;****************************************************************************
;
; OEMSETNT.INF
;
; 3Com Megahertz 10/100 LAN + 56K Modem PC Card Windows NT Setup File
;
; Copyright 1998 3Com Corporation
;
;****************************************************************************
;
; Revision History
;
; %ver 1.0f
;
; BFC 07/23/97 1.0a Initial Release for Rev.B EtherDisk
; BFC 08/13/97 1.0b Release for Rev.C EtherDisk
; TES 10/16/97 1.0c Release for FEM556
; BFC 01/19/97 1.0d Release for FEM556
; BFC 01/23/97 1.0e Release for FEM556
; BFC 01/26/97 1.0f Release for FEM556
;****************************************************************************
[Identification]
OptionType = NetAdapter
[PlatformsSupported]
ISA
; EISA
; MCA
; PCI
PCMCIA
"Jazz-Internal Bus"
[Options]
FEM556
[OptionsTextENG]
FEM556 = "3Com Megahertz 10/100 LAN + 56K Modem PC Card (Ethernet)"
[AllFileConstants]
GenericInfVersion = " v1.00"
UtilityInf = "UTILITY.INF"
ParamInf = "NCPARAM.INF"
subroutineinf = "SUBROUTN.INF"
SoftwareType = "driver"
Exit_Code = 0
NetEventDLL = "%SystemRoot%\System32\netevent.dll"
IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll"
TrayIconExe = "comsmd.exe -try"
UninstallExe = "un3c556"
UnInstallName = "3Com PC Card Diagnostics Utilities"
Manufacturer = "3Com"
[FileConstants-FEM556]
GenericAdapterName = "3Com Megahertz 10/100 LAN + 56K Modem PC Card (Ethernet)"
GenericDriverName = "3Com Megahertz 10/100 LAN + 56K Modem PC Card (Ethernet)"
GenericName = "FEM556"
ProductMajorVersion = "3"
ProductMinorVersion = "51"
ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion)
ProductSoftwareName = "FEM556"
ProductSoftwareDescription = "3Com Megahertz 10/100 LAN + 56K Modem PC Card (Ethernet)"
NetRuleSoftwareType = "FEM556Sys ndisDriver FEM556Driver"
NetRuleSoftwareUse = $(SoftwareType)
NetRuleSoftwareBindForm = """FEM556Sys"" yes no container"
NetRuleSoftwareClass = {"FEM556Driver basic"}
NetRuleSoftwareBindable = {"FEM556Driver FEM556Adapter non exclusive 100"}
ProductHardwareName = "FEM556"
ProductHardwareDescription = "3Com Megahertz 10/100 LAN + 56K Modem PC Card (Ethernet)"
NetRuleHardwareType = "FEM556 FEM556Adapter"
NetRuleHardwareBindForm = " yes yes container"
NetRuleHardwareClass = {"FEM556Adapter basic"}
ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion"
ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters"
VERS1Manufacturer = "3Com"
VERS1Product = "TX Fast EtherLink PC Card"
VERS1Type = "FEM556-FastEtherLink"
PCMCIA = 1
[GeneralConstants]
from = ""
to = ""
ExitCodeOk = 0
ExitCodeCancel = 1
ExitCodeFatal = 2
KeyNull = ""
MAXIMUM_ALLOWED = 33554432
RegistryErrorIndex = NO_ERROR
KeyProduct = ""
KeyParameters = ""
TRUE = 1
FALSE = 0
NoTitle = 0
ExitState = "Active"
OldVersionExisted = $(FALSE)
DriverPath = $(!STF_NTPATH)\drivers
NT350VersionConstant = "3.50"
NT310VersionConstant = "3.10"
NT400VersionConstant = "(4.0)"
[date]
Now = {} ? $(!LIBHANDLE) GetSystemDate
[Identify]
read-syms Identification
set Status = STATUS_SUCCESSFUL
set Identifier = $(OptionType)
set Media = #("Source Media Descriptions", 1, 1)
Return $(Status) $(Identifier) $(Media)
[ReturnOptions]
set Status = STATUS_FAILED
set OptionList = {}
set OptionTextList = {}
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) in $(LanguageList)
ifstr(i) $($1) == ""
goto returnoptions
endif
set PlatformList = ^(PlatformsSupported, 1)
Ifcontains(i) $($1) in $(PlatformList)
goto returnoptions
else
set Status = STATUS_NOTSUPPORTED
goto finish_ReturnOptions
endif
else
set Status = STATUS_NOLANGUAGE
goto finish_ReturnOptions
endif
returnoptions = +
set OptionList = ^(Options, 1)
set OptionTextList = ^(OptionsText$($0), 1)
set Status = STATUS_SUCCESSFUL
finish_ReturnOptions = +
Return $(Status) $(OptionList) $(OptionTextList)
[InstallOption]
set Status = STATUS_FAILED
set Option = $($1)
set SrcDir = $($2)
set AddCopy = $($3)
set DoCopy = $($4)
set DoConfig = $($5)
Set !DebugOutputControl = 0
; Vivek
set ComPortPrefix = Serial3Com
; Vivek
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) NOT-IN $(LanguageList)
Return STATUS_NOLANGUAGE
endif
set-subst LF = "\n"
read-syms GeneralConstants
read-syms AllFileConstants
read-syms FileConstants"-"$(Option)
read-syms DialogConstants$(!STF_LANGUAGE)"-"$(Option)
ifstr(i) $(!NTN_Origination) == "NCPA"
set Continue = $(OK)
endif
read-syms AllFileConstants$(!STF_LANGUAGE)
read-syms FileConstants$(!STF_LANGUAGE)"-"$(Option)
detect date
set-title $(FunctionTitle)
set to = Begin
set from = Begin
; -------------------------- BEGIN FORCE FIX
; Update the modem info by reading from the ZZZx
; entries under the Serial\Parameters in registry
Debug-Output "<DBG: FORCE> Starting ModemIOBaseAddressList = "$(ModemIOBaseAddressList)
Debug-Output "<DBG: FORCE> Starting ModemIOBaseAddressValues = "$(ModemIOBaseAddressValues)
set SerParams = "SYSTEM\CurrentControlSet\Services\Serial\Parameters"
set ZZZComPort = $(SerParams)"\ZZZa"
install "install-update-modem-info"
set ZZZComPort = $(SerParams)"\ZZZb"
install "install-update-modem-info"
set ZZZComPort = $(SerParams)"\ZZZc"
install "install-update-modem-info"
set ZZZComPort = $(SerParams)"\ZZZd"
install "install-update-modem-info"
Debug-Output "<DBG: FORCE> Final ModemIOBaseAddressList = "$(ModemIOBaseAddressList)
Debug-Output "<DBG: FORCE> Final ModemIOBaseAddressValues = "$(ModemIOBaseAddressValues)
Debug-Output "<DBG: FORCE> Final ModemIrqList = "$(ModemIrqList)
Debug-Output "<DBG: FORCE> Final ModemIrqValues = "$(ModemIrqValues)
;-------------------------- END FORCE FIX
set CommonStatus = STATUS_SUCCESSFUL
EndWait
Begin = +
set CurrentVersionValue = ""
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows Nt\CurrentVersion" $(!REG_KEY_READ) KeyNt
Ifstr(i) $(KeyNt) != ""
GetRegValue $(KeyNt) "CurrentVersion" CurrentVersionValue
Debug-Output "$(InfFile) $(Option): WinNT CurrentVersion ="$(CurrentVersionValue)
CloseRegKey $(KeyNt)
Endif
ifstr(i) (*($(CurrentVersionValue),4)) == $(NT400VersionConstant)
set NDIS_VER = NDIS4
set ProductSoftwareImagePath = "\SystemRoot\System32\drivers\FEM556N4.SYS"
else
set NDIS_VER = NDIS3
set ProductSoftwareImagePath = "\SystemRoot\System32\drivers\FEM556N3.SYS"
endif
ifstr(i) (*($(CurrentVersionValue),4)) == $(NT310VersionConstant)
Debug-Output "$(InfFile) $(Option): Configureadapter"
set Error = "Windows NT v3.10 is not support by this product"
goto fatal
endif
Set ActivateDetection = FALSE
Ifstr(i) $(!NTN_InstallMode) == deinstall
set StartLabel = removeadapter
else-Ifstr(i) $(!NTN_InstallMode) == Update
set StartLabel = UpgradeSoftware
else-Ifstr(i) $(!NTN_InstallMode) == bind
set StartLabel = bindingadapter
else-Ifstr(i) $(!NTN_InstallMode) == configure
set StartLabel = configureadapter
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error: cannot get an error string."
goto ShellCodeError
endif
set Error = $($R0)
set from = end
set to = end
goto nonfatalinfo
endif
else
set StartLabel = installadapter
set OEM_ABANDON_OPTIONS = {}
set OEM_ABANDON_SOFTWARE = FALSE
set OEM_ABANDON_ON = TRUE
endif
;Vivek
set IRQValue = *($(IRQList), 1)
;set IRQValue = *($(IRQList), 5)
;Vivek
set IOBaseAddrValue = *($(IOBaseAddrList), 1)
;Vivek
set MemoryAddrValue = *($(MemoryAddrList), 1) ; Memory Address = 0xD0000
;set MemoryAddrValue = *($(MemoryAddrList), 9) ; Memory Address = 0xD0000
;Vivek
set ComPortValue = *($(ComPortList), 2) ; COM2
set Static1Label = "Note: Modem and Network use same interrupt"
Set from = $(fatal)
Set to = $(fatal)
Goto $(StartLabel)
installadapter = +
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
CloseRegKey $(KeyProduct)
ifstr(i) !(NTN_RegBase) == $(ProductKeyName)
Shell $(UtilityInf), VerExistedDlg, $(ProductSoftwareTitle),+
$(ProductVersion)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error: cannot get an error string."
goto ShellCodeError
endif
goto end
else
Shell $(UtilityInf), CardExistedDlg
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error: cannot get an error string."
goto ShellCodeError
endif
ifstr(i) $($R1) != "OK"
goto end
endif
set OldVersionExisted = $(TRUE)
endif
endif
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) NO
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
Set FileToCheck = $($R1)\OEMSETNT.INF
LibraryProcedure FilePresent,$(!LIBHANDLE), CheckFileExistance $(FileToCheck)
Ifstr(i) $(FilePresent) != "YES"
Goto installadapter
Endif
Set SrcDir = $($R1)
install "Install-Dll"
Debug-Output "Install-3nicdiag"
install "Install-3nicdiag"
StartWait
ifstr(i) (*($(CurrentVersionValue),4)) == $(NT400VersionConstant)
Debug-Output "$(InfFile) $(Option): Windows NT 4.00"
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows\CurrentVersion\Run" $(!REG_KEY_ALL_ACCESS) KeyNt
set TrayIconList = {COMSMDEXE,$(NoTitle),$(!REG_VT_SZ),$(TrayIconExe)}
SetRegValue $(KeyNt) $(TrayIconList)
Debug-Output "Install-TraynCpl"
install "Install-TrayAndCpl"
CloseRegKey $(KeyNt)
RunProgram ExitCode "Windows Directory" "" COMSMD.EXE "-setup"
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall" $(!REG_KEY_ALL_ACCESS) KeyNt
ifstr $(KeyNt) == ""
CreateRegKey $(!REG_H_LOCAL) {"SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall" , 0, GenericClass} "" $(!REG_KEY_ALL_ACCESS) "" KeyNt
endif
OpenRegKey $(KeyNt) "" "3ComNicUnInstall" $(!REG_KEY_ALL_ACCESS) KeyNt2
ifstr $(KeyNt2) == ""
CreateRegKey $(KeyNt) {"3ComNicUnInstall" , 0, GenericClass} "" $(!REG_KEY_ALL_ACCESS) "" KeyNt2
endif
set NewValueList = {{DisplayName, $(NoTitle), $(!REG_VT_SZ), "3Com PC Card Diagnostics"},+
{UninstallString, $(NoTitle), $(!REG_VT_SZ), "UN3C556.EXE"}}
Shell $(UtilityInf), AddValueList, $(KeyNt2), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
CloseRegKey $(KeyNt)
CloseRegKey $(KeyNt2)
endif
EndWait
goto adaptersetup
configureadapter = +
Ifstr $(KeyProduct) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) == $(KeyNull)
set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
Debug-Output "Cannot find component product key"
goto fatalregistry
Endif
Endif
Debug-Output "INF: Shelling to FindService"
Shell $(UtilityInf) FindService, $(KeyProduct)
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "INF: FindService shell failure"
Goto ShellCodeError
Endif
Ifstr(i) $($R0) != NO_ERROR
Debug-Output "INF: FindService Shell error: "$($R0)
Goto fatalregistry
endif
Set KeyParameters = $($R2)
CloseRegKey $($R1)
Ifstr $(KeyParameters) == $(KeyNull)
set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
Debug-Output "Cannot find component service"
goto fatalregistry
endif
set OldVersionExisted = $(TRUE)
set ValueName = ""
set ValueData = ""
set ValueStr = ""
set ValueList = {}
EnumRegValue $(KeyParameters) ValueList
ForListDo $(ValueList)
set ValueItem = $($)
set ValueName = *($(ValueItem),1)
set ValueData = *($(ValueItem),4)
ifstr(i) $(ValueName) == "IoBaseAddress_1"
set IOBaseAddrIndex = $(ValueData)
else-ifstr(i) $(ValueName) == "InterruptNumber"
set IRQValueIndex = $(ValueData)
else-ifstr(i) $(ValueName) == "PCCARDAttributeMemoryAddress"
set MemoryAddrIndex = $(ValueData)
else-ifstr(i) $(ValueName) == "ComPort"
set ComPortIndex = $(ValueData)
;Vivek
else-ifstr(i) $(ValueName) == "AdapterName"
Debug-Output "<DBG> AdapterName in registry = "$(ValueData)
set OldAdapterName = $(ValueData)
;Vivek
endif
EndForListDo
set IRQValue = *($(IRQList), ~($(IRQValues),$(IRQValueIndex)))
ifstr(i) $(IRQValue) == ""
set IRQValue = *($(IRQList), 5)
endif
set IOBaseAddrValue = *($(IOBaseAddrList), ~($(IOBaseAddrValues),$(IOBaseAddrIndex)))
ifstr(i) $(IOBaseAddrValue) == ""
set IOBaseAddrValue = *($(IOBaseAddrList), 1)
endif
set MemoryAddrValue = *($(MemoryAddrList), ~($(MemoryAddrValues),$(MemoryAddrIndex)))
ifstr(i) $(MemoryAddrValue) == ""
set MemoryAddrValue = *($(MemoryAddrValues), 2)
endif
set ComPortValue = *($(ComPortList), ~($(ComPortValues),$(ComPortIndex)))
ifstr(i) $(ComPortValue) == ""
set ComPortValue = *($(ComPortValues), 2)
endif
adaptersetup = +
LoadLibrary "disk 1" $(DialogDllName) hLib
read-syms FileDependentDlg$(!STF_LANGUAGE)"-"$(Option)
set ENABLER = 0
ui start "InputDlg" $(hLib)
set ExitButton = $(ButtonPressed)
FreeLibrary $(hLib)
ifstr(i) $(DLGEVENT) == "CONTINUE"
set IOBaseAddrIndex = $(Combo1Out)
set IRQValueIndex = $(Combo2Out)
set MemoryAddrIndex = $(Combo3Out)
set ComPortIndex = $(Combo4Out)
set ModemInterruptNumberIndex = $(Combo5Out)
set ExitButton = $(ButtonPressed)
ui pop 1
else-ifstr(i) $(DLGEVENT) == "EXIT"
set CommonStatus = STATUS_USERCANCEL
ui pop 1
goto end
else
set CommonStatus = STATUS_USERCANCEL
ui pop 1
Debug-Output "Action: unknown. Bye."
goto end
endif
skipoptions =+
ifint $(OldVersionExisted) == $(TRUE)
ifstr(i) $(!NTN_InstallMode) == configure
goto writeparameters
endif
endif
StartWait
ifint $(OldVersionExisted) == $(FALSE)
ifstr(i) $(!NTN_InstallMode) == "install"
Ifstr(i) $(DoCopy) == "YES"
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
Set SrcDir = $($R1)
Endif
install "Install-Option"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
endif
endif
Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), +
$(ProductSoftwareName), +
$(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), +
$(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+
$(NetEventDLL)
Set OEM_ABANDON_SOFTWARE = TRUE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
set KeyProduct = $($R1)
Set SoftNetRulesKey = $($R2)
CloseRegKey $($R3)
CloseRegKey $($R4)
CloseRegKey $($R5)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Registry error: add software components"
CloseRegKey $(KeyProduct)
CloseRegKey $(SoftNetRulesKey)
goto fatalregistry
endif
;Vivek
ifstr $(AdapterNumber) == ""
Debug-Output "<DBG> AdpaterNumber unknown !"
Debug-Output "<DBG> NTN_RegBase = "$(!NTN_RegBase)
set MyAdapterName = $(!NTN_RegBase)
Debug-Output "<DBG> MyAdapterName = "$(MyAdapterName)
Split-String $(MyAdapterName), "\", MyCardInfo
Debug-Output "<DBG> MyCardInfo = "$(MyCardInfo)
set AdapterNumber = *($(MyCardInfo),11)
Debug-Output "<DBG> AdapterNumber = "$(AdapterNumber)
endif
;Vivek
set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+
{MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+
{MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+
{Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(KeyProduct), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Registry error: add value list."
CloseRegKey $(KeyProduct)
CloseRegKey $(SoftNetRulesKey)
goto fatalregistry
endif
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+
{use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, +
{bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, +
{bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareBindable)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(SoftNetRulesKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
CloseRegKey $(KeyProduct)
CloseRegKey $(SoftNetRulesKey)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Resgitry error: add value list."
goto fatalregistry
endif
endif
Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)
ifint $($R4) != -1
Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
endif
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "Cannot add hardware component"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Registry error: add hardware component"
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
goto fatalregistry
endif
set KeyParameters = $($R3)
set KeyAdapterRules = $($R2)
set AdapterNumber = $($R4)
set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+
{Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardwareTitle)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareDescription)},+
{ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $($R1), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
CloseRegKey $($R1)
set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardwareType)},+
{bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardwareClass)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(KeyAdapterRules), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
EndWait
Debug-Output "Resgitry error: add value list."
CloseRegKey $(KeyParameters)
CloseRegKey $(KeyAdapterRules)
goto fatalregistry
endif
CloseRegKey $(KeyAdapterRules)
goto writeparameters
writeparameters = +
set BusTypeNum = 1
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
Debug-Output "$(InfFile) $(Option): Write Pcmcia database"
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Pcmcia\DataBase\3Com\Megahertz 3CCFEM556" $(MAXIMUM_ALLOWED) MyPcmciaHandle
Debug-Output "CreatRegKey (FEM556)"
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Pcmcia\DataBase\3Com" $(MAXIMUM_ALLOWED) MyPcmciaHandle
Ifstr $(MyPcmciaHandle) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Pcmcia\DataBase" $(MAXIMUM_ALLOWED) MyPcmciaKey
CreateRegKey $(MyPcmciaKey) {"3Com",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" MyPcmcialHandle
CloseRegKey ($MyPcmciaKey)
endif
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Pcmcia\DataBase\3Com" $(MAXIMUM_ALLOWED) MyPcmciaKey
CreateRegKey $(MyPcmciaKey) {"Megahertz 3CCFEM556",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" MyPcmcialHandle
CloseRegKey ($MyPcmciaKey)
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Pcmcia\DataBase\3Com\Megahertz 3CCFEM556" $(MAXIMUM_ALLOWED) MyPcmciaHandle
endif
set NewValueList = {{Driver,$(NoTitle),$(!REG_VT_SZ),"FEM556"},+
{DeviceType,$(NoTitle),$(!REG_VT_SZ),"NET"}}
Shell $(UtilityInf), AddValueList, $(MyPcmciaHandle), $(NewValueList)
Debug-Output "<DBG> AddValueList - Driver:REG_SZ:FEM556"
CloseRegKey $(MyPcmciaHandle)
set IRQValue = *($(IRQValues), ~($(IRQList), $(IRQValueIndex)))
set IOBaseAddrValue = *($(IOBaseAddrValues),~($(IOBaseAddrList), $(IOBaseAddrIndex)))
set ComPortValue = *($(ComPortValues), ~($(ComPortList), $(ComPortIndex)))
Debug-Output "<DBG> Install/ComPortIndex "$(ComPortIndex)
; Vivek
; check if user selected Auto for Interrupt - if so
; we should write the correct irq for the modem intr
; and write 0 for the network intr.
;
set ModemInterruptNumberValue = *($(IRQValues), ~($(IRQList), $(IRQValueIndex)))
Debug-Output "<DBG> Install/ModemInterruptNumberValue "$(ModemInterruptNumberValue)
ifint $(ModemInterruptNumberValue) == 0
Debug-Output "<DBG> Install/ModemInterruptNumberValue is 0 !"
Debug-Output "<DBG> Install/ModemIRQValues "$(ModemIrqValues)
Debug-Output "<DBG> Install/ComPortList "$(ComPortList)
Debug-Output "<DBG> Install/ComPortIndex "$(ComPortIndex)
set ModemInterruptNumberValue = *($(ModemIrqValues), ~($(ComPortList),$(ComPortIndex)))
Debug-Output "<DBG> Install/ModemInterruptNumberValue "$(ModemInterruptNumberValue)
endif
; Vivek
set ModemIOBaseAddressValue = *($(ModemIOBaseAddressValues), $(ComPortValue))
set MemoryAddrValue = *($(MemoryAddrValues), ~($(MemoryAddrList), $(MemoryAddrIndex)))
;Vivek
;set-add CommonMemoryAddrValue = $(MemoryAddrValue), 8192
ifint $(MemoryAddrValue) != 0
set-add CommonMemoryAddrValue = $(MemoryAddrValue), 8192
else
set CommonMemoryAddrValue = 0
endif
ifstr $(OldAdapterName) == ""
set OldAdapterName = $(ProductHardwareName)$(AdapterNumber)
Debug-Output "<DBG> setting OldAdapterName"
endif
Debug-Output "<DBG> OldAdapterName = "$(OldAdapterName)
;Vivek
set NewValueList = {{IoBaseAddress, $(NoTitle),$(!REG_VT_DWORD),$(ModemIOBaseAddressValue)},+
;Vivek
; The network interrupt should match modem interrupt in case of Auto
; {InterruptNumber, $(NoTitle),$(!REG_VT_DWORD),$(IRQValue)},+
{InterruptNumber, $(NoTitle),$(!REG_VT_DWORD),0},+
;Vivek
{MediaType, $(NoTitle),$(!REG_VT_DWORD),1},+
{BusType, $(NoTitle),$(!REG_VT_DWORD),$(BusTypeNum)},+
{BusNumber, $(NoTitle),$(!REG_VT_DWORD),0},+
{CardType,$(NoTitle),$(!REG_VT_DWORD),0},+
{AdapterType, $(NoTitle),$(!REG_VT_DWORD),259},+
{OSType, $(NoTitle),$(!REG_VT_DWORD),1},+
;Vivek
{SoftexPcmcia, $(NoTitle),$(!REG_VT_DWORD),1},+
{AdapterName,$(NoTitle),$(!REG_VT_SZ),$(OldAdapterName)},+
;{Pcmcia, $(NoTitle),$(!REG_VT_DWORD),1},+
;Vivek
{LANOnly, $(NoTitle),$(!REG_VT_DWORD),0},+
{PCCARDAttributeMemoryAddress, $(NoTitle),$(!REG_VT_DWORD),$(MemoryAddrValue)},+
{PCCARDAttributeMemorySize, $(NoTitle),$(!REG_VT_DWORD),8192},+
{IOBaseAddress_1, $(NoTitle),$(!REG_VT_DWORD),$(IOBaseAddrValue)},+
{ModemFunction, $(NoTitle), $(!REG_VT_DWORD),1},+
{ComPort, $(NoTitle),$(!REG_VT_DWORD),$(ComPortValue)},+
;Vivek
; {ModemInterruptNumber, $(NoTitle),$(!REG_VT_DWORD),$(IRQValue)},+
{ModemInterruptNumber, $(NoTitle),$(!REG_VT_DWORD),$(ModemInterruptNumberValue)},+
;Vivek
{IoLength, $(NoTitle),$(!REG_VT_DWORD), 7},+
{IoLength_1, $(NoTitle),$(!REG_VT_DWORD), 31},+
{MemoryMappedBaseAddress, $(NoTitle),$(!REG_VT_DWORD),$(CommonMemoryAddrValue)},+
{MemoryMappedSize, $(NoTitle),$(!REG_VT_DWORD),8192},+
}
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
CloseRegKey $(KeyParameters)
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial" $(MAXIMUM_ALLOWED) MyNewSerialHandle
;
; If we are on WinNt 3.51 then replace serial with serial3.sys driver
;
ifstr(i) (*($(CurrentVersionValue),4)) == $(NT400VersionConstant)
Set NewValueList = { {PermitShare, $(NoTitle),$(!REG_VT_DWORD),1},+
{ShareInterrupt,$(NoTitle),$(!REG_VT_DWORD),1}}
;Vivek
; {ImagePath,$(NoTitle),$(!REG_VT_SZ),"\SystemRoot\System32\drivers\serial.sys"}}
;Vivek
else
Set NewValueList = { {PermitShare, $(NoTitle),$(!REG_VT_DWORD),1},+
{ShareInterrupt,$(NoTitle),$(!REG_VT_DWORD),1}}
;Vivek
; {ImagePath,$(NoTitle),$(!REG_VT_SZ),"\SystemRoot\System32\drivers\serial3.sys"}}
;Vivek
endif
Shell $(UtilityInf), AddValueList, $(MyNewSerialHandle), $(NewValueList)
CloseRegKey $(MyNewSerialHandle)
;Vivek
;***************************************************************
Debug-Output "<DBG> Checking if COM port needs to be added ...."
;***************************************************************
ifstr $(AdapterNumber) == ""
Debug-Output "<DBG> AdpaterNumber unknown !"
Debug-Output "<DBG> NTN_RegBase = "$(!NTN_RegBase)
set MyAdapterName = $(!NTN_RegBase)
Debug-Output "<DBG> MyAdapterName = "$(MyAdapterName)
Split-String $(MyAdapterName), "\", MyCardInfo
Debug-Output "<DBG> MyCardInfo = "$(MyCardInfo)
set AdapterNumber = *($(MyCardInfo),11)
Debug-Output "<DBG> AdapterNumber = "$(AdapterNumber)
endif
set ComPortName = $(ComPortPrefix)$(AdapterNumber)
Debug-Output "<DBG> ComPortName = "$(ComPortName)
Debug-Output "<DBG> Deleting old "$(ComPortName)
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) MyNewSerialHandle
DeleteRegTree $(MyNewSerialHandle) $(ComPortName)
CloseRegKey $(MyNewSerialHandle)
Debug-Output "<DBG> Adding the COM port "$(ComPortName)
; OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters\Serial3Com" $(MAXIMUM_ALLOWED) MyNewSerialHandle
; Ifstr $(MyNewSerialHandle) == $(KeyNull)
;Vivek
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) SerialKey
;Vivek
CreateRegKey $(SerialKey) {$(ComPortName),0,GenericClass} "" $(MAXIMUM_ALLOWED) "" MyNewSerialHandle
; CreateRegKey $(SerialKey) {"Serial3Com",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" MyNewSerialHandle
;Vivek
CloseRegKey $(SerialKey)
;Vivek
; Endif
;Vivek
;Vivek
Debug-Output "<DBG> ComPortIndex "$(ComPortIndex)
Debug-Output "<DBG> ModemInterruptNumberValue "$(ModemInterruptNumberValue)
ifint $(ModemInterruptNumberValue) == 0
Debug-Output "<DBG> ModemInterruptNumberValue is 0 !"
set ModemInterruptNumberValue = *($(ModemIrqValues), ~($(ComPortList),$(ComPortIndex)))
Debug-Output "<DBG> ModemInterruptNumberValue "$(ModemInterruptNumberValue)
endif
;Vivek
Set NewValueList = {{DosDevices, $(NoTitle),$(!REG_VT_SZ), "COM"$(ComPortValue)},+ ; "COMx"
{ForceFifoEnable, $(NoTitle),$(!REG_VT_DWORD), 1},+ ; Always true
;Vivek
{ExternallyConfiguredModem, $(NoTitle), $(!REG_VT_DWORD), 1},+
;Vivek
; {Interrupt, $(NoTitle),$(!REG_VT_DWORD), $(IRQValue)},+ ; Interrupt for MHZ modem
;Vivek
{Interrupt, $(NoTitle), $(!REG_VT_DWORD), $(ModemInterruptNumberValue)},+
;Vivek
{InterruptMode,$(NoTitle),$(!REG_VT_DWORD),0},+
{PortAddress, $(NoTitle),$(!REG_VT_DWORD), $(ModemIOBaseAddressValue)},+ ; Com Io Base Address
{PermitShare, $(NoTitle),$(!REG_VT_DWORD), 1 },+
{ShareInterrupt, $(NoTitle),$(!REG_VT_DWORD), 1}}
Shell $(UtilityInf), AddValueList, $(MyNewSerialHandle), $(NewValueList)
CloseRegKey $(MyNewSerialHandle)
;add comm port info to HARDWARE\DEVICEMAP\SERIALCOMM section
OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP\SERIALCOMM" $(MAXIMUM_ALLOWED) MyNewSerialHandle
Ifstr $(MyNewSerialHandle) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" "HARDWARE\DEVICEMAP" $(MAXIMUM_ALLOWED) SerialKey
CreateRegKey $(SerialKey) {"SERIALCOMM",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" MyNewSerialHandle
CloseRegKey $(SerialKey)
Endif
SetRegValue $(MyNewSerialHandle) {"Serial3Com",$(NoTitle),$(!REG_VT_SZ),"COM"$(ComPortValue)}
CloseRegKey $(MyNewSerialHandle)
; add comm port info to SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports section
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion\Ports" $(MAXIMUM_ALLOWED) MyNewSerialHandle
Ifstr $(MyNewSerialHandle) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows NT\CurrentVersion" $(MAXIMUM_ALLOWED) SerialKey
CreateRegKey $(SerialKey) {"Ports",0,GenericClass} "" $(MAXIMUM_ALLOWED) "" MyNewSerialHandle
CloseRegKey $(SerialKey)
Endif
SetRegValue $(MyNewSerialHandle) {"COM"$(ComPortValues)":",$(NoTitle),$(!REG_VT_SZ),"9600,n,8,1"}
CloseRegKey $(MyNewSerialHandle)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
Debug-Output "Registry error: Add value list"
goto fatalregistry
endif
EndWait
goto successful
bindingadapter =+
set Error = "Binding: Sorry, not yet implemented."
goto fatal
removeadapter = +
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
else
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $(!NTN_RegBase)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
;Vivek
;***************************************************************
; Remove associated Com port
;***************************************************************
Debug-Output "<DBG> Starting removal of COM PORT .... "
Debug-Output "<DBG> !NTN_RegBase = "$(!NTN_RegBase)
Debug-Output "<DBG> Manufacturer = "$(Manufacturer)
Debug-Output "<DBG> ProductKeyName = "$(ProductKeyName)
Debug-Output "<DBG> ProductSoftwareName = "$(ProductSoftwareName)
set AdapterName = $(!NTN_RegBase)
Split-String $(AdapterName), "\", CardInfo
Debug-Output "<DBG> CardInfo = "$(CardInfo)
set AdapterNumber = *($(CardInfo),11)
set ComPortName = $(ComPortPrefix)$(AdapterNumber)
Debug-Output "<DBG> ComPortName = "$(ComPortName)
Debug-Output "<DBG> AdapterNumber = "$(AdapterNumber)
OpenRegKey $(!REG_H_LOCAL) "" "SYSTEM\CurrentControlSet\Services\Serial\Parameters" $(MAXIMUM_ALLOWED) SerialHandle
DeleteRegTree $(SerialHandle) $(ComPortName)
CloseRegKey $(SerialHandle)
;Vivek
endif
ifstr(i) (*($(CurrentVersionValue),4)) == $(NT400VersionConstant)
Debug-Output "$(InfFile) $(Option): Windows NT 4.00 remove icon"
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows\CurrentVersion\Run" $(!REG_KEY_ALL_ACCESS) KeyNt
set TrayIconList = COMSMDEXE
DeleteRegValue $(KeyNt) $(TrayIconList)
CloseRegKey $(KeyNt)
endif
RunProgram ExitCode "Windows Directory" "" UN3C556.EXE "-inf"
goto end
UpgradeSoftware = +
ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
GetRegValue $(KeyProduct),"MajorVersion", VersionInfo
set Version = *($(VersionInfo), 4)
Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set !UG_Filename = $($R0)
ifstr(i) $(!UG_Filename) != ""
install "Install-Update"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
goto fatal
endif
endif
SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)}
SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)}
ifint $(Version) != $(ProductVersion)
endif
CloseRegKey $(KeyProduct)
else
goto fatalregistry
endif
else
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) +
$(MAXIMUM_ALLOWED) NetworkCardKey
Ifstr(i) $(NetworkCardKey) != $(KeyNull)
GetRegValue $(NetworkCardKey),"ServiceName", ServiceNameInfo
set ServiceName = *($(ServiceNameInfo), 4)
OpenRegKey $(NetworkCardKey) "" "NetRules" +
$(MAXIMUM_ALLOWED) NetRuleKey
Ifstr(i) $(NetRuleKey) != $(KeyNull)
else
goto fatalregistry
endif
CloseRegKey $(NetRules)
CloseRegKey $(NetworkCardKey)
else
goto fatalregistry
endif
OpenRegKey $(!REG_H_LOCAL) "" +
$(!NTN_ServiceBase)"\"$(ServiceName) +
$(MAXIMUM_ALLOWED) ServiceKey
Ifstr(i) $(ServiceKey) != $(KeyNull)
CloseRegKey $(ServiceKey)
else
goto fatalregistry
endif
endif
goto end
successful = +
goto end
abandon = +
ForListDo $(OEM_ABANDON_OPTIONS)
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $($)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
EndForListDo
Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), FALSE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
warning = +
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(to)
else-ifstr(i) $($R1) == "CANCEL"
goto $(from)
else
goto "end"
endif
nonfatalinfo = +
Set Severity = STATUS
Set CommonStatus = STATUS_USERCANCEL
goto nonfatalmsg
nonfatal = +
Set Severity = NONFATAL
goto nonfatalmsg
nonfatalmsg = +
ifstr(i) $(Error) == ""
Set Severity = NONFATAL
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(from)
else
goto "end"
endif
fatalregistry = +
Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
fataldetect = +
Shell $(UtilityInf),RegistryErrorString,CANNOT_DETECT
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error: cannot get an error string."
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
fatal = +
ifstr(i) $(Error) == ""
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
goto setfailed
ShellCodeError = +
set DlgType = "MessageBox"
set STF_MB_TITLE = $(ShellCodeErrorTitle)
set STF_MB_TEXT = $(ShellCodeErrorText)
set STF_MB_TYPE = 1
set STF_MB_ICON = 3
set STF_MB_DEF = 1
ui start "Error Message"
goto setfailed
setfailed = +
set CommonStatus = STATUS_FAILED
ifstr(i) $(OEM_ABANDON_ON) == TRUE
set OEM_ABANDON_ON = FALSE
goto abandon
endif
goto end
end = +
goto term
term = +
Return $(CommonStatus)
[DebugConfiguration]
Set InfName = "OEMSETNT.INF"
return
[Install-Option]
set STF_VITAL = ""
ifstr(i) $(AddCopy) == "YES"
AddSectionFilesToCopyList Files-$(NDIS_VER) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
ifstr(i) (*($(CurrentVersionValue),4)) != $(NT400VersionConstant)
AddSectionFilesToCopyList Files-SERIAL $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
endif
endif
ifstr(i) $(DoCopy) == "YES"
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
endif
Exit
[Install-Update]
set STF_VITAL = ""
set STF_OVERWRITE = "VERIFYSOURCEOLDER"
AddSectionFilesToCopyList Files-3nicdiag $(SrcDir)win32 $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-HwDll $(SrcDir)WINNT $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-$(NDIS_VER) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
AddSectionFilesToCopyList Files-SERIAL $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH)
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
exit
[Install-Dll]
set STF_VITAL = ""
AddSectionFilesToCopyList Files-Dll $(SrcDir) $(!STF_WINDOWSSYSPATH)
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
exit
[Install-3nicdiag]
set STF_VITAL = ""
AddSectionFilesToCopyList Files-3nicdiag $(SrcDir)win32 $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-HwDll $(SrcDir)WINNT $(!STF_WINDOWSSYSPATH)
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
Exit
[Install-TrayAndCpl]
set STF_VITAL = ""
AddSectionFilesToCopyList Files-TrayAndCpl $(SrcDir)win32 $(!STF_WINDOWSSYSPATH)
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
Exit
[Source Media Descriptions]
1 = "Windows NT Setup Disk #1"
2 = "3Com FEM556-TX Fast EtherLink PC Card Installation Disk"
[ProductType]
STF_PRODUCT = Winnt
STF_PLATFORM = I386
[Files-Inf]
2, OEMSETNT.INF, SIZE=60000, RENAME=$(!UG_Filename)
[Files-Dll]
2, EL3C556.DLL, SIZE=50000
[Files-3nicdiag]
2,wnicdiag.exe, SIZE=300000
2,wnicdiag.hlp, SIZE=50000
2,wvaraddr.txt, SIZE=1000
2,un3c556.exe, SIZE=100000
[Files-HwDll]
2,hwaccess.dll, SIZE=90000
2,pcomdrv.sys, SIZE=9000
2,wc556cfg.dll, SIZE=90000
[Files-TrayAndCpl]
2,comsmd.exe, SIZE=10000
[Files-NDIS4]
2,FEM556N4.SYS , SIZE=60000
[Files-NDIS3]
2,FEM556N3.SYS , SIZE=60000
[Files-SERIAL]
2,SERIAL3.SYS , SIZE=60000
[LanguagesSupported]
ENG
[AllFileConstantsENG]
ProCaption = "Windows NT Setup"
ProCancel = "Cancel"
ProCancelMsg = "Windows NT Networking is not correctly installed. "+
"Are you sure you want to cancel copying files?"
ProCancelCap = "Network Setup Message"
ProText1 = "Copying:"
ProText2 = "To:"
DialogDllName = "EL3C556.DLL"
[FileConstantsENG-FEM556]
FunctionTitle = $(GenericAdapterName)" Setup"$(GenericInfVersion)
ProductSoftwareTitle = $(GenericDriverName)
ProductHardwareTitle = $(GenericAdapterName)
IRQList = ^(IRQChoices, 1)
IRQValues = ^(IRQChoices, 2)
InterruptStyleValues = ^(InterruptStyleChoices, 2)
IOBaseAddrList = ^(IOBaseAddrChoices, 1)
IOBaseAddrValues = ^(IOBaseAddrChoices, 2)
ModemIOBaseAddressList = ^(ModemIOBaseChoices,1)
ModemIOBaseAddressValues = ^(ModemIOBaseChoices,2)
MemoryAddrList = ^(MemoryAddrChoices,1)
MemoryAddrValues = ^(MemoryAddrChoices,2)
ComPortList = ^(ComPortChoices, 1)
ComPortValues = ^(ComPortChoices, 2)
;Vivek
ModemIrqList = ^(ModemIrqChoices,1)
ModemIrqValues = ^(ModemIrqChoices,2)
;Vivek
[DialogConstantsENG-FEM556]
Help = "&Help"
Exit = "Cancel"
OK = "OK"
HelpContext = ""
Continue = "Continue"
Cancel = "Cancel"
[FileDependentDlgENG-FEM556]
DlgType = "RadioCombination"
DlgTemplate = "EL3C556"
Caption = $(FunctionTitle)
HelpContext = $(!IDH_DB_OEMNADE2_INS)
CBOptionsGreyed = {}
NotifyFields = {NO, NO, NO, NO}
Combo1Label = "I/O Port:"
Combo2Label = "Interrupt:"
Combo3Label = "Memory:"
Combo4Label = "Com Port:"
Combo1List = $(IOBaseAddrList)
Combo1Out = $(IOBaseAddrValue)
Combo2List = $(IRQList)
Combo2Out = $(IRQValue)
Combo3List = $(MemoryAddrList)
Combo3Out = $(MemoryAddrValue)
Combo4List = $(ComPortList)
Combo4Out = $(ComPortValue)
Combo5List = $(IRQList)
Combo5Out = $(ModemInterruptNumberValue)
ComboListItemsIn = {Combo1List,Combo2List,Combo3List,Combo4List,Combo5List}
ComboListItemsOut = {Combo1Out,Combo2Out,Combo3Out,Combo4Out,Combo5Out}
EditTextIn = {"",""}
EditTextLim = {"",""}
[MemoryAddrChoices]
;Vivek
MA_0 = "Auto", 0
;Vivek
MA_1 = "0xC8000", 819200
MA_2 = "0xC9000", 823296
MA_3 = "0xCA000", 827392
MA_4 = "0xCB000", 831488
MA_5 = "0xCC000", 835584
MA_6 = "0xCD000", 839680
MA_7 = "0xCE000", 843776
MA_8 = "0xCF000", 847872
MA_9 = "0xD0000", 851968
MA_10 = "0xD1000", 856064
MA_11 = "0xD2000", 860160
MA_12 = "0xD3000", 864256
MA_13 = "0xD4000", 868352
MA_14 = "0xD5000", 872448
MA_15 = "0xD6000", 876544
MA_16 = "0xD7000", 880640
MA_17 = "0xD8000", 884736
MA_18 = "0xD9000", 888832
MA_19 = "0xDA000", 892928
MA_20 = "0xDB000", 897024
MA_21 = "0xDC000", 901120
MA_22 = "0xDD000", 905216
MA_23 = "0xDE000", 909312
MA_24 = "0xDF000", 913408
MA_25 = "0xE0000", 917504
MA_26 = "0xE1000", 921600
MA_27 = "0xE2000", 925696
MA_28 = "0xE3000", 929792
MA_29 = "0xE4000", 933888
MA_30 = "0xE5000", 937984
MA_31 = "0xE6000", 942080
MA_32 = "0xE7000", 946176
MA_33 = "0xE8000", 950272
MA_34 = "0xE9000", 954368
MA_35 = "0xEA000", 958464
MA_36 = "0xEB000", 962560
MA_37 = "0xEC000", 966656
MA_38 = "0xED000", 970752
MA_39 = "0xEE000", 974848
MA_40 = "0xEF000", 978944
;Vivek
[ModemIrqChoices]
MdmIrq_1 = "4",4
MdmIrq_2 = "3",3
MdmIrq_3 = "4",4
MdmIrq_4 = "3",3
;Vivek
[ComPortChoices]
CP_1 = "COM1", 1
CP_2 = "COM2", 2
CP_3 = "COM3", 3
CP_4 = "COM4", 4
[ModemIOBaseChoices]
MdmIOBase_1 = "0x3F8",1016
MdmIOBase_2 = "0x2F8",760
MdmIOBase_3 = "0x3E8",1000
MdmIOBase_4 = "0x2E8",744
[MediaTypeChoices]
MT_1 = "TP (10BaseT)", 0
MT_2 = "COAX (10Base2)", 1
[IRQChoices]
;Vivek
IRQ_0 = "Auto",0
;Vivek
IRQ_1 = "3",3
IRQ_2 = "5",5
IRQ_3 = "7",7
IRQ_4 = "9",9
IRQ_5 = "10",10
IRQ_6 = "11",11
IRQ_7 = "12",12
IRQ_8 = "15",15
[IOBaseAddrChoices]
;Vivek
IOBase_0 = "Auto",0
;Vivek
IOBase_1 = "0x300",768
IOBase_2 = "0x200",512
IOBase_3 = "0x210",528
IOBase_4 = "0x220",544
IOBase_5 = "0x230",560
IOBase_6 = "0x1E0",480
IOBase_7 = "0x250",592
IOBase_8 = "0x260",608
IOBase_9 = "0x270",624
IOBase_10 = "0x280",640
IOBase_11 = "0x290",656
IOBase_12 = "0x2A0",672
IOBase_13 = "0x2B0",688
IOBase_14 = "0x2C0",704
IOBase_15 = "0x2D0",720
IOBase_16 = "0x2E0",736
IOBase_17 = "0x2F0",752
IOBase_18 = "0x310",784
IOBase_19 = "0x320",800
IOBase_20 = "0x330",816
IOBase_21 = "0x340",832
IOBase_22 = "0x350",848
IOBase_23 = "0x360",864
IOBase_24 = "0x370",880
IOBase_25 = "0x380",896
IOBase_26 = "0x390",912
IOBase_27 = "0x3A0",928
IOBase_28 = "0x3B0",944
IOBase_29 = "0x3C0",960
IOBase_30 = "0x3D0",976
IOBase_31 = "0x1F0",496
IOBase_32 = "0x3F0",1008
; -------------------------- BEGIN FORCE FIX - Vivek
[install-update-modem-info]
OpenRegKey $(!REG_H_LOCAL) "" $(ZZZComPort) $(MAXIMUM_ALLOWED) +
ZZZHandle
ifstr $(ZZZHandle) == $(KeyNull)
Debug-Output "<DBG: FORCE> OpenRegKey "$(ZZZComPort)" failed"
goto done_update_modem_info
endif
Debug-Output "<DBG: FORCE> GetRegValue DosDevices"
GetRegValue $(ZZZHandle) "DosDevices" DosDevicesValue
set DosDevicesValueType = *($(DosDevicesValue), 3)
set DosDevicesValueData = *($(DosDevicesValue), 4)
ifint $(DosDevicesValueType) != $(!REG_VT_SZ)
Debug-Output +
"<DBG: FORCE> Bad DosDevices "$(ZZZComPort)" "$(DosDevicesValue)
goto done_update_modem_info
endif
GetRegValue $(ZZZHandle) "PortAddress" PortAddressValue
set PortAddressValueType = *($(PortAddressValue), 3)
set PortAddressValueData = *($(PortAddressValue), 4)
ifint $(PortAddressValueType) != $(!REG_VT_DWORD)
Debug-Output +
"<DBG: FORCE> Bad PortAddress "$(ZZZComPort)" "$(PortAddressValue)
goto done_update_modem_info
endif
GetRegValue $(ZZZHandle) "Interrupt" InterruptValue
set InterruptValueType = *($(InterruptValue), 3)
set InterruptValueData = *($(InterruptValue), 4)
ifint $(InterruptValueType) != $(!REG_VT_DWORD)
Debug-Output +
"<DBG: FORCE> Bad Interrupt "$(ZZZComPort)" "$(InterruptValue)
goto done_update_modem_info
endif
; now update the correct modem info
Debug-Output +
"<DBG: FORCE> "$(DosDevicesValueData)": iobase = "$(PortAddressValueData)", irq = "$(InterruptValueData)
ifstr(i) $(DosDevicesValueData) == "COM1"
set comNumber = 1
else-ifstr(i) $(DosDevicesValueData) == "COM2"
set comNumber = 2
else-ifstr(i) $(DosDevicesValueData) == "COM3"
set comNumber = 3
else-ifstr(i) $(DosDevicesValueData) == "COM4"
set comNumber = 4
else
goto done_update_modem_info
endif
set-dectohex PortAddressValueDataHex = $(PortAddressValueData)
set-dectohex InterruptValueDataHex = $(InterruptValueData)
Debug-Output +
"<DBG: FORCE> PortAddressValueDataHex = "$(PortAddressValueData)
Debug-Output +
"<DBG: FORCE> InterruptValueDataHex = "$(InterruptValueData)
;
; Change ModemIOBaseAddressValues
;
set oldList = $(ModemIOBaseAddressValues)
set itemNumberToReplace = $(comNumber)
set newData = $(PortAddressValueData)
set return_addr = replace_modem_io_base
goto replace_list_item
replace_modem_io_base = +
set ModemIOBaseAddressValues = $(newList)
;
; Change ModemIOBaseAddressList
;
set oldList = $(ModemIOBaseAddressList)
set itemNumberToReplace = $(comNumber)
set newData = $(PortAddressValueDataHex)
set return_addr = replace_modem_io_base_list
goto replace_list_item
replace_modem_io_base_list = +
set ModemIOBaseAddressList = $(newList)
;
; Change ModemIrqValues
;
set oldList = $(ModemIrqValues)
set itemNumberToReplace = $(comNumber)
set newData = $(InterruptValueData)
set return_addr = replace_modem_irq
goto replace_list_item
replace_modem_irq = +
set ModemIrqValues = $(newList)
;
; Change ModemIrqList
;
set oldList = $(ModemIrqList)
set itemNumberToReplace = $(comNumber)
set newData = $(InterruptValueDataHex)
set return_addr = replace_modem_irq_list
goto replace_list_item
replace_modem_irq_list = +
set ModemIrqList = $(newList)
done_update_modem_info = +
ifstr $(ZZZHandle) != $(KeyNull)
CloseRegKey $(ZZZHandle)
endif
exit
replace_list_item = +
;
; INPUT: needs the following variables to be initialized
; - oldList
; - itemNumberToReplace
; - newData
; - return_addr (i.e. label to jump back to)
; OUTPUT: returns with the newList initialized
;
;Debug-Output "<DBG: FORCE> Replacing item number "$(itemNumberToReplace)" in the list "$(oldList)" with the data "$(newData)
set newList = {}
ForListDo $(oldList)
ifint $(#) == $(itemNumberToReplace)
set newList = >($(newList), $(newData))
else
set newList = >($(newList), $($))
endif
EndForListDo
goto $(return_addr)
;-------------------------- END FORCE FIX
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.