** ** ** VIA PCI 10/100Mb Fast Ethernet Adapter ** ** SCOUNIX 3.2.4 Driver ** ** v3.12 May 2001 ** ** Introduction: ============= The Ethernet Driver for SCOUNIX confirms to the SCOUNIX LLI driver package format. This document shows you how to setup the SCOUNIX driver and how to use the enhanced functions by setting the custom keywords in configuration file. Contents of the Subdirectory: ============================= fetsco3.tar The SCOUNIX driver installation package in TAR format. fetsco3.txt This file. Installation: ============= Before starting with the installation process, make sure that the adapter is properly installed and configured. You can use the diagnostic program (A:\SETUP.EXE) to make sure your connection with the network is correct. Installation by using SCOUNIX custom utility: --------------------------------------------------------- 1) Make a sub-directory like fetsco3 ex: mkdir fetsco3 cd fetsco3 2) copy scounix\fetsco3.tar to harddisk in UNIX. (Use DOSCP command) ex: doscp -r a:/scounix/fetsco3.tar fetsco3.tar 3) uncompress fetsco3.tar with TAR command. ex: tar xvf fetsco3.tar 4) delete fetsco3.tar ex: rm fetsco3.tar 5) compress extracted files to a formatted floopy ex: tar cvf /dev/rfd0135ds18 . 6) Run CUSTOM utility in UNIX to install driver with this diskette.. ex: custom 7) Run netconfig to configure p3043 driver. ex: netconfig 8) when you running netconfig utility,you must select Driver mode (1.Auto 2.100 Full 3.100 Half 4.10 Full 5.10 Half),and Auto mode is default. 9) If you want to change Driver mode,you must run netconfig and select 3.Reconfigure an element in a chain.Select the driver and select Driver mode again.After you change the driver mode,you must link unix again. NOTE: ===== Multiple Lan Adapters in a system: If you want to install mutiple Lan adapter in your system, you have to use the keyword, Pciid1, Pciid2, Pciid3, Pciid4 respectively in \etc\conf\pack.d\p30430\space.c file to let driver locate the right adapter. You can run A:\SETUP.EXE under DOS prompt to show all the Ethernet addresses of your adapters. Configuration Files: ==================== File Name: \etc\conf\pack.d\p3043?\space.c (?=0,1,2,3) ---------- Sample of configuration file: ----------------------------- ... char *Pciid1="0"; char *Pciid2="0"; char *Pciid3="0"; char *Pciid4="0"; ... Pciid1 is the PCI ID of first PCI Ethernet adapter. Pciid2 is the PCI ID of second PCI Ethernet adapter. Pciid3 is the PCI ID of third PCI Ethernet adapter. Pciid4 is the PCI ID of fourth PCI Ethernet adapter. Pciid value "0" means use the first PCI Ethernet adapter found. So Pciid2, Pciid3, Pciid4 should not have value "0". Custom Keywords: ---------------- Pciid? = "hhhhhhhhhhhh" This keyword is the Ethernet Address of the adapter you want to drive. If there are more than one ethernet adapters in your system, you have to use this keyword to let driver locate the right adapter. However, you don't have to use this property or let the value to be zero (i.e. Pciid1 = "0") if there is only one adapter in your system. Note: For PCI mode adapter, you don't have to define IRQ and IOBASE value when you install your driver, for the driver will ignore these values.Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.