NWCLNT32.TXT Driver File Contents (9501P-DriverDisk-v2.zip)

   ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
   ³                  Installation for NetWare Client 32                    ³
   ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

   A. Software Revision Requirements:

          o NetWare                      version 3.11 or above.
          o Novell support modules       as supplied in kit directories.

   B. Supplied Files:

      Table 1:  The  Novell NetWare ODI Server Directory Files
      ---------------------------------------------------------------------
      DC21X4.LAN      DC21X4 Novell NetWare ODI server driver.
                      ---------------------------------------------------
      DC21X4.LDI      Novell network installation file for this driver
                      ---------------------------------------------------
      DC21X4.INF      Novell network Windows 95 installation file for
                      this driver
      --------------------------------------------------------------------

   C. Installing Software:

      1. NetWare Client 32 Installation :

         1) Copy \NWSERVER\DC21X4.LAN into the NetWare Client 32
            subdirectory (default is C:\NOVELL\CLIENT32).

         2) Modify STARTNET.BAT in NetWare Client 32 subdirectory.
            For example :

            SET NWLANGUAGE=English
            C:\NOVELL\CLIENT32\NIOS.EXE
            LOAD C:\NOVELL\CLIENT32\LSLC32.NLM
            LOAD C:\NOVELL\CLIENT32\CMSM.NLM
            LOAD C:\NOVELL\CLIENT32\ETHERTSM.NLM
            LOAD C:\NOVELL\CLIENT32\DC21X4.LAN FRAME=ETHERNET_802.2
            LOAD C:\NOVELL\CLIENT32\DC21X4.LAN FRAME=Ethernet_802.3
            LOAD C:\NOVELL\CLIENT32\DC21X4.LAN FRAME=Ethernet_II
            LOAD C:\NOVELL\CLIENT32\DC21X4.LAN FRAME=Ethernet_SNAP
            LOAD C:\NOVELL\CLIENT32\IPX.NLM
            LOAD C:\NOVELL\CLIENT32\CLIENT32.NLM

      2. NetWare Client 32 for Windows 95 installation :

         1) Run SETUP from NetWare Client 32 for Windows 95 disk and follow
            on the setup instructions to install the NetWare Client 32 for
            Windows 95.

         2) When "Select Device" for Network Adapter dialog box is prompted,
            click "Have Disk".

         3) Type drv:\NWCLIENT\CLIENT32 to specify a different path in
            "Install From Disk" diaglogue box, click "OK".

         4) Go through NetWare Client 32 for Windows 95 installation
            procedures.


   D.  Parameters

       The following parameters belong on the server's command line, or in
       the load line inside the AUTOEXEC.NCF. The general way of using these
       parameters is:

            LOAD <driver name> <PARAMETER NAME>... <PARAMETER NAME[=VALUE]>

       Example:

            LOAD <driver name> TURBO SLOT=16 FRAME=Ethernet_802.2

        ------------------------------------------------------------------
        NOTE that wrong values (such as 'line_speed=128') are IGNORED, and 
             a default value is taken instead.
        ------------------------------------------------------------------

       Driver specific parameters list  (as for NetWare standard parameters,
       please see the NetWare user's manual):

            TP              selects TP port.

            TP_NO_LINK_TEST selects twisted pair connection, but disables
                            the LINK test for specific HUBs that do not
                            support LINK.

            TP_FULL_DUPLEX  selects twisted pair connection to work in
                            full duplex mode.

            TURBO           Fixes the problem of multiple transmit
                            underflows and receive overflows (i.e. lose
                            of packets) in systems that use certain PCI
                            chipsets.

            LINE_SPEED      selects line speed between 10MPBs and 100MBPs.

                            Format: LINE_SPEED=<value>

                            Allowed values are: 10,100

            GENERAL_PURPOSE_CONTROL
                            user override of the control value in the
                            GENERAL_PURPOSE register.
                            Normally, this value should not be changed.

                    Format: GENERAL_PURPOSE_CONTROL=<Hexadecimal Value>

                    Allowed values: in the range 1FF-0 hex.

            GENERAL_PURPOSE_DATA    user override of the data value in the
                                    GENERAL_PURPOSE register.
                                    Normally, this value should not be
                                    changed.

                    Format: GENERAL_PURPOSE_DATA=<Hexadecimal Value>

                    Allowed values: in the range 1FF-0 hex.


            NT              run under NT requester

            OS2             run in NetWare for OS/2

            Unixware        run in UnixWare

            Client32Win     run in Client32 environment for windows

            Client32Win95   run in Client32 environment for Windows95

            Client32DOS     run in Client32 environment for DOS

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: ftp, load: 2.67