ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ PLANET ENW-9501 Plus ³
³ Installation for Windows for Workgroups 3.11 Driver ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
A. Installing the DC21X4 Driver on Windows for Workgroups:
1. In the Windows for Workgroups Network Group, open the Network Setup
option.
2. In the Network Setup applet, press the [Drivers...] button.
3. In the Network Drivers applet, press the [Add_Adapter...] button.
4. Select the [Unlisted or Updated Network Adapter] option and click
[OK]
5. When the Insert Driver dialog box prompts you for a disk, insert the
driver installation diskette into the drive, press the [Browse...]
button and select the wfw311 sub_directory.
6. Select the adapter that matches your hardware
from the Network Adapters list
[Digital Semiconductor 21040 based Ethernet Controller]
[Digital Semiconductor 21041 based Ethernet Controller]
[Digital Semiconductor 21140 based 10/100 mbps Ethernet Controller]
[Digital Semiconductor 21142 based 10/100 mbps Ethernet Controller]
[Digital Semiconductor 21143 based 10/100 mbps Ethernet Controller]
[Digital Semiconductor EB40 21040 based Evaluation Board]
[Digital Semiconductor EB41 21041 based Evaluation Board]
[Digital Semiconductor EB140 21140 based Evaluation Board]
[Digital Semiconductor EB142 21142 based Evaluation Board]
[Digital Semiconductor EB143 21143 based Evaluation Board]
Select "Digital Semiconductor 21143 based 10/100 Mbps Ethernet
Controller".
7. For PCI adapters, the driver's [Setup..] option allows the user
to change the following driver's properties:
o BurstLength: Specify the length of the DMA data transfer within
a PCI burst (1dword = 4 bytes)
1_dword
2_dwords
4_dwords
8_dwords
16_dwords (default)
32_dwords
o Bus Number: Specify the PCI Bus Number the adapter is plugged in.
Should be modified only for adapter plugged over a
Pci to Pci bridge.
0 (default)
1
2
o ConnectionType: Specify the selected Media port
-----------------------------------------------------------------
Digital Semiconductor 2114x 10/100 Mbps Ethernet Controller
-----------------------------------------------------------------
o AutoSense Senses dynamically the media ports
o 10BaseT (TP)
o 10BaseT (TP) Full Duplex To connect to Full Duplex hubs
o 10Base2 (BNC) BNC connector
o 10Base5 (AUI) 15_pin connector
o 100BaseTx To connect 100BaseTx Ethernet hubs
o 100BaseTx Full_Duplex To connect 100BaseTx Full Duplex
hubs
o 100BaseT4 To connect 100BaseT4 Ethernet hubs
o 100BaseFx To connect 100BaseFx Ethernet hubs
o PciMechanism: Specify the mechanism access to the PCI
configuration space.
o AutoDetect Detect the system's PCI mechanism
automatically
o Mechanism 1 Force PCI mechanism #1 accesses to the
PCI configuration space
o Mechanism 2 Force PCI mechanism #2 accesses to the
PCI configuration space
o ReceiveBuffers: Specify the size of the receive buffer's ring
8 .. 64 (default 16)
o MapRegisters = REG_DWORD {4,8,16} (default: 8)
Number of map registers allocated
by the adapter.
o SnoozeMode = REG_DWORD { 0 | 1 }
CFDA<SM> 0 Disabled (default)
1 Enabled
o StoreAndForward = REG_DWORD { 0 | 1} (21140, 21143/2 only)
Select the StoreAndForward mode if high
PCI latencies causes 100Mbps Transmit Underruns
CSR6<SF> 1 Enabled
0 Disabled (default)
o TransmitThreshold = REG_DWORD { 72 | 96 | 128 | 160 }
Transmit Threshold value for 10Mbps media.
CSR6<TTM,TR> 72 bytes
96 bytes (default)
128 bytes
160 bytes
o TransmitThreshold100 = REG_DWORD { 128 | 256 | 512 | 1024 }
Transmit Threshold value for 100Mbps media.
CSR6<TTM,TR> 128 bytes
256 bytes
512 bytes (default)
1024 bytes
o UnderrunThreshold = REG_DWORD number_of_underruns (default=10)
(21140 and 21143/2 only)
Maximun number of underrun occurences before the
controller switches to StoreAndForward mode.
8. Click [Close] and [OK] to complete the driver installation.
9. Shutdown and reboot the system.
10. Installing multiple PCI boards:
Repeat the procedure above.
B. Error messages
The error messages are logged in the Entry Log.
Each error message has a standard Ndis error code and an driver's
additional code. The additional codes are:
DC21X4_ERRMSG_INIT_INTERRUPT 0x01
DC21X4_ERRMSG_CREATE_FILTER 0x02
DC21X4_ERRMSG_ALLOC_MEMORY 0x03
DC21X4_ERRMSG_INITIAL_INIT 0x04
DC21X4_ERRMSG_ALLOC_OPEN 0x05
DC21X4_ERRMSG_NETWORK_ADDRESS 0x06
DC21X4_ERRMSG_SYSTEM_ERROR 0x07
DC21X4_ERRMSG_TXM_JABBER_TIMEOUT 0x08
DC21X4_ERRMSG_OPEN_DB 0x09
DC21X4_ERRMSG_DEVICE_ID 0x0A
DC21X4_ERRMSG_INIT_DEVICE 0x0B
DC21X4_ERRMSG_SROM 0X0C
1. Driver initialization errors:
o NDIS_ERROR_CODE_ADAPTER_NOT_FOUND
DC21X4_ERRMSG_DEVICE_ID
No board matching the AdapterCFID Registry's key value was found
plugged into the PCI bus
o NDIS_ERROR_CODE_OUT_OF_RESOURCES
DC21X4_ERRMSG_ALLOC_MEMORY
Not enough memory to allocate space for the Adapter data block
o NDIS_ERROR_CODE_INVALID_VALUE_FROM_ADAPTER
DC21X4_ERRMSG_SROM
Invalid data read from the adapter's serial ROM
o NDIS_ERROR_CODE_NETWORK_ADDRESS
DC21X4_ERRMSG_NETWORK_ADDRESS
No readable burnt_in or software configured station address
o NDIS_ERROR_CODE_OUT_OF_RESOURCES
DC21X4_ERRMSG_CREATE_FILTER
Ethernet Filter initialization failed
o NDIS_ERROR_CODE_INTERRUPT_CONNECT
DC21X4_ERRMSG_INIT_INTERRUPT
Interrupt initilization failed
o NDIS_ERROR_CODE_TIMEOUT
DC21X4_ERRMSG_INIT_DEVICE
DC21x4 Cam initialization failed
o NDIS_ERROR_CODE_OUT_OF_RESOURCES
DC21X4_ERRMSG_ALLOC_OPEN
Not enough memory space to allocate space for the open binding.
o NDIS_ERROR_CODE_OUT_OF_RESOURCES
DC21X4_ERRMSG_OPEN_DB
Not enough memory space to allocate space for the Ethernet filter
2. Driver run time errors:
o NDIS_ERROR_CODE_HARDWARE_FAILURE
DC21X4_ERRMSG_SYSTEM_ERROR
System_Error interrupt (bus parity error)
o NDIS_ERROR_CODE_HARDWARE_FAILURE
DC21X4_ERRMSG_TXM_JABBER_TIMEOUT
Transmit Jabber timer expired
C. Driver revision number
The driver revision number is stored into the
protocol.ini file:
[DEC$DCxxx]
MajorDriverVersion
MinorDriverVersion
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.