TPE cabling specifications
v1.00
Specifications and Recommendations for Twisted-Pair Ethernet cable
==================================================================
The EtherExpress(TM) 10 ISA adapters have a small, snap-in RJ45
connector.
RJ45 cabling is also known as twisted-pair Ethernet (TPE), unshielded
twisted pair (UTP) and 10BASE-T.
This document covers the following topics:
- Recommended cables
- Cable and connector pinouts
- Connecting two workstations without a hub
- Link integrity
- Common problems
For more information on the 10BASE-T specification, contact your local
network supplier or call the IEEE (800-678-IEEE).
Recommended cables
------------------
The RJ45 connector can use 22, 24, or 26-gauge UTP cabling. The cable
must comply with the IEEE 802.3 10BASE-T standard.
If you're using TPE cabling in a residential environment, you must use a
shielded cable.
The cable between the computer and the hub must be less than 100 meters
long.
These UTP cables work well:
------------------------------------------------------
Manufacturer Model number No. of pairs
------------------------------------------------------
Belden 9562 2
------------------------------------------------------
Data Set 2402 4
------------------------------------------------------
Belden 9566 6
------------------------------------------------------
Silver satin is not within the 10BASE-T specification and cannot be used.
If used, it may not work at all, or may give intermittent results.
EtherExpress adapters do not support pre10BASE-T concentrators.
Cable and connector pinouts
---------------------------
If you need to repair a cable or provide connectors for UTP cable, wire
straight through as shown in the following table.
Use only four of the eight pins. Pins 1 and 2 must be a pair, and pins 3
and 6 must be a pair.
Function Pin# Pin#
-------------------------------------
TX+ 1 <--------> 1
TX- 2 <--------> 2
RX+ 3 <--------> 3
RX- 6 <--------> 6
-------------------------------------
To allow for a straight-through cable, the hub provides an internal
transmit/receive crossover function. This means the transmit circuit of
the network card is connected to the receive circuit of the hub and vice
versa.
Pinout for the RJ45 connector
-----------------------------
---------- --------------------------
1 |-- | 8 |------------ |
2 |-- | 7 |------------ |
3 |-- --- 6 |------------ |
4 |-- | 5 |------------ |
5 |-- | 4 |------------ |
6 |-- --- 3 |------------ |
7 |-- | 2 |------------ |
8 |-- | 1 |------------ |
---------- --------------------------
END TOP
Pin name and function:
1. Transmit Data Plus. The positive signal for the TD differential
pair. This signal contains the serial output data stream
transmitted onto the network.
2. Transmit Data Minus. The negative signal for the TD differential
pair. This contains the same output as pin 1.
3. Receive Data Plus. The positive signal for the RD differential
pair. This signal contains the serial input data stream received
from the network.
4. not connected
5. not connected
6. Receive data minus. The negative signal for the RD differential
pair. This signal contains the same input as pin 3.
7. not connected
8. not connected
Connecting two workstations without a hub
-----------------------------------------
10BASE-T uses a star topology. This means there is a hub or concentrator
in the center of a star and each workstation or server is connected to
this hub.
For TEST purposes, you can directly connect two workstations or a
workstation and a server without using a hub. This requires a special
cable that incorporates the crossover function.
Function Pin# Pin# Function
----------------------------------------------
TX+ 1 <--------> 3 RX+
TX- 2 <--------> 6 RX-
RX+ 3 <--------> 1 TX+
RX- 6 <--------> 2 TX-
----------------------------------------------
NOTE: This is not an IEEE supported configuration and should be
used for test purposes only.
Link integrity
--------------
For 10BASE-T networks, Link Integrity (LI) needs to be on. Some
transceivers, Ethernet cards, or other network devices allow you to turn
it off, but Link Integrity is always on with the EtherExpress adapters.
If you're using a transceiver to go to a thick/thin Ethernet segment,
Link Integrity must be set to on for the transceiver.
Common problems
---------------
A hub can't "see" a workstation
-------------------------------
This is often caused by a crossed wire in the cable or wiring closet.
Check to make sure the wiring is correct.
Workstations can't connect to the network
-----------------------------------------
If your workstations are having problems connecting, reset or power
off/on your concentrator or hub.
Polarity problems
-----------------
A common problem in 10BASE-T wiring is crossing the positive and negative
phases of the transmit or receive signals. For example, a problem would
occur if pins 1 and 2 were crossed. (TX+ connected to TX-).
The current EtherExpress adapters automatically detect this problem and
adjust for it internally. Early EtherExpress 16TP adapters did not have
this feature.
Even though the current EtherExpress adapters can take care of this
crossover for you, it is best to check your wiring and correct this
problem if you find it.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.