;*********************************************************************** ; Windows NT OEMSETUP.INF for ; ; ATI AT-2560 Series PCI/100 Ethernet Adapter ; ; A2560Set Version 1.4x ; Driver Version 2.x ; INF revision 25 (Disk version) ; ;*********************************************************************** [Identification] OptionType = NetAdapter [PlatformsSupported] ISA EISA MCA PCI "Jazz-Internal Bus" [LanguagesSupported] ENG [Options] A2560PCI [OptionsTextENG] A2560PCI = "Allied Telesyn AT-2560FX PCI/100 Ethernet Adapter" [FileConstants] DrvName = "A2560" ExeName = "A2560SET" Sp1Name = "A2560DI" Sp3Name = "A2560DG" KddName = "A2560KDD" PciName = "A2560PCI" HlpName = "A2560SET" DllName = "A2560100" Manufacturer = "Allied Telesyn" ProductSoftwareName = "A2560" ProductSoftwareTitle = "ATI AT-2560FX PCI/100 Ethernet Adapter Driver" ProductSoftwareImagePath = "%SystemRoot%\System32\drivers\a2560.sys" NetRuleSoftwareType = "A2560Sys ndisDriver A2560Driver" NetRuleSoftwareBindForm = """A2560Sys"" yes no container" NetRuleSoftwareClass = {"A2560Driver basic"} NetRuleSoftwareBindable = {"A2560Driver A2560Adapter non exclusive 100"} Configure = "DIAG100_Configure" Detect = "DIAG100_Detect" Diagnose = "DIAG100_Diagnose" DLL = "A2560100.DLL" RegistryKey = "DIAG100_GetRegistryKey" Summary = "DIAG100_Resource_Summary" AdapterDescription = "DIAG100_GetAdapterDescription" InstallAnyway = "DIAG100_InstallAnyway" DeviceExist = "DIAG100_DeviceExist" Adapter = "ATI AT-2560FX PCI/100 Ethernet" Help = "A2560SET.HLP" ExeKeyName = $(!NTN_ServiceBase)"\A2560Set" ExeAdapterName = "A2560100" ExeParameters = "Parameters" ProductHardwareName = "A2560" ProductHardwareTitle = "ATI AT-2560FX PCI/100 Ethernet Adapter" NetRuleHardwareType = "A2560 A2560Adapter" NetRuleHardwareBindForm = " yes yes container" NetRuleHardwareClass = {"A2560Adapter basic"} ProductHardwareDescription = "ATI AT-2560FX PCI/100 Ethernet Adapter" FuncTitle = "ATI AT-2560FX PCI/100 Ethernet Adapter Setup" ProdSoftwareDescription = "ATI AT-2560FX PCI/100 Ethernet Adapter Driver" ProdHardwareDescription = "ATI AT-2560FX PCI/100 Ethernet Adapter" Disk1 = "ATI AT-2560FX PCI/100 Ethernet Driver Disk" ;----------------------------------------------------------------------------- BusNumber = "0,7,BusNumber,0,2,0,0,16,1" BusType = "0,7,BusType,0,2,5,2,5,1" BusTypeLocal = "0,7,BusTypeLocal,0,2,5,2,5,1" Eid = "0,7,Eid,0,2,0,0,4294967295,1" Fifo = "0,3,Fifo Depth,0,2,12,0,15,1" ForceDpx = "1,4,Duplex Mode,0,4,Half,Half,1,Full,2" MediaType = "0,7,MediaType,0,2,1,1,1,1" MsPciScan = "0,4,MsPciScan,0,2,1,0,1,1" NumCoalesce = "1,7,Coalesce Buffers,0,2,8,1,32,1" NumRfd = "1,7,Receive Buffers,0,2,16,1,1024,1" NumTbd = "0,3,Transmit Buffer Descriptors,0,2,64,1,65535,1" NumTbdPerTcb = "0,4,Transmit Buffers per Frame,0,2,8,1,16,1" NumTcb = "1,7,Transmit Control Blocks,0,2,16,1,80,1" Off = "1,3,Off Timer,0,2,2,1,65535,1" On = "1,3,On Timer,0,2,32768,1,65535,1" RxDmaCount = "0,4,RxDmaCount,0,2,0,0,63,1" RxFifo = "0,4,Receive Fifo Depth,0,2,8,0,15,1" Slot = "0,3,Slot,0,2,0,0,64,1" Speed = "1,7,Network Speed,0,4,100Mbps,100Mbps,100" Threshold = "0,7,Transmit Threshold,0,2,16,0,200,1" TxDmaCount = "0,4,TxDmaCount,0,2,0,0,63,1" TxFifo = "0,4,Transmit Fifo Depth,0,2,8,0,15,1" UnderrunRetry = "0,4,UnderrunRetry,0,2,1,0,3,1" PerfOptims = "0,4,PerfOptims,0,2,0,0,65535,1" UcodeSW = "0,7,UcodeSW,0,2,1,0,1,1" Adaptive_IFS = "0,7,Adaptive_IFS,0,2,1,0,255,1" Txmitwait = "0,7,Txmitwait,0,2,1,0,255,1" OLD_1BYTE = 139 OLD_2BYTE = 98 NETCARD_ID = 25227 ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion" ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters" UtilityInf = "UTILITY.INF" ParamInf = "NCPARAM.INF" subroutineinf = "SUBROUTN.INF" SoftwareType = "driver" NetRuleSoftwareUse = $(SoftwareType) Exit_Code = 0 NetEventDLL = "%SystemRoot%\System32\netevent.dll" IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll" ProductMajorVersion = "2" ProductMinorVersion = "0" ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion) [Files-Inf] 1, oemsetup.inf, SIZE=50000, RENAME=$(!UG_Filename) [Files-Driver] 1, NT\$(DrvName).SY_, SIZE=50000, RENAME=$(DrvName).SYS [Files-Exe] 1, NT\$(ExeName).EX_, SIZE=50000, RENAME=$(ExeName).EXE 1, NT\$(ExeName).CP_, SIZE=50000, RENAME=$(ExeName).CPL 1, NT\$(Sp1Name).DL_, SIZE=50000, RENAME=$(Sp1Name).DLL 1, NT\$(KddName).DL_, SIZE=50000, RENAME=$(KddName).DLL 1, NT\MFC30.DL_, SIZE=50000, RENAME=MFC30.DLL 1, NT\MSVCRT20.DL_, SIZE=50000, RENAME=MSVCRT20.DLL 1, NT\$(HlpName).HL_, SIZE=50000, RENAME=$(HlpName).HLP 1, NT\CTL3D32.DL_, SIZE=50000, RENAME=CTL3D32.DLL 1, NT\$(PciName).DL_, SIZE=50000, RENAME=$(PciName).DLL 1, NT\$(DllName).DL_, SIZE=50000, RENAME=$(DllName).DLL [Files-Exe-Drivers] 1, NT\$(Sp3Name).SY_, SIZE=50000, RENAME=$(Sp3Name).SYS 1, NT\$(Sp1Name).SY_, SIZE=50000, RENAME=$(Sp1Name).SYS 1, NT\$(KddName).SY_, SIZE=50000, RENAME=$(KddName).SYS [ProductType] STF_PRODUCT = Winnt STF_PLATFORM = I386 [GeneralConstants] from = "" to = "" ExitCodeOk = 0 ExitCodeCancel = 1 ExitCodeFatal = 2 KeyNull = "" MAXIMUM_ALLOWED = 33554432 RegistryErrorIndex = NO_ERROR KeyProduct = "" KeyParameters = "" TRUE = 1 FALSE = 0 NoTitle = 0 ExitState = "Active" OldVersionExisted = $(FALSE) DriverPath = $(!STF_NTPATH)\drivers [FileConstantsENG] ProCaption = "Windows NT Setup" ProCancel = "Cancel" ProCancelMsg = "Windows NT Networking is not correctly installed. "+ "Are you sure you want to cancel copying files?" ProCancelCap = "Network Setup Message" ProText1 = "Copying:" ProText2 = "To:" FunctionTitle = $(FuncTitle) ProductSoftwareDescription = $(ProdSoftwareDescription) ProductHardwareDescription = $(ProdHardwareDescription) [date] Now = {} ? $(!LIBHANDLE) GetSystemDate [Source Media Descriptions] 1 = $(Disk1) [Identify] read-syms Identification ; set !G:DebugOutputControl = 1 set Status = STATUS_SUCCESSFUL set Identifier = $(OptionType) set Media = #("Source Media Descriptions", 1, 1) Return $(Status) $(Identifier) $(Media) [ReturnOptions] set Status = STATUS_FAILED set OptionList = {} set OptionTextList = {} set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) in $(LanguageList) ifstr(i) $($1) == "" goto returnoptions endif set PlatformList = ^(PlatformsSupported, 1) Ifcontains(i) $($1) in $(PlatformList) goto returnoptions else set Status = STATUS_NOTSUPPORTED goto finish_ReturnOptions endif else set Status = STATUS_NOLANGUAGE goto finish_ReturnOptions endif returnoptions = + set OptionList = ^(Options, 1) set OptionTextList = ^(OptionsText$($0), 1) set Status = STATUS_SUCCESSFUL finish_ReturnOptions = + Return $(Status) $(OptionList) $(OptionTextList) [InstallOption] ; set !G:DebugOutputControl = 1 set Status = STATUS_FAILED set Option = $($1) set SrcDir = $($2) set AddCopy = $($3) set DoCopy = $($4) set DoConfig = $($5) set LanguageList = ^(LanguagesSupported, 1) Ifcontains(i) $($0) NOT-IN $(LanguageList) Return STATUS_NOLANGUAGE endif set-subst LF = "\n" read-syms GeneralConstants read-syms FileConstants ;read-syms DialogConstants$(!STF_LANGUAGE) ifstr(i) $(!NTN_Origination) == "NCPA" set Continue = "OK" endif read-syms FileConstants$(!STF_LANGUAGE) detect date set-title $(FunctionTitle) set CurrentVersionValue = "" OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion" $(!REG_KEY_READ) KeyWinNT ifstr(i) $(KeyWinNT) != "" GetRegValue $(KeyWinNT) "CurrentVersion" CurrentVersionValue CloseRegKey $(KeyWinNT) endif set m_WinNTVersion = *($(CurrentVersionValue),4) set to = Begin set from = Begin ifcontains(i) $(m_WinNTVersion) in {"3.50", "3.51"} ; WinNT 3.5x Shell $(UtilityInf), GetBusTypeNum ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif Set PlatformList = ^(PlatformsSupported, 1) Set MachineType = *($(PlatformList), $($R1)) else ; WinNT 4.x Set MachineType = $(!STF_BUSTYPE) endif set CommonStatus = STATUS_SUCCESSFUL EndWait Begin = + Set ActivateDetection = FALSE Ifstr(i) $(!NTN_InstallMode) == deinstall set StartLabel = removeadapter else-Ifstr(i) $(!NTN_InstallMode) == Update set StartLabel = UpgradeSoftware else-Ifstr(i) $(!NTN_InstallMode) == bind set StartLabel = bindingadapter else-Ifstr(i) $(!NTN_InstallMode) == configure set ActivateDetection = TRUE set StartLabel = configureadapter ifstr(i) $(MachineType) == "MCA" Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE else Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_HARDWARE endif set Error = $($R0) set from = end set to = end goto nonfatalinfo endif Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) set from = end set to = end goto nonfatalinfo endif else set ActivateDetection = TRUE set StartLabel = installadapter set OEM_ABANDON_OPTIONS = {} set OEM_ABANDON_SOFTWARE = FALSE set OEM_ABANDON_ON = TRUE endif Set DetectedCard = FALSE Ifstr(i) $(ActivateDetection) != TRUE Goto $(StartLabel) Endif ifstr(i) $(MachineType) == "MCA" goto CheckForMCA endif set IRQValue = *($(IRQList), 2) set IOAddrValue = *($(IOAddrList), 1) set IOReadyValue = *($(IOReadyList), 2) set TransceiverValue = *($(TransceiverList), 4) Ifstr(i) $(!STF_NCDETECT) == YES Ifstr(i) $(!STF_NCOPTION) == $(Option) Set DetectedCard = TRUE Endif Endif Shell "" DebugConfiguration "After parameter querying" Set from = $(fatal) Set to = $(fatal) Goto $(StartLabel) installadapter = + OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) CloseRegKey $(KeyProduct) ifstr(i) !(NTN_RegBase) == $(ProductKeyName) Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+ $(ProductVersion) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif goto end else Shell $(UtilityInf), CardExistedDlg ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) != "OK" goto end endif set OldVersionExisted = $(TRUE) endif endif ifcontains(i) $(m_WinNTVersion) in {"3.50", "3.51"} ; WinNT 3.5x Ifstr(i) $(DetectedCard) != TRUE Goto adaptersetup Endif else ; WinNT 4.x Goto adaptersetup end CheckForMCA = + StartWait Shell $(UtilityInf), MCAFindBus, $(OLD_1BYTE), $(OLD_2BYTE) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto CheckForISA endif ifstr $($R0) != "NO_ERROR" goto CheckForISA endif ifstr(i) $($R1) == {} set Error = $(CANNOT_FIND_ANY_CARD) set CommonStatus = USER_CANCEL set from = "end" goto nonfatal endif set AdapterList = $($R1) goto skipoptions CheckForISA = + Shell $(ParamInf) Param_QueryCard $(!STF_NCDETCARD) EndWait Ifstr(i) $($R0) != STATUS_SUCCESSFUL Goto adaptersetup Endif Set DetectedParams = $($R1) Shell $(ParamInf) Param_SetDefaults $(DetectedParams) goto adaptersetup configureadapter = + Ifstr $(KeyProduct) == $(KeyNull) OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE goto fatalregistry Endif Endif GetRegValue $(KeyProduct),"ServiceName", AdapterServiceKey set AdapterServiceKey = *($(AdapterServiceKey),4) Shell $(UtilityInf) FindService, $(KeyProduct) Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Endif Ifstr(i) $($R0) != NO_ERROR Goto fatalregistry endif Set KeyParameters = $($R2) CloseRegKey $($R1) Ifstr $(KeyParameters) == $(KeyNull) set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE goto fatalregistry endif set OldVersionExisted = $(TRUE) set ValueName = "" set ValueData = "" set ValueStr = "" set ValueList = {} adaptersetup = + Shell "" DebugConfiguration "before displaying dialog" Shell "" DebugConfiguration "After List Translation" Shell $(ParamInf) Param_ParameterConfidence Ifstr(i) $($R0) != STATUS_SUCCESSFUL Goto adapteroptions Endif Ifstr(i) $(DetectedCard) == TRUE Ifstr(i) $(!STF_INSTALL_MODE) != CUSTOM Goto adapterverify Endif Endif adapteroptions = + Set from = adapteroptions ;read-syms FileDependentDlg$(!STF_LANGUAGE) adapterverify = + ifcontains(i) $(m_WinNTVersion) not-in {"3.50", "3.51"} ; WinNT 4.x Goto skipoptions endif Shell "" DebugConfiguration "after running dialog" Ifstr(i) $(DetectedCard) != TRUE Goto skipoptions Endif Shell $(ParamInf) Param_VerifyCard $(!STF_NCDETCARD) Ifstr(i) $($R0) == STATUS_SUCCESSFUL Goto skipoptions Endif Set from = adapteroptions Set to = skipoptions Shell $(UtilityInf),RegistryErrorString,VERIFY_WARNING ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto Warning skipoptions = + ifint $(OldVersionExisted) == $(TRUE) ifstr(i) $(!NTN_InstallMode) == configure goto writeparameters endif endif StartWait ifint $(OldVersionExisted) == $(FALSE) ifstr(i) $(!NTN_InstallMode) == "install" Ifstr(i) $(DoCopy) == "YES" Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES Ifint $($ShellCode) != $(!SHELL_CODE_OK) Goto ShellCodeError Else-Ifstr(i) $($R0) == STATUS_FAILED Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal Else-Ifstr(i) $($R0) == STATUS_USERCANCEL Goto successful Endif Set SrcDir = $($R1) Endif install "Install-Option" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal endif endif Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), + $(ProductSoftwareName), + $(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), + $(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+ $(NetEventDLL) Set OEM_ABANDON_SOFTWARE = TRUE ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) set KeyProduct = $($R1) Set SoftNetRulesKey = $($R2) CloseRegKey $($R3) CloseRegKey $($R4) CloseRegKey $($R5) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) goto fatalregistry endif set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+ {MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+ {MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+ {Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} Shell $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) goto fatalregistry endif set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+ {use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, + {bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, + {bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareBindable)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(SoftNetRulesKey), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) CloseRegKey $(KeyProduct) CloseRegKey $(SoftNetRulesKey) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait goto fatalregistry endif endif ; Assume a single item in m_AdapterList except for ; if STF_NCDETECT is NO (Not using auto-detect, installing using the Add button). set m_AdapterList = {"Item1"} Ifstr(i) $(!NTN_InstallMode) == install Ifstr(i) $(!STF_NCDETECT) == YES ifcontains(i) $(m_WinNTVersion) not-in {"3.50", "3.51"} ; WinNT 4.x only set Vendor = 32902 ;; 0x8086 is 82557 Vendor ID set CFID = 4649 ;; 0x1229 is 82557 Device ID Shell $(UtilityInf), GetPCIInformation, $(Vendor) $(CFID) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R0) == {} set Error = $(CANNOT_FIND_ANY_CARD) set CommonStatus = USER_CANCEL set from = end goto nonfatal endif set m_AdapterList = $($R0) endif endif endif ForListDo $(m_AdapterList) ; Shell "Subroutn.Inf" SetupMessage $(!STF_LANGUAGE) "NONFATAL" "In For Loop!" Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName) ifint $($R4) != -1 Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4)) endif ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait CloseRegKey $($R1) CloseRegKey $($R2) CloseRegKey $($R3) goto fatalregistry endif set KeyParameters = $($R3) set KeyAdapterRules = $($R2) set AdapterNumber = $($R4) set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+ {Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardwareTitle)},+ {Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareDescription)},+ {ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+ {ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+ {InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}} set AdapterServiceKey = $($R5) Shell $(UtilityInf), AddValueList, $($R1), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif CloseRegKey $($R1) set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)"""" set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm) set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardwareType)},+ {bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, + {class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardwareClass)}, + {InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}} Shell $(UtilityInf), AddValueList, $(KeyAdapterRules), $(NewValueList) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR EndWait CloseRegKey $(KeyParameters) CloseRegKey $(KeyAdapterRules) goto fatalregistry endif CloseRegKey $(KeyAdapterRules) goto writeparameters writeparameters = + Shell $(UtilityInf), GetBusTypeNum set BusTypeNum = $($R1) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif Set IOAddrValue = *($(IOAddrValues), ~($(IOAddrList),$(IOAddrValue))) Shell "" DebugConfiguration "Before Writing Parameters" set NewValueList = {{Eid,$(NoTitle),$(!REG_VT_DWORD),0)}} Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList) CloseRegKey $(KeyParameters) OpenRegKey $(!REG_H_LOCAL) "" $(ExeKeyName)"\"Adapters $(MAXIMUM_ALLOWED) ExeAdapterKey ifstr $(ExeAdapterKey) == $(KeyNull) CreateRegKey $(!REG_H_LOCAL) {$(ExeKeyName)"\"Adapters,0,GenericClass} "" + $(MAXIMUM_ALLOWED) "" ExeAdapterKey ifstr $(ExeAdapterKey) == $(KeyNull) Shell "Subroutn.Inf" SetupMessage $(!STF_LANGUAGE) "NONFATAL" CreateRegAdapterFailed goto fatalregistry endif endif set NewValueList = {{$(ExeAdapterName),$(NoTitle), $(!REG_VT_SZ), $(Adapter)}} Shell $(UtilityInf), AddValueList, $(ExeAdapterKey), $(NewValueList) CloseRegKey $(ExeAdapterKey) OpenRegKey $(!REG_H_LOCAL) "" $(ExeKeyName)"\"$(ExeAdapterName) $(MAXIMUM_ALLOWED) ExeAdapterKey ifstr $(ExeAdapterKey) == $(KeyNull) CreateRegKey $(!REG_H_LOCAL) {$(ExeKeyName)"\"$(ExeAdapterName),0,GenericClass} "" + $(MAXIMUM_ALLOWED) "" ExeAdapterKey ifstr $(ExeAdapterKey) == $(KeyNull) Shell "Subroutn.Inf" SetupMessage $(!STF_LANGUAGE) "NONFATAL" CreateRegCardFailed goto fatalregistry endif endif set NewValueList = {{Configure,$(NoTitle),$(!REG_VT_SZ),$(Configure)},+ {Detect,$(NoTitle),$(!REG_VT_SZ),$(Detect)},+ {Diagnose,$(NoTitle),$(!REG_VT_SZ),$(Diagnose)},+ {DLL,$(NoTitle),$(!REG_VT_SZ),$(DLL)},+ {Help,$(NoTitle),$(!REG_VT_SZ),$(Help)},+ {RegistryKey,$(NoTitle),$(!REG_VT_SZ),$(RegistryKey)},+ {AdapterDescription,$(NoTitle),$(!REG_VT_SZ),$(AdapterDescription)},+ {InstallAnyway,$(NoTitle),$(!REG_VT_SZ),$(InstallAnyway)},+ {DeviceExist,$(NoTitle),$(!REG_VT_SZ),$(DeviceExist)},+ {Summary,$(NoTitle),$(!REG_VT_SZ),$(Summary)}} Shell $(UtilityInf), AddValueList, $(ExeAdapterKey), $(NewValueList) CloseRegKey $(ExeAdapterKey) OpenRegKey $(!REG_H_LOCAL) "" $(ExeKeyName)"\"$(ExeAdapterName)"\"$(ExeParameters) $(MAXIMUM_ALLOWED) ExeAdapterKey ifstr $(ExeAdapterKey) == $(KeyNull) CreateRegKey $(!REG_H_LOCAL) {$(ExeKeyName)"\"$(ExeAdapterName)"\"$(ExeParameters),0,GenericClass} "" + $(MAXIMUM_ALLOWED) "" ExeAdapterKey ifstr $(ExeAdapterKey) == $(KeyNull) Shell "Subroutn.Inf" SetupMessage $(!STF_LANGUAGE) "NONFATAL" CreateRegCardFailed goto fatalregistry endif endif set NewValueList = { + {BusNumber,$(NoTitle),$(!REG_VT_SZ),$(BusNumber)}, + {BusType,$(NoTitle),$(!REG_VT_SZ),$(BusType)}, + {BusTypeLocal,$(NoTitle),$(!REG_VT_SZ),$(BusTypeLocal)}, + {Eid,$(NoTitle),$(!REG_VT_SZ),$(Eid)}, + {Fifo,$(NoTitle),$(!REG_VT_SZ),$(Fifo)}, + {ForceDpx,$(NoTitle),$(!REG_VT_SZ),$(ForceDpx)}, + {MapRegisters,$(NoTitle),$(!REG_VT_SZ),$(MapRegisters)}, + {MediaType,$(NoTitle),$(!REG_VT_SZ),$(MediaType)}, + {MsPciScan,$(NoTitle),$(!REG_VT_SZ),$(MsPciScan)}, + {NumCoalesce,$(NoTitle),$(!REG_VT_SZ),$(NumCoalesce)}, + {NumRfd,$(NoTitle),$(!REG_VT_SZ),$(NumRfd)}, + {NumTbd,$(NoTitle),$(!REG_VT_SZ),$(NumTbd)}, + {NumTbdPerTcb,$(NoTitle),$(!REG_VT_SZ),$(NumTbdPerTcb)}, + {NumTcb,$(NoTitle),$(!REG_VT_SZ),$(NumTcb)}, + {Off,$(NoTitle),$(!REG_VT_SZ),$(Off)}, + {On,$(NoTitle),$(!REG_VT_SZ),$(On)}, + {RxDmaCount,$(NoTitle),$(!REG_VT_SZ),$(RxDmaCount)}, + {RxFifo,$(NoTitle),$(!REG_VT_SZ),$(RxFifo)}, + {Slot,$(NoTitle),$(!REG_VT_SZ),$(Slot)}, + {Speed,$(NoTitle),$(!REG_VT_SZ),$(Speed)}, + {Threshold,$(NoTitle),$(!REG_VT_SZ),$(Threshold)}, + {TxDmaCount,$(NoTitle),$(!REG_VT_SZ),$(TxDmaCount)}, + {TxFifo,$(NoTitle),$(!REG_VT_SZ),$(TxFifo)}, + {UnderrunRetry,$(NoTitle),$(!REG_VT_SZ),$(UnderrunRetry)}, + {PerfOptims,$(NoTitle),$(!REG_VT_SZ),$(PerfOptims)}, + {UcodeSW,$(NoTitle),$(!REG_VT_SZ),$(UcodeSW)}, + {Adaptive_IFS,$(NoTitle),$(!REG_VT_SZ),$(Adaptive_IFS)}, + {Txmitwait,$(NoTitle),$(!REG_VT_SZ),$(Txmitwait)}, + } Shell $(UtilityInf), AddValueList, $(ExeAdapterKey), $(NewValueList) CloseRegKey $(ExeAdapterKey) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif EndWait ifstr(i) $(!STF_GUI_UNATTENDED) == YES RunProgram ExitCode "" "" $(!STF_WINDOWSSYSPATH)\$(ExeName).EXE /BATCH $(AdapterServiceKey) else RunProgram ExitCode "" "" $(!STF_WINDOWSSYSPATH)\$(ExeName).EXE $(AdapterServiceKey) endif Ifstr(i) $(!NTN_InstallMode) != configure ifint $(ExitCode) >= 2 set CommonStatus = STATUS_USERCANCEL goto abandon endif else ifint $(ExitCode) == 0 set CommonStatus = STATUS_NO_EFFECT endif ifint $(ExitCode) == 2 set CommonStatus = STATUS_NO_EFFECT endif endif ; For auto-detect case, we need this ; For non-auto detect case, we still need this for the dummy item ; For all other, we don't need it Ifstr(i) $(!NTN_InstallMode) == install EndForListDo endif goto successful bindingadapter =+ set Error = "Binding: Sorry, not yet implemented." goto fatal removeadapter = + Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase) Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif else Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $(!NTN_RegBase) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif goto end UpgradeSoftware = + OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct Ifstr $(KeyProduct) != $(KeyNull) Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set !UG_Filename = $($R0) install "Install-Update" ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS goto fatal endif SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)} SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)} CloseRegKey $(KeyProduct) else goto fatalregistry endif goto end successful = + goto end abandon = + ForListDo $(OEM_ABANDON_OPTIONS) Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), + $(ProductSoftwareName), $($) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif EndForListDo Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE ; Remove Software Component Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), + $(ProductSoftwareName), FALSE ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set RegistryErrorIndex = $($R0) Ifstr(i) $(RegistryErrorIndex) != NO_ERROR goto fatalregistry endif endif goto end warning = + Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(to) else-ifstr(i) $($R1) == "CANCEL" goto $(from) else goto "end" endif nonfatalinfo = + Set Severity = STATUS Set CommonStatus = STATUS_USERCANCEL goto nonfatalmsg nonfatal = + Set Severity = NONFATAL goto nonfatalmsg nonfatalmsg = + ifstr(i) $(Error) == "" Set Severity = NONFATAL Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif ifstr(i) $($R1) == "OK" goto $(from) else goto "end" endif fatalregistry = + Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) goto fatal fataldetect = + Shell $(UtilityInf),RegistryErrorString,CANNOT_DETECT ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) Goto fatal fatal = + ifstr(i) $(Error) == "" Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL" ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif set Error = $($R0) endif Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error) ifint $($ShellCode) != $(!SHELL_CODE_OK) goto ShellCodeError endif goto setfailed ShellCodeError = + set DlgType = "MessageBox" set STF_MB_TITLE = "Error: "$(FunctionTitle) set STF_MB_TEXT = "Shell Code Error" set STF_MB_TYPE = 1 set STF_MB_ICON = 3 set STF_MB_DEF = 1 ui start "Error Message" goto setfailed setfailed = + set CommonStatus = STATUS_FAILED ifstr(i) $(OEM_ABANDON_ON) == TRUE set OEM_ABANDON_ON = FALSE goto abandon endif goto end end = + goto term term = + Return $(CommonStatus) [DebugConfiguration] ; Set InfName = "OEMNADIN.INF" return [Install-Option] set STF_VITAL = "" ifstr(i) $(AddCopy) == "YES" AddSectionFilesToCopyList Files-Driver $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers AddSectionFilesToCopyList Files-Exe $(SrcDir) $(!STF_WINDOWSSYSPATH) AddSectionFilesToCopyList Files-Exe-Drivers $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers endif ifstr(i) $(DoCopy) == "YES" set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList else ifcontains(i) $(m_WinNTVersion) not-in {"3.50", "3.51"} ; WinNT 4.x LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\NT\$(ExeName).EXE $(!STF_WINDOWSSYSPATH)\$(ExeName).EXE LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\NT\$(Sp1Name).DLL $(!STF_WINDOWSSYSPATH)\$(Sp1Name).DLL LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\NT\$(KddName).DLL $(!STF_WINDOWSSYSPATH)\$(KddName).DLL LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\NT\MFC30.DLL $(!STF_WINDOWSSYSPATH)\MFC30.DLL LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\NT\MSVCRT20.DLL $(!STF_WINDOWSSYSPATH)\MSVCRT20.DLL LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\NT\$(HlpName).HLP $(!STF_WINDOWSSYSPATH)\$(HlpName).HLP LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\NT\CTL3D32.DLL $(!STF_WINDOWSSYSPATH)\CTL3D32.DLL LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\NT\$(PciName).DLL $(!STF_WINDOWSSYSPATH)\$(PciName).DLL LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\NT\$(DllName).DLL $(!STF_WINDOWSSYSPATH)\$(DllName).DLL LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\NT\$(Sp3Name).SYS $(!STF_WINDOWSSYSPATH)\DRIVERS\$(Sp3Name).SYS LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\NT\$(Sp1Name).SYS $(!STF_WINDOWSSYSPATH)\DRIVERS\$(Sp1Name).SYS LibraryProcedure STATUS,$(!NCPA_HANDLE), CopySingleFile $(!STF_HWND) $(SrcDir)\NT\$(KddName).SYS $(!STF_WINDOWSSYSPATH)\DRIVERS\$(KddName).SYS endif endif Exit [Install-Update] set STF_VITAL = "" set STF_OVERWRITE = "VERIFYSOURCEOLDER" AddSectionFilesToCopyList Files-Driver $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH) AddSectionFilesToCopyList Files-Exe $(SrcDir) $(!STF_WINDOWSSYSPATH) AddSectionFilesToCopyList Files-Exe-Drivers $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers set !STF_NCPA_FLUSH_COPYLIST = TRUE CopyFilesInCopyList exitDownload Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.