contents of the background memory when channels are switched or VTPlus is ended. Default <vtplus>\cache, the subdirectory cache in the VTPlus directory. Section [batch]: Editor ====== Program that is used to edit scripts. Default notepad.exeDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.