Server: NetWare 3.12 server
AT-2560FX
NetWare* 3.12 Server Driver Installation Notes
==============================================
Location of driver: \NWSERVER\A2560.LAN
Location of NLMs: Novell's automated services.
MSM31X.NLM (v2.50 or later)
ETHERTSM.NLM (v2.50 or later)
Note: Rename MSM31X.NLM to MSM.NLM.
Sample load commands
====================
LOAD C:<PATH>\MSM
LOAD C:<PATH>\ETHERTSM
LOAD C:<PATH>\A2560 SPEED=100 FORCEDUPLEX=1 SLOT=n FRAME=ETHERNET_802.2
BIND IPX TO A2560 NET=xxxxxxxx
General Instructions
====================
1. Install NetWare 3.12 according to the NetWare 3.12 installation
manual.
2. Load the following NLMs:
MSM.NLM (v2.50 or later)
ETHERTSM.NLM (v2.50 or later)
Note: Rename MSM31X.NLM to MSM.NLM
Make sure you use these (or later) versions. Earlier versions may not
work properly.
3. If you can't log in to the server (before starting the server) copy
the A2560.LAN driver from the \NWSERVER directory on the
CardAssistant disk to the root directory of the server's hard drive.
If you can log into the server, copy the driver to the SYSTEM
subdirectory. If you do this, you won't need to specify a path on the
load line. If you copy it to another directory, make sure the LOAD
statement includes the correct path.
4. Start the server. At the server console, issue the load and bind
statement(s) in this order:
LOAD C:<PATH>\MSM
LOAD C:<PATH>\ETHERTSM
LOAD C:<PATH>\A2560 SPEED=100 FORCEDUPLEX=1 SLOT=x FRAME=ETHERNET_802.2
BIND IPX TO A2560 NET=xxxxxxxx
5. Add the load and bind statements you need to the server's
AUTOEXEC.NCF file so the adapter driver loads automatically each time
the server starts.
Hints and tips
==============
LOAD line parameters
--------------------
SPEED: Specifies the speed the driver uses (100 Mbps).
NOTE: You must set the SPEED parameter if you're setting
the FORCEDUPLEX parameter to either half or full.
Syntax: SPEED=n (n = 100)
FORCEDUPLEX:
Note: Use full-duplex support only when the adapter is connected
to a full-duplex hub.
Syntax: FORCEDUPLEX=n
Where n=1 half duplex
2 full duplex
Duplex modes:
Half duplex (default): The adapter performs one operation at a
time. It either sends or receives.
Full duplex: The adapter sends and receives packets at the same
time. This improves the performance of your adapter. Set duplex
mode to full duplex ONLY if you have a switch that supports full
duplex.
Example:
(100 Mbps full duplex):
FORCEDUPLEX=2 (Sets adapter to full duplex)
SPEED=100 (See SPEED parameter above)
SLOT: Specifies the PCI slot number.
For PCI adapters, SLOT is derived from bus number and device
location as defined by the PCI specification. One way to determine
the slot number is to load the driver from the command line.
You'll be prompted with valid device number(s) for the adapter(s).
Select one of them.
Syntax: SLOT=n (n = 1,2,3,4,...)
NOTE: Future versions of NetWare will use NBI (NetWare Bus
Interface) to determine the slot number. NBI will map the
slot number to a different slot number than SETUP.EXE on the
Installation and Driver disk reports.
NODE: Specifies a local administered address (LAA) unique to each
adapter. Use this option to provide your own unique node address
for the adapter. The node address is a 12-digit hexadecimal
number; the second digit must be one of the following digits: 2,
6, A, E.
Syntax: NODE=02a012345678
02 => LLA, 02 is set by the driver if not specified.
00 => Typical address (default)
FRAME: Configures the adapter to process one of the four valid NetWare
Ethernet frame types.
Syntax: FRAME=n
n = Ethernet_802.2
Ethernet_802.3
Ethernet_II
Ethernet_SNAP
Default: Ethernet_802.2
TXTHRESHOLD: Represents the threshold for transmits from extender SRAM
FIFO.
Syntax: TXTHRESHOLD=n (n = number of 8 bytes)
For example, 16 represents 16x8 (or 128 bytes). In this case,
the LAN controller transmits after copying 128 bytes from the
host memory.
Default: dynamically set
The maximum number you can specify is 200 (200x8=1600 bytes) which
ensures there will not be any underruns.
BIND line parameters
--------------------
NET:
NET=xxxxxxxx is the unique network address for that LAN segment.
The default frame type is 802.2. If your workstation needs to use
the 802.3 frame type, see the section later in this document about
using multiple frame types on one adapter.
Installing multiple adapters
----------------------------
- If you have multiple adapters in a single server, each adapter must
have a different NET number and SLOT number. Also, you may want to
name each adapter. For example:
LOAD C:\A2560 SPEED=100 FORCEDUPLEX=1 SLOT=3 NAME=LAN_A
BIND IPX TO LAN_A NET=222
LOAD C:\A2560 SPEED=100 FORCEDUPLEX=1 SLOT=4 NAME=LAN_B
BIND IPX TO LAN_B NET=333
- If you have problems loading the driver on multiple adapters and the
initialization fails due to "Insufficient RCBs," increase the number
of buffers allocated to the server. Add the following to STARTUP.NCF:
SET MINIMUM PACKET RECEIVE BUFFERS = 100 (or larger)
SET MAXIMUM PACKET RECEIVE BUFFERS = 500 (or larger)
The MINIMUM value you specify must be at least 30 times the number of
AT-2560 PCI adapters in the computer.
Recommended settings:
1-3 adapters: 100
4 adapters: 150
The MAXIMUM you can specify depends on the amount of memory in the
server, but it must be greater than the MINIMUM.
Installing one adapter with multiple frame types
------------------------------------------------
When binding multiple frame types to one adapter, enter a LOAD and BIND
statement for each frame type. Each LOAD statement uses the same SLOT
number, but each BIND statement needs a unique network number. You must
also include a name on each load line to avoid being prompted for the
adapter to bind IPX to.
Example:
LOAD C:\A2560 SPEED=100 FORCEDUPLEX=1 SLOT=3 FRAME=ETHERNET_802.3 NAME=LAN8023
BIND IPX TO LAN8023 NET=77777
LOAD C:\A2560 SPEED=100 FORCEDUPLEX=1 SLOT=3 FRAME=ETHERNET_802.2 NAME=LAN8022
BIND IPX TO LAN8022 NET=88888
* Third-party trademarks are the property of their respective owners.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.