1. intel_10.zip Driver
2. BANYAN.TXT File Contents

BANYAN.TXT Driver File Contents (intel_10.zip)

   Banyan NDIS Workstation
                                                                    v1.00


Banyan* NDIS workstation installation notes for Intel's EtherExpress(TM)
10 ISA LAN adapters
========================================================================

Location of Driver:     \NDIS\EX10.DOS


Sample Configuration Files
--------------------------

CONFIG.SYS (will contain):
   DEVICE=C:\BAN\PROTMAN.DOS /I:C:\BAN
   DEVICE=C:\BAN\EX10.DOS

PROTOCOL.INI:
   [EX10_NIF]
   Drivername = EX10$
   IOADDRESS = 0x300


General Installation
--------------------

1  The EtherExpress(TM) 10 ISA LAN adapter uses an NDIS 2.0.1 driver to
   connect to a Banyan* server.  If you have an NDIS client disk
   prepared, skip to step #6.

2  To generate an NDIS client disk, run PCCOPY which is located on the Z
   drive of the Banyan server.

3  Choose PC Configuration Software and/or LAN driver, and select NDIS
   Ethernet.

4  Choose the appropriate DOS redirector (example: REDIRALL for all
   versions of DOS).

5  Specify the directory you want the client software copied to.  The
   default is A:\.

6  On the client you wish to set up, copy the NDIS client software to a
   directory on the hard drive.  Run Banyan's PCCONFIG program.  Select
   Network Card Settings and page down to select the NDIS Ethernet
   option.  Specify the Interrupt (as set in EX10Set) and the
   PROTOCOL.INI Bindings parameter: EX10_NIF.

7  Select Login Environment Settings, then Select Default Communications
   Driver.  Page down to the NDIS Ethernet option and select it.

8  Save settings before exiting PCCONFIG.

9  Copy the files PROTOCOL.INI and EX10.DOS that are located in the NDIS
   subdirectory of the EtherExpress 10 ISA LAN adapter disk to the BAN
   subdirectory (as per the example) or other directory where Banyan
   client files are located.  Modify the PROTOCOL.INI file and remove the
   semi-colon in front of [EX10_NIF] and change the IOAddress of the
   adapter to match the setting in EX10Set.

10 Add the lines to your CONFIG.SYS file as indicated above.

11 Reboot and run BAN to attach to the Banyan server.


Hints and Tips
--------------

1  Error Message with PRO0025E

   This type of message will occur when the driver attempts to bind to
   the protocol manager.  It generally indicates a syntax or other error
   in the PROTOCOL.INI file.  Review the file carefully for errors.
   Also, verify parameters entered in PCCONFIG.  For additional
   information, reference NDISBAN.DOC, which is part of the NDIS Banyan
   client software.

2  Make sure your NDISBAN.COM is dated April 1994 or later.  Earlier
   versions may not work properly.

3  General parameters for the PROTOCOL.INI file are listed below.  For
   advanced options, see the document on NDIS Driver Notes.
   
   DRIVERNAME: (required) If you have a single adapter, use the syntax in
      the example above.  If you are installing multiple adapters, each
      adapter must have a unique driver name.  Additional instances of
      the driver would be referenced by DRIVERNAME=EX10x$, where "x"
      would be a unique number 2 through 9.
   
   IOADDRESS: (optional for single adapter systems - except when set to
      certain addresses noted below) This value must match the adapter's
      I/O address.  If the driver does not find the adapter at the
      specified I/O address, it will scan most of the I/O addresses that
      the adapter could be at and will load if it finds the adapter.  The
      only addresses the driver doesn't scan are 2E0, 2F0 or 370. If you
      have used one of these address, this parameter isn't optional. If
      you use multiple adapters in one machine, make sure you specify the
      correct IOADDRESS for each board.  Otherwise, the driver will fail
      when loading on the second card.

*  Third-party trademarks are the property of their respective owners.