TRENDware TE-PCI/TE-100PCI Ethernet Adapter Installation for SCO OpenServer V5.0 MDI Driver Contents ÄÄÄÄÄÄÄÄ Introduction Requirements Minimum Skill Level Getting Started Introduction ÄÄÄÄÄÄÄÄÄÄÄÄ This installation assumes that the adapter is working properly. Getting Started will describe the installation instructions. Requirements ÄÄÄÄÄÄÄÄÄÄÄÄ A PCI compatible computer A PCI Family Series Adapter A knowledge of basic UNIX commands and editing text files Minimum Skill Level ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ A knowledge of basic UNIX commands A knowledge of editing text files A knowledge of UNIX basic file structure A knowledge of the network driver configuration being used Getting Started ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 0. Login as root user. (On maintenance mode) 1. Using "custom" to install the driver 1.1 Prepare an image file Copy tep.img onto SCO OpenServer and rename it to VOL.000.000 # mkdir /usr/test # doscp a:/<PATH>/tep.img /usr/test/VOL.000.000 * <PATH> is the driver directory 1.2 Execute "custom" /* A menu selection screen will be popped up */ Using [->] key to move cursor to "Software" menu item then press [] key to get into pull down menu then move to "Install New..." then press [ENTER] key ÉÍÍÍÍÍÍÍÍÍÍ Begin Installation on scoopen ÍÍÍÍÍÍÍÍÍÍ» º º º What host (machine) do you want to install from? º º º º ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ º º ³<*> From scosysv ³ º º ³< > From another host ³ º º ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ º º º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º[ Continue ] [ Cancel ] [ Help] º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Select From scosysv and use [TAB] key to move cursor to [ Continue ] then press [ENTER] key and press [] key to get into pull down menu ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Select Media ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º º Insert media, and select media device. º º º º ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ º º Media Device:³|Floppy Disk Driver 0_____________________|v³ º º ÀÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ º º ºÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿º º º º³*Floppy Disk Driver 0 ³º º º º³ Media Images ³º º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º[ Continue ] ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ [ Help ]º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ -> Select "Media Images" and use [TAB] key to move cursor to [ Continue ] then press [ENTER] key then press [ENTER] key again ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Enter Image Directory ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º º Enter the full path to the directory containing media images. º º º º Image Directory: |/usr/test______________________________________| º º º º Note: media images must follow the naming convention º º VOL.000.000, etc. º º º º º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º[ OK ] [ Cancel ] [ Help ]º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ -> Input the path name where VOL.000.000 is located as above path name is /usr/test ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Enter Image Directory ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º º Installing: TRENDware TE-PCI/TE-100PCI Family device driver (version 3.1.1) º º º º Do you want a FULL or PARTIAL installation? º º º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º[ Full ] [ Partial ] [ Cancel ] [ Help ]º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Using [TAB] key to move cursor to [ Full ] then press [ENTER] key After the installation progress the following message is displayed ÉÍÍÍÍÍÍÍÍÍÍÍ Question ÍÍÍÍÍÍÍÍÍÍ» º Installation complete º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º [ OK ] º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Press [Enter] key then you will find out that TRENDware TE-PCI/TE-100PCI Family device driver (ver 3.1.1) is added to the package list Using [<-] key to move cursor back to "Host" menu item then press [] key to get into pull down menu then move to "Exit" then press [ENTER] key Now that the driver is installed in the system successfully. 2. Using "netconfig" to configure the driver /* A menu selection screen will be popped up */ At "Hardware" menu item press [] key to get into pull down menu then move to "Add new LAN adapter" then press [ENTER] key If you got a PCI NIC inserted on your machine, it will list as following: ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Add new LAN adapter ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» ºThe following adapters have been found: º ºÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿º º³* TRENDware TE-PCI/TE-100PCI Ethernet Adapter Compatible-PCI Bus#0,PCI Device#1 ³º º³ ³º º³ ³º º³ ³º º³ ³º ºÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙº º[ Configure hardware not listed above... ] º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º[ Continue ] [ Cancel ] [ Help ]º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Using [TAB] key to move to "Configure hardware not listed above..." then press [ENTER] key ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Add new LAN adapter ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» ºSelect network adapter to be added: º ºÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿º º³* 3Com EtherLink 16/16TP Adapter ^º º³ . *º º³ . *º º³ . *º º³ . *º º³ . *º º³ . *º º³ . *º º³ TRENDware TE-PCI Ethernet Adapter *º º³ TRENDware TE-100PCI Ethernet Adapter *º º³ . ³º º³ . ³º º³ . ³º º³ . ³º º³ . ³º º³ . vº ºÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙº ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º[ Continue ] [ Cancel ] [ Help ]º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Using [] key to move to "TRENDware TE-PCI Ethernet Adapter" or "TRENDware TE-100PCI Ethernet Adapter" depend on which card you want to configure, then press [ENTER] key. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Network Driver Configuration ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º ºEnter the configuration of TRENDware TE-PCI/TE-100PCI Ethernet Adapter:º º º º ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ [ Advanced ] º º PCI Bus#: ³| 0_______________________|v³ Options... º º ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ º º ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ º º PCI Device#: ³| 0_______________________|v³ º º ÀÉÍÍÍÍÍÍÍÍ»ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ º º ÚºÚÄÄÄÄÄÄ¿ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ º ºPCI Function#: ³º³ 9 ^º________________|v³ º º Àº³ 10 ³ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ º º º³ 11 ³º º º * - indicates º³ 12 *ºith other hardware º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ³* 13 *ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º[ OK ] º³ 14 vº [ Cancel ] [ Help ]º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͺÀÄÄÄÄÄÄÙºÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÈÍÍÍÍÍÍÍͼ The above screen let you fill the information of where your PCI adapter is located by specifying PCI Bus#, PCI Device# and PCI Function#. Note1: If you can not make sure the PCI parameters or your PCI Device# can not be found in the list, just leave them as default values, continue the following installation, after the driver is installed and system is re-linked, reboot the system then driver will search PCI Ethernet card automatically. "Advanced Options" let you specify what media type is connected. If you select it the following screen will be popped up ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Advanced Network Driver Configuration ÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º ºEnter the configuration of TRENDware TE-PCI/TE-100PCI Ehternet Adapter:º º º º ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ º ºMedia: ³| SROM_default_________|v³ º º ÀÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»ÄÄÄÄÄÙ º º º ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿º º º * - inº ³* SROM_default ^ºh other hardware º ºÄÄÄÄÄÄÄÄĺ ³ Auto *ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º[ OK º ³ TP *º [ Cancel ] [ Help ]º ÈÍÍÍÍÍÍÍÍͺ ³ TP_FD vºÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ º ³ 100TX *º º ³ 100TX_FD *º º ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙº ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Select the connective media then press [ENTER] key to go back to "Network Driver Configuration" screen. Using [TAB] key to move cursor to "OK" then press [ENTER] key. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Information ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º--- Please verify adapter is set to the configuration just enteredº ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º [ OK ] º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Press [ENTER] key. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Add Protocol ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» ºSelect one networking product to be added to º ºTRENDware TE-100PCI Ethernet Adapter: º ºÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿º º³ HW TRENDware TE-100PCI Ethernet Adapter ³º º³* - SCO IPX/SPX ³º º³ - SCO TCP/IP ³º º³ ³º º³ ³º ºÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙº ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º[ Add ] [ Cancel ] [ Help ]º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Using [] key to move cursor to "SCO TCP/IP" then press [ENTER] key. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ SCO TCP/IP Configuration ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º º º º º º º º º Local Host Name: |scoopen_____________| [ Advanced ]º º IP Address: |192.9.200.1_________| Options... º º Netmask: |255.255.255.0_______| º ºBroadcast Address: |192.9.200.255_______| º º Domain Name: |scoopen.com_________| º º TCP connections: |256_________________| º º Pseudo ttys: |32__________________| º º º º º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º º º [ OK ] [ Cancel ] [ Help ]º º º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Input the required information then use [TAB] key to move cursor to "OK" then press [ENTER] key. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Message ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º The following products were successfully configured into the system º º SCO TCP/IP º º TRENDware TE-100PCI Ethernet Adapter - PCI Bus#0,PCI Device#13,PCI Funcº º º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º[ OK ] [ Help ]º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Press [ENTER] key At "Hardware" menu item press [] key to get into pull down menu then move to "Exit" then press [ENTER] key ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ Question ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º The Unix Kernel must be re-linked before the changesº º??? made here will have an effect. º º Do you want to re-link the kernel now? º ºÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ º [ YES ] [ NO ] º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Press [ENTER] key Do you want this kernel to boot by default (y/n) y Do you want the kernel environment rebuilt (y/n) y 3. Reboot unix # shutdown -y -g0 *************************************************** * Another way to specify driver's PCI parameters * *************************************************** . Another way to modify PCI parameters is at booting time, shown as below: 1. Specify PCI Bus#, PCI Device# and PCI Function# Boot : unix net.mdi=tep(0) net.params=(pcb:0,pcd:14,pcf:0) 2. Auto-search PCI adapter card Boot : unix net.mdi=tep(0) Note2: The IRQ number must match with the value set in ROM-BIOS before you specify this value, please check it. The IRQ for PCI bus can be accessed by pressing [DEL] key when system is power on and choose the proper select item to set IRQ for PCI bus. Example: ROM PCI/ISA BIOS (2A4X5C31) PCI/GREEN FUNCTION SETUP AWARD SOFTWARE, INC. Press [DEL] key --> PCI/GREEN FUNCTION SETUP Slot 3 Using INT# : A-PIRQ1 . . . PIRQ1# Connect IRQ: 5 By Single ~Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.