1. AT2560TXv20.ZIP Driver
2. DIAG.TXT File Contents

DIAG.TXT Driver File Contents (AT2560TXv20.ZIP)

   Adapter diagnostics
                                                                 a1.03


ATI diagnostic software lets you test the adapter to see if there are
any problems with the adapter hardware, the cabling, or the network.

It's a good idea to run diagnostics every time you install an adapter.
You can also use diagnostics to isolate problems during troubleshooting.


DOS and Windows* 3.1 users
==========================

Note: If you want to test the adapter with a responder on the network,
      skip to the procedure after step 5.

1.  Restart your computer before loading any network drivers.
   
    Note: If drivers are installed, you must remove them or disable them
         and reboot your computer before running the diagnostic software.

2.  Insert the Configuration and Driver diskette into a drive,
    switch to that drive, and at the DOS prompt, type
      
      SETUP <Enter>

3.  From the Board Menu, select the adapter you want to test. (If you have
    only one adapter installed, the Board Menu doesn't appear.)

4.  From the Main Menu, select Test adapter. Then select Test adapter
    again. The program runs a series of tests that make sure the adapter
    is functioning properly.

5.  Repeat steps 3, 4, and 5 for each adapter installed in the computer.


To test the adapter with a responder on the network
---------------------------------------------------

1.  Go to a computer on the same network segment with another AT-2560 PCI
    adapter installed.

2.  If this computer already has adapter network drivers
    installed, restart the computer without loading them. For example, if
    the drivers are loaded from the AUTOEXEC.BAT file, add REM in front of
    each line that loads a driver. Or, boot from a DOS disk.

3.  Run the diagnostics program (SETUP.EXE) for the adapter that is
    installed in the computer.

4.  From the Main menu, select the command for testing the adapter, then
    select Set up as diagnostics responder.

5.  Return to the computer you want to test. Run SETUP, choose Test
    adapter, and then choose Continuous Network test.


Windows NT* users
=================

If you have not already installed new drivers from the
Configuration and Drivers Disk:

1.  Double-click the Network icon in the Control Panel.

2.  Click the Add Adapter button.

3.  Don't select an adapter from the list. Instead, scroll to the
    end of the list and select:
   
    <Other> Requires disk from manufacturer.

4.  Insert the Configuration and Drivers disk into your floppy
    drive.

    The A2560SET adapter setup program launches.

5.  Click the Test button.

   If you've just added the adapter, the network driver won't be active
   and the diagnostics will test the adapter and its connection to the
   network.

   If you're testing an adapter that's already been installed, the
   network driver will probably be active and the diagnostics will test
   the driver. This diagnostic tracks the driver's actual network
   activity.

If you have already installed the drivers:

1.   Double-click the A2560SET icon in the Control Panel.

2.   Click Test on the window that appears.

     If you have more than one adapter, first select the adapter from the
     displayed list.

   If you've just added the adapter, the network driver won't be active
   and the diagnostics will test the adapter and its connection to the
   network.

   If you're testing an adapter that's already been installed, the
   network driver will probably be active and the diagnostics will test
   the driver. This diagnostic tracks the driver's actual network
   activity.




Windows 95 users
================

Use the A2560SET adapter setup program to test the adapter:

1.   Double-click the A2560SET icon in the Control Panel.

2.   Click Test on the window that appears.

     If you have more than one adapter, first select the adapter from the
     displayed list.

When using the A2560SET adapter setup program, you have two testing
options:

A. Test the adapter and driver together:

The adapter and driver test doesn't require you to unload the NDIS
driver.

     a.   Click Test NDIS.

     b.   When the test is complete, click OK to exit.

B.   Test the adapter hardware:

The adapter hardware test unloads the NDIS driver.

     a.   Click Unload NDIS.

     b.   After the NDIS driver unloads, click OK to continue.

     c.   When the test is complete, click OK to exit. A2560SET reloads
          the driver.

     d.   Restart the computer. You must restart the computer before
          accessing any network drives.









*  Third-party trademarks are the property of their respective owners.