Nw311.txt Driver File Contents (v23.zip)

**
**
**                                                                           
**  VIA Networking Velocity Family Gigabit Ethernet Adapter
**                                                                           
**  ODI Driver for NetWare 3.11 Servers           
**                                                                           
**  v2.01    Oct, 2004
**
**

Introduction:
=============

  The Gigabit Ethernet Adapter Driver for NetWare 3.11 Servers confirms to the
  Novell Open Data-Link Interface (ODI) specification. This  document shows you
  how to setup the driver and how to use the enhanced functions by setting the 
  custom keywords.


Contents of the Subdirectory:
=============================

    NW311.TXT           This file.
    GETNWSA.LAN         The ODI driver for NetWare 3.11 Server.
    ETHERTSM.NLM        Patch file for Netware 3.11 Server.
    LSLENH.NLM          Patch file for Netware 3.11 Server.
    MONITOR.NLM         Patch file for Netware 3.11 Server.
    MSM31X.NLM          Patch file for Netware 3.11 Server.
    PATCHMAN.NLM        Patch file for Netware 3.11 Server.


Installation:
=============

  Before starting with the installation process, make sure that the adapter
  is properly installed and configured. You can use the diagnostic program
  (A:\SETUP.EXE) in DOS mode to make sure your connection with the network is
  correct.

  Using Server Install utility:
  -----------------------------
    1) On the server console, execute the INSTALL.NLM program:

                LOAD INSTALL <Enter>

    2) Choose "Driver Option/System Options".

    3) You can add the LOAD and BIND command lines to the AUTOEXEC.NCF file so
       that the LAN driver will be loaded automatically while the server
       is starting up. You should load LSLENH.NLM first before you load driver.


  Loading Driver Manually:
  ------------------------
    1) On the server console, load LSLENH.NLM first, for example:

          LOAD A:\NETWARE\NWSERVER.311\LSLENH

    2) On the server console, load the driver directly, for example:

          LOAD A:\NETWARE\NWSERVER.311\GETNWSA.LAN FRAME=Ethernet_802.2 name=tt

    3) Bind with IPX:

          BIND IPX tt

    4) You can login the server from a workstation, and then copy GETNWSA.LAN to
       the directory SYS:\SYSTEM on server. Add the LOAD and BIND command lines
       to AUTOEXEC.NCF file so that the lan driver will be loaded automatically
       while the server starting up next time.


  NOTE:
  -----
    1) Multiple Lan Adapters in a system:
        If you want to install mutiple lan adapters in a server, you have to use
        the keyword, SLOT, to let driver locate the right adapter.
        For example:

        LOAD GETNWSA.LAN SLOT=10 FRAME=Ethernet_802.2 NAME=Lan_1
        BIND IPX TO Lan_1 NET=2001
        LOAD GETNWSA.LAN SLOT=11 FRAME=Ethernet_802.2 NAME=Lan_2
        BIND IPX TO Lan_2 NET=2002

        And the server's packet receive buffers probably need to be increased.
        To do this, setting the following command to STARTUP.NCF file.

            SET MINIMUM PACKET RECEIVE BUFFERS=500  (Or higher)

    2) Tagging ability :
        If keyword "TAG" is supported, the transmited packets
        will be tagged packets. It's only supportted by management adapter.

    3) VLAN support :
        For now, we only support one VID value setting. It's only supportted by 
        management adapter.

    4) Flow Control ability:
        "Hardware Default (Auto)" means the flow control ability depends on the
        auto-negotiation result with the link partner.
        In other settings ("Enable Tx", "Enable Rx", "Enable Tx/Rx"), driver will
        set the Tx or Rx flow control ability without auto-negotiation.

    5) If the receive buffers are not enough for flow control ability using,
       driver will disable flow control automatically.


Configuration Parameters:
=========================

    Custom Keywords:
    ----------------
    
        CONNECTIONTYPE                  This keyword is used to specify media type.
        
            CONNECTIONTYPE=AutoSense
            CONNECTIONTYPE=10BASET
            CONNECTIONTYPE=10BASETFD
            CONNECTIONTYPE=100BASETX
            CONNECTIONTYPE=100BASETXFD
            
        FLOW_CONTROL                    This keyword is used to specify flow control
                                        ability.
            FLOW_CONTROL=DISABLE
            FLOW_CONTROL=ENABLE
            FLOW_CONTROL=TX
            FLOW_CONTROL=RX
            FLOW_CONTROL=HARDWARE_DEFAULT   (default)
            
        TAG                             This keyword is used to enable TX tagging.
                                        It's combined with VID keyword for transmitting
                                        tagged packet. Only be supported by management 
                                        adapter.
            TAG=ENABLE
            TAG=DISABLE                 (default)
            
        VID                             This keyword is used to support VLAN's VID.
                                        It's only worked when TAG keyword is enabled.
                                        Only be supported by management adapter.
        
            VID=1~4094


Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web4, load: 1.50