;********************************************************************
; The PCI Ethernet miniport driver oemsetup file for WinNT 3.5x,
; WinNT 4.0 (NDIS 4.0 driver)
;
; This file will be copied in \WinNT\System32 under name oemnadXX.inf i.e.
; \WinNT\System32\oemnadXX.inf
;********************************************************************
[Identification]
OptionType = NetAdapter
[PlatformsSupported]
PCI
[Options]
SKYNET
[FileConstants]
;!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
; All info dependent from DEV = 2102, 2103,.... goes here.
sVendorID = "5072" ;; 0x13D0 is OUR Vendor ID
; For switching for different boards - CHANHE SETTINGS ONLY HERE_!!!!!!!!!!!!!!!!!
; Values for board - 0x2102
; sDeviceID = "8450" ;; 0x2102 is OUR Device ID
; sxDeviceID = "0x2102" ;; 0x2102
; SKYNETCFID = 553784272 ;; 0x210213D0 - B2C2Inc DEV_VEN ID
; Values for board - 0x2103
sDeviceID = "8451" ;; 0x2103 is OUR Device ID
sxDeviceID = "0x2103" ;; 0x2103
SKYNETCFID = 553849808 ;; 0x210313D0 - B2C2Inc DEV_VEN ID
;!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
UtilityInf = "UTILITY.INF"
subroutineinf = "SUBROUTN.INF"
SoftwareType = "driver"
Exit_Code = 0
NetEventDLL = "%SystemRoot%\System32\netevent.dll;%SystemRoot%\System32\drivers\SKYNET.SYS"
; NetEventDLL = "%SystemRoot%\System32\netevent.dll"
IoLogMsgDLL = "%SystemRoot%\System32\IoLogMsg.dll"
Manufacturer = "B2C2Inc"
ProductMajorVersion = "0"
ProductMinorVersion = "03"
ProductVersion = $(ProductMajorVersion)"."$(ProductMinorVersion)
ProductSoftwareName = "SKYNET"
ProductSoftwareImagePath = "%SystemRoot%\System32\drivers\SKYNET.SYS"
NetRuleSoftwareType = "SKYNETSys ndisDriver SKYNETDriver"
NetRuleSoftwareUse = $(SoftwareType)
NetRuleSoftwareBindForm = """SKYNETSys"" yes no container"
NetRuleSoftwareClass = {"SKYNETDriver basic"}
NetRuleSoftwareBindable = {"SKYNETDriver SKYNETAdapter non exclusive 100"}
ProductHardwareName = "SKYNET"
NetRuleHardwareBindForm = " yes yes container"
ProductKeyName = $(!NTN_SoftwareBase)"\"$(Manufacturer)"\"$(ProductSoftwareName)"\CurrentVersion"
ParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters"
MyTunerParamKeyName = $(!NTN_ServiceBase)"\"$(ProductHardwareName)"\Parameters\UserTunerParams"
; FunctionTitle = "B2C2Inc, Data\Vid\Aud "$(sxDeviceID)" PCI Adapter Setup"
; ProductSoftwareDescription = "B2C2Inc, Data\Vid\Aud "$(sxDeviceID)" PCI Adapter Driver"
; ProductSoftwareTitle = "B2C2Inc, Data\Vid\Aud "$(sxDeviceID)" PCI Adapter Driver"
FunctionTitle = "B2C2 Broadband Receiver PCI Adapter"
ProductSoftwareDescription = "B2C2 Broadband Receiver PCI Adapter"
ProductSoftwareTitle = "B2C2 Broadband Receiver PCI Adapter"
; ProductHardwareSKYNETTitle = "B2C2Inc, Data\Vid\Aud "$(sxDeviceID)" PCI Adapter"
; ProductHardwareSKYNETDescription = "B2C2Inc, Data\Vid\Aud "$(sxDeviceID)" PCI Adapter"
ProductHardwareSKYNETTitle = "B2C2 Broadband Receiver PCI Adapter"
ProductHardwareSKYNETDescription = "B2C2 Broadband Receiver PCI Adapter"
NetRuleHardwareSKYNETType = "SKYNET SKYNETAdapter"
NetRuleHardwareSKYNETClass = {"SKYNETAdapter basic"}
AdapterSKYNETType = 5 ;; PCI board
;++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
;===System(Standard Intel)Parameters===
nNumRfd = 128
;===_UserTunerParams_===
nEnableKernelTunerControl = 1
nTransponderFreq_KHz = 12515000
nLnbFreq_KHz = 11250000
nSymbolRate_KBauds = 20000
nStdIndexFec = 6
nStdIndexPolarity = 1
nStdIndexToneFreq = 0
nTunerTimerPeriodMs = 100
nTunerWaitLockTimeMs = 400
;===_UserHwParams_===
nBoard0x2102UseTimer = 1
nRunningNonStopDma1Dma2 = 0
nRunningNonStopDma1Dma2_Default_Is_0 = 0
nSizeOfBufDMA1 = 481280
nSizeOfBufDMA2 = 0
nUserTimerPeriodMs = 10
nSizeOfTimeIrqDMA1 = 0
nSizeOfTimeIrqDMA2 = 0
nUseSmartCard = 0
nUseMemSpaceRegAccess = 1
nSizeOfSubBufDMA1 = 64
nUseSubBufDMA1 = 0
nResetChip = 0
;===_UserSwParams_===
nWinOsVersionMaj = 4
nWinOsVersionMin = 0
nWinOsVersionSvcPack = 0 //???
;++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
[GeneralConstants]
from = ""
to = ""
ExitCodeOk = 0
ExitCodeCancel = 1
ExitCodeFatal = 2
KeyNull = ""
MAXIMUM_ALLOWED = 33554432
RegistryErrorIndex = NO_ERROR
KeyProduct = ""
KeyParameters = ""
TRUE = 1
FALSE = 0
NoTitle = 0
ExitState = "Active"
OldVersionExisted = $(FALSE)
DriverPath = $(!STF_NTPATH)\drivers
NT350VersionConstant = "3.50"
NT310VersionConstant = "3.10"
; DriverSrcDir = ""
[date]
Now = {} ? $(!LIBHANDLE) GetSystemDate
[Identify]
Debug-Output "$(InfFile) $(Option): [Identify]"
read-syms Identification
set Status = STATUS_SUCCESSFUL
set Identifier = $(OptionType)
set Media = #("Source Media Descriptions", 1, 1)
Return $(Status) $(Identifier) $(Media)
[ReturnOptions]
Debug-Output "$(InfFile) $(Option): [ReturnOptions]"
set Status = STATUS_FAILED
set OptionList = {}
set OptionTextList = {}
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) in $(LanguageList)
ifstr(i) $($1) == ""
goto returnoptions
endif
set PlatformList = ^(PlatformsSupported, 1)
Ifcontains(i) $($1) in $(PlatformList)
goto returnoptions
else
set Status = STATUS_NOTSUPPORTED
goto finish_ReturnOptions
endif
else
set Status = STATUS_NOLANGUAGE
goto finish_ReturnOptions
endif
returnoptions = +
Debug-Output "$(InfFile) $(Option): returnoptions = +"
set OptionList = ^(Options, 1)
set OptionTextList = ^(OptionsText$($0), 1)
set Status = STATUS_SUCCESSFUL
finish_ReturnOptions = +
Debug-Output "$(InfFile) $(Option): finish_ReturnOptions = +"
Return $(Status) $(OptionList) $(OptionTextList)
[InstallOption]
set !G:DebugOutputControl = 1
set Option = $($1)
set SrcDir = $($2)
set AddCopy = $($3)
set DoCopy = $($4)
set DoConfig = $($5)
Debug-Output "$(InfFile) $(Option): Starting: [InstallOption]"
Debug-Output "$(InfFile) $(Option): Starting: Option = $(Option)"
Debug-Output "$(InfFile) $(Option): Starting: SrcDir = $(SrcDir)"
Debug-Output "$(InfFile) $(Option): Starting: AddCopy = $(AddCopy)"
Debug-Output "$(InfFile) $(Option): Starting: DoCopy = $(DoCopy)"
Debug-Output "$(InfFile) $(Option): Starting: DoConfig = $(DoConfig)"
; set DriverSrcDir = $(SrcDir)
; Debug-Output "$(InfFile) $(Option): Starting: DriverSrcDir = $(DriverSrcDir)"
set LanguageList = ^(LanguagesSupported, 1)
Ifcontains(i) $($0) NOT-IN $(LanguageList)
Return STATUS_NOLANGUAGE
endif
set-subst LF = "\n"
read-syms GeneralConstants
read-syms FileConstants
read-syms DialogConstants$(!STF_LANGUAGE)
ifstr(i) $(!NTN_Origination) == "NCPA"
set Continue = "OK"
endif
read-syms FileConstants$(!STF_LANGUAGE)
detect date
set-title $(Function$(Option)Title)
set to = Begin
set from = Begin
set CommonStatus = STATUS_SUCCESSFUL
EndWait
Begin = +
Debug-Output "$(InfFile) $(Option): Starting: Begin = +"
set CurrentVersionValue = ""
OpenRegKey $(!REG_H_LOCAL) "" "SOFTWARE\Microsoft\Windows Nt\CurrentVersion" $(!REG_KEY_READ) KeyNt
Ifstr(i) $(KeyNt) != ""
GetRegValue $(KeyNt) "CurrentVersion" CurrentVersionValue
Debug-Output "$(InfFile) $(Option): WinNT CurrentVersion ="$(CurrentVersionValue)
CloseRegKey $(KeyNt)
Endif
ifstr(i) (*($(CurrentVersionValue),4)) == $(NT310VersionConstant) ;; NT v3.10 not supported!
Debug-Output "$(InfFile) $(Option): Configureadapter"
set Error = "Windows NT v3.10 is not support by this product"
goto fatal
endif
Ifstr(i) $(!NTN_InstallMode) == deinstall
set StartLabel = removeadapter
else-Ifstr(i) $(!NTN_InstallMode) == Update
set StartLabel = UpgradeSoftware
else-Ifstr(i) $(!NTN_InstallMode) == bind
set StartLabel = bindingadapter
else-Ifstr(i) $(!NTN_InstallMode) == configure
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(UtilityInf),RegistryErrorString,CANNOT_CONFIGURE_SOFTWARE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
set from = end
set to = end
goto nonfatalinfo
else
set StartLabel = configureadapter
endif
else
set StartLabel = installadapter
set OEM_ABANDON_OPTIONS = {}
set OEM_ABANDON_SOFTWARE = FALSE
set OEM_ABANDON_ON = TRUE
endif
Debug-Output "$(InfFile) $(Option): =================================================="
Debug-Output "$(InfFile) $(Option): STF_CWDIR is: "$(!STF_CWDIR)
Debug-Output "$(InfFile) $(Option): STF_SRCDIR is: "$(!STF_SRCDIR)
Debug-Output "$(InfFile) $(Option): STF_LANGUAGE is: "$(!STF_LANGUAGE)
Debug-Output "$(InfFile) $(Option): Option is: "$(Option)
Debug-Output "$(InfFile) $(Option): !STF_NCN_InstallMode is: "$(!NTN_InstallMode)
Debug-Output "$(InfFile) $(Option): !STF_NCDETECT is: "$(!STF_NCDETECT)
Debug-Output "$(InfFile) $(Option): !STF_NCOPTION is: "$(!STF_NCOPTION)
Debug-Output "$(InfFile) $(Option): !STF_NCDETCARD is: "$(!STF_NCDETCARD)
Debug-Output "$(InfFile) $(Option): !STF_NCDETINFO is: "$(!STF_NCDETINFO)
Debug-Output "$(InfFile) $(Option): !STF_GUI_UNATTENDED is: "$(!STF_GUI_UNATTENDED)
Debug-Output "$(InfFile) $(Option): !STF_BusType is: "$(!STF_BUSTYPE) ;; Primary Bus
Debug-Output "$(InfFile) $(Option): !STF_BusTypeList is: "$(!STF_BUSTYPELIST) ;; All Buses
Debug-Output "$(InfFile) $(Option): =================================================="
set from = $(fatal)
set to = $(fatal)
goto $(StartLabel)
installadapter = +
Debug-Output "$(InfFile) $(Option): installadapter = +"
;IvanK: Apr.13.2000: Stop line: install "Install-Hlp"
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; install "Install-Hlp"
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
Debug-Output "$(InfFile) $(Option): Ifstr $(KeyProduct) != $(KeyNull)"
CloseRegKey $(KeyProduct)
ifstr(i) !(NTN_RegBase) == $(ProductKeyName)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error: cannot get an error string."
goto ShellCodeError
endif
goto end
else
set OldVersionExisted = $(TRUE)
endif
Endif
; Debug-Output "$(InfFile) $(Option): Before set SrcDir to R1: SrcDir = $(SrcDir)"
; Set SrcDir = $($R1)
; Debug-Output "$(InfFile) $(Option): After set SrcDir to R1: SrcDir = $(SrcDir)"
Goto installproduct
configureadapter = +
Debug-Output "$(InfFile) $(Option): configureadapter = +"
Ifstr(i) $(KeyProduct) == $(KeyNull)
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_RegBase) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) == $(KeyNull)
Set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
Goto fatalregistry
Endif
Endif
Shell $(UtilityInf) FindService, $(KeyProduct)
Ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Endif
Ifstr(i) $($R0) != NO_ERROR
Goto fatalregistry
endif
set KeyParameters = $($R2)
CloseRegKey $($R1)
Ifstr $(KeyParameters) == $(KeyNull)
set RegistryErrorIndex = CANNOT_FIND_COMPONENT_SERVICE
goto fatalregistry
endif
set OldVersionExisted = $(TRUE)
set ValueName = ""
set ValueData = ""
set ValueStr = ""
set ValueList = {}
EnumRegValue $(KeyParameters) ValueList
ForListDo $(ValueList)
set ValueItem = $($)
set ValueName = *($(ValueItem),1)
set ValueData = *($(ValueItem),4)
Ifstr(i) $(ValueName) == "DuplexMode"
set DuplexModeIndex = $(ValueData)
endif
EndForListDo
set DuplexModeValue = *($(DuplexModeList), ~($(DuplexModeValues),$(DuplexModeIndex)))
ifstr(i) $(DuplexModeValue) == ""
set DuplexModeValue = *($(DuplexModeList), 1)
endif
adapteroptions = +
Debug-Output "$(InfFile) $(Option): adapteroptions = +"
set from = adapteroptions
;IvanK: Apr.13.2000: Stop lines
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; read-syms FileDependentDlg$(!STF_LANGUAGE)
; SetHelpFile $(!STF_WINDOWSSYSPATH)"\"sample.hlp 10 20 10
; ui start "InputDlg"
;
; ifstr(i) $(DLGEVENT) == "CONTINUE"
; set DuplexModeIndex = $(Combo1Out)
; ui pop 1
; else-ifstr(i) $(DLGEVENT) == "BACK"
; set CommonStatus = STATUS_USERCANCEL
; ui pop 1
; goto end
; else
; ui pop 1
; goto end
; endif
;
; set DuplexModeValue = *($(DuplexModeValues), ~($(DuplexModeList),$(DuplexModeIndex)))
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
ifstr(i) $(!NTN_InstallMode) == configure
goto updateparameters
endif
installproduct =+
Debug-Output "$(InfFile) $(Option): installproduct =+"
StartWait
set AdapterList = $($R1)
Debug-Output "$(InfFile) $(Option): AdapterList = $(AdapterList)"
ifint $(OldVersionExisted) == $(FALSE)
Debug-Output "$(InfFile) $(Option): OldVersion: $(OldVersionExisted) ?= $(FALSE)"
Ifstr(i) $(DoCopy) == "YES"
Debug-Output "$(InfFile) $(Option): DoCopy: $(DoCopy) ?= "YES""
Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) NO
; Shell $(UtilityInf), DoAskSource, $(!STF_CWDDIR), $(SrcDir) YES
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Goto ShellCodeError
Else-Ifstr(i) $($R0) == STATUS_FAILED
Shell $(UtilityInf) RegistryErrorString "ASK_SOURCE_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
Goto fatal
Else-Ifstr(i) $($R0) == STATUS_USERCANCEL
Goto successful
Endif
Debug-Output "$(InfFile) $(Option): Before set SrcDir to R1: SrcDir = $(SrcDir)"
Set SrcDir = $($R1)
Debug-Output "$(InfFile) $(Option): After set SrcDir to R1: SrcDir = $(SrcDir)"
Endif
install "Install-Option"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
Debug-Output "$(InfFile) $(Option): $(STF_INSTALL_OUTCOME) != STF_SUCCESS"
Shell $(UtilityInf) RegistryErrorString "UNABLE_COPY_FILE"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
endif
endif
OpenRegKey $(!REG_H_LOCAL) "" $(!NTN_ServiceBase)"\"$(ProductHardwareName) $(!REG_KEY_READ) KeyNt
CloseRegKey $(KeyNt)
Ifstr(i) $(KeyNt) == ""
Debug-Output "$(InfFile) $(Option): AddSoftwareComponent"
Debug-Output "$(InfFile) $(Option): --> $(Manufacturer)"
Debug-Output "$(InfFile) $(Option): --> $(ProductSoftwareName)"
Debug-Output "$(InfFile) $(Option): --> $(ProductSoftwareTitle)"
Debug-Output "$(InfFile) $(Option): --> $(STF_CONTEXTINFNAME)"
Debug-Output "$(InfFile) $(Option): --> $(ProductSoftwareImagePath)"
Debug-Output "$(InfFile) $(Option): --> $(NetEventDLL)"
Shell $(UtilityInf), AddSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), +
$(ProductSoftwareName), +
$(ProductSoftwareTitle), $(STF_CONTEXTINFNAME), +
$(ProductSoftwareImagePath), "kernel", "NDIS", {}, "",+
$(NetEventDLL)
Set OEM_ABANDON_SOFTWARE = TRUE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
CloseRegKey $($R4)
CloseRegKey $($R5)
goto fatalregistry
endif
Set SoftProductKey = $($R1)
Set SoftNetRuleKey = $($R2)
Set SoftServiceKey = $($R3)
Set SoftParameterKey = $($R4)
Set SoftLinkageKey = $($R5)
set NewValueList = {{SoftwareType,$(NoTitle),$(!REG_VT_SZ),$(SoftwareType)},+
{MajorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMajorVersion)},+
{MinorVersion,$(NoTitle),$(!REG_VT_DWORD),$(ProductMinorVersion)},+
{Title,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareTitle)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareDescription)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$(ProductSoftwareName)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(SoftProductKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftParameterKey)
CloseRegKey $(SoftLinkageKey)
goto fatalregistry
endif
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareType)},+
{use,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareUse)}, +
{bindform,$(NoTitle),$(!REG_VT_SZ),$(NetRuleSoftwareBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareClass)}, +
{bindable,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleSoftwareBindable)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Shell $(UtilityInf), AddValueList, $(SoftNetRuleKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
CloseRegKey $(SoftProductKey)
CloseRegKey $(SoftNetRuleKey)
CloseRegKey $(SoftServiceKey)
CloseRegKey $(SoftParameterKey)
CloseRegKey $(SoftLinkageKey)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
goto fatalregistry
endif
endif
set NTDetected = $(FALSE)
Debug-Output "$(InfFile) $(Option): About to look for 10/100M PCI Cards"
set TargetVersion = *($(CurrentVersionValue),4)
Debug-Output "$(InfFile) $(Option): Current Version:"$(TargetVersion)
ifstr $(TargetVersion) == $(NT350VersionConstant)
Debug-Output "Running on WindowsNT 3.50"
set Version350 = $(TRUE)
else
Debug-Output "Running on WindowsNT 3.51"
set Version350 = $(FALSE)
endif
ifint $(Version350) == $(TRUE)
Debug-Output "Running on WindowsNT v3.50, Not using PCI Detection!!!"
ifstr $(!STF_GUI_UNATTENDED) == "YES"
Debug-Output "$(InfFile) $(Option): Running in GUI unattended mode"
ifstr(i) $(!AutoNetInterfaceType) != ""
set BusInterfaceType = $(!AutoNetInterfaceType)
else
set BusInterfaceType = 5
endif
ifstr(i) $(!AutoNetBusNumber) != ""
set BusNumber = $(!AutoNetBusNumber)
else
set BusNumber = 0
endif
set NTDetected = $(FALSE)
set AdapterList = $(Option) ;; 1 Item to install
Debug-Output "$(InfFile) $(Option): BusInterfaceType = $(BusInterfaceType)"
Debug-Output "$(InfFile) $(Option): BusNumber = $(BusNumber)"
else
Debug-Output "$(InfFile) $(Option): Running 3.50 Bus Dialog"
set BusInterfaceType = 5
set BusNumber = 0
set NTDetected = $(FALSE)
Shell $(UtilityInf),GetBusTypeDialog,$(ProductHardware$(Option)Description) $(BusInterfaceType) $(BusNumber)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error."
goto ShellCodeError
endif
set BusInterfaceType = $($R1)
set BusNumber = $($R2)
set AdapterList = $(Option) ;; 1 Item to install
Debug-Output "$(InfFile) $(Option): BusInterfaceType = $(BusInterfaceType)"
Debug-Output "$(InfFile) $(Option): BusNumber = $(BusNumber)"
endif
else
Debug-Output "$(InfFile) $(Option): Running 3.51 using PCI Dectection"
;!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
set NTDetected = $(TRUE)
set VendorID = $(sVendorID) ;; 0x13D0 is OUR Vendor ID
set DeviceID = $(sDeviceID) ;; 0x2102 is OUR Device ID
;!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Debug-Output "$(InfFile) $(Option): VendorID = $(VendorID)"
Debug-Output "$(InfFile) $(Option): DeviceID = $(DeviceID)"
Shell $(UtilityInf), GetPCIInformation, $(VendorID) $(DeviceID)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R0) == {}
set Error = $(CANNOT_FIND_ANY_CARD)
set CommonStatus = USER_CANCEL
set from = end
goto nonfatal
endif
set AdapterList = $($R0)
endif
endif
Debug-Output "$(InfFile) $(Option): Before ForListDo: Adapterlist = $(AdatperList)"
ForListDo $(AdapterList)
Set InstallCard = "YES"
ifint $(NTDetected) == $(TRUE)
set DetectedBusNum = *($($),1)
set DetectedSlotNum = *($($),2)
Debug-Output "$(InfFile) $(Option): DetectedBusNumber = $(DetectedBusNum)"
Debug-Output "$(InfFile) $(Option): DetectedSlotNum = $(DetectedSlotNum)"
Shell $(UtilityInf), IsNetCardAlreadyInstalled, $(DetectedBusNum), +
$(DetectedSlotNum), $(ProductHardware$(Option)Description), $(ProductHardwareName)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr $($R0) != "NO_ERROR"
set Error = $($R0)
goto fatal
endif
ifstr(i) $($R1) == "YES"
set InstallCard = "NO"
endif
endif
ifstr(i) $(InstallCard) == "NO"
Debug-Output "$(InfFile) $(Option): Card Already at $(DetectedBusNum):$(DetectedSlotNum) already installed!"
set Error = "An adapter at $(DetectedBusNum):$(DetectedSlotNum) is already installed!"
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
else
Debug-Output "$(InfFile) $(Option): Installing Card at $(DetectedBusNum):$(DetectedSlotNum)!"
Shell $(UtilityInf), AddHardwareComponent, $(ProductHardwareName),$(STF_CONTEXTINFNAME),$(ProductKeyName)
ifint $($R4) != -1
Set OEM_ABANDON_OPTIONS = >($(OEM_ABANDON_OPTIONS), $(!NTN_SoftwareBase)"\Microsoft\Windows NT\CurrentVersion\NetworkCards\"$($R4))
endif
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != "NO_ERROR"
EndWait
CloseRegKey $($R1)
CloseRegKey $($R2)
CloseRegKey $($R3)
goto fatalregistry
endif
;IvanK: Apr.13.2000: Stop lines, displaying InputDialog - we don't need it !!!!!!!!!!!!
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; read-syms FileDependentDlg$(!STF_LANGUAGE)
; SetHelpFile $(!STF_WINDOWSSYSPATH)"\"sample.hlp 10 20 10
; ui start "InputDlg"
; set DuplexModeIndex = $(Combo1Out)
; ui pop 1
; set DuplexModeValue = *($(DuplexModeValues), ~($(DuplexModeList),$(DuplexModeIndex)))
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
Set HardNetCardKey = $($R1)
Set HardNetRuleKey = $($R2)
Set HardParameterKey = $($R3)
set AdapterNumber = $($R4)
;+++++++++++++++++++++++++++__MyStuff__+++++++++++++++++++++++++++++++++++
Debug-Output "$(InfFile) $(Option): Set AdapterNumber = $(AdapterNumber)"
Set UserTunerParameterKey = $(HardParameterKey)"\UserTunerParams"
Set UserHwParameterKey = $(HardParameterKey)"\UserHwParams"
Set UserSwParameterKey = $(HardParameterKey)"\UserSwParams"
Set KeyToOpen = ""
;+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
set NewValueList = {{Manufacturer,$(NoTitle),$(!REG_VT_SZ),$(Manufacturer)},+
{Title,$(NoTitle),$(!REG_VT_SZ),"["$($R4)"] "$(ProductHardware$(Option)Title)},+
{Description,$(NoTitle),$(!REG_VT_SZ),$(ProductHardware$(Option)Description)},+
{ProductName,$(NoTitle),$(!REG_VT_SZ),$(ProductHardwareName)},+
{ServiceName,$(NoTitle),$(!REG_VT_SZ),$($R5)},+
{InstallDate,$(NoTitle),$(!REG_VT_DWORD),*($(Now),1)}}
Shell $(UtilityInf), AddValueList, $(HardNetCardKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set BusTypeNum = 5
set BusMaster = "YES"
set Bus = "PCI"
ifstr(i) $(Option) == "SKYNET"
set CardType = 2
else
set CardType = 0
endif
ifint $(NTDetected) == $(TRUE)
set BusNumber = $(DetectedBusNum)
set SlotNum = $(DetectedSlotNum)
set BusInterfaceType = $(BusTypeNum)
Set NewValueList = {+
{BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNumber)},+
{Slot,$(NoTitle),$(!REG_VT_DWORD),$(SlotNum)}+
}
Debug-Output "$(InfFile) $(Option): Set HardwareParameterKey = $(NewValueList)"
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
Set NewValueList = { {SlotNumber,$(NoTitle),$(!REG_VT_DWORD),$(SlotNum)} }
Debug-Output "$(InfFile) $(Option): Set HardwareParameterKey = $(NewValueList)"
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
else
Set NewValueList = {+
{BusNumber,$(NoTitle),$(!REG_VT_DWORD),$(BusNumber)},+
}
Debug-Output "$(InfFile) $(Option): Set HardwareParameterKey = $(NewValueList)"
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
endif
;!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
;Adding parameters in key:Set HardParameterKey = $($R3)
; : which is:.....\Services\SKYNET2\Parameters
; We need(add) the next parameters: BusType, CardType, MediaType, AdapterCFID ans NumRfd !!!
Set NewValueList = {+
{BusType,$(NoTitle),$(!REG_VT_DWORD),$(BusInterfaceType)},+
{CardType,$(NoTitle),$(!REG_VT_DWORD),$(CardType)},+
{MediaType,$(NoTitle),$(!REG_VT_DWORD),1},+
{AdapterCFID,$(NoTitle),$(!REG_VT_DWORD),$($(Option)CFID)},+
{NumRfd,$(NoTitle),$(!REG_VT_DWORD),$(nNumRfd)},+
}
Debug-Output "$(InfFile) $(Option): Set HardwareParameterKey = $(NewValueList)"
Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
; set NewValueList = {{DuplexMode,$(NoTitle),$(!REG_VT_DWORD),$(DuplexModeValue)}}
; Debug-Output "$(InfFile) $(Option): $(HardParameterKey) = $(NewValueList)"
; Shell $(UtilityInf), AddValueList, $(HardParameterKey), $(NewValueList)
; ifint $($ShellCode) != $(!SHELL_CODE_OK)
; goto ShellCodeError
; endif
set TempProdName = """"$(ProductHardwareName)$(AdapterNumber)""""
set TempBindForm = $(TempProdName)$(NetRuleHardwareBindForm)
set NewValueList = {{type,$(NoTitle),$(!REG_VT_SZ),$(NetRuleHardware$(Option)Type)},+
{bindform,$(NoTitle),$(!REG_VT_SZ),$(TempBindForm)}, +
{class,$(NoTitle),$(!REG_VT_MULTI_SZ),$(NetRuleHardware$(Option)Class)}, +
{InfOption,$(NoTitle),$(!REG_VT_SZ),$(Option)}}
Debug-Output "$(InfFile) $(Option): HardwareRuleKey = $(NewValueList)"
Shell $(UtilityInf), AddValueList, $(HardNetRuleKey), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
CloseRegKey $(HardNetCardKey)
CloseRegKey $(HardNetRuleKey)
CloseRegKey $(HardParameterKey)
endif
EndForListDo
;++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
; Try to add our parameters in :.....\Services\SKYNETx\Parameters\TunerParameters !!!!!!!
;// O.K. THIS WORKS++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
;...\Parameters\UserTunerParams
Set KeyToOpen = $(!NTN_ServiceBase)"\"$(ProductHardwareName)$(AdapterNumber)"\Parameters\UserTunerParams"
Debug-Output "$(InfFile) $(Option): Set KeyToOpen = $(KeyToOpen)"
OpenRegKey $(!REG_H_LOCAL) "" $(KeyToOpen) $(MAXIMUM_ALLOWED) KeyParameters
ifstr $(KeyParameters) == $(KeyNull)
Debug-Output "$(InfFile) ***MyDump: O.K.: We DON'T HAVE key KeyToOpen = $(KeyToOpen) so, we will CREATE IT."
CreateRegKey $(!REG_H_LOCAL) {$(KeyToOpen),$(NoTitle),GenericClass} "" $(MAXIMUM_ALLOWED) "" KeyParameters
ifstr $(KeyParameters) != $(KeyNull)
Debug-Output "$(InfFile) ***MyDump: O.K.: We created key KeyToOpen = $(KeyToOpen)"
Set NewValueList = {+
{nEnableKernelTunerControl,$(NoTitle),$(!REG_VT_DWORD), $(nEnableKernelTunerControl) }, +
{nTransponderFreq_KHz, $(NoTitle),$(!REG_VT_DWORD), $(nTransponderFreq_KHz) }, +
{nLnbFreq_KHz, $(NoTitle),$(!REG_VT_DWORD), $(nLnbFreq_KHz) }, +
{nSymbolRate_KBauds, $(NoTitle),$(!REG_VT_DWORD), $(nSymbolRate_KBauds) }, +
{nStdIndexFec, $(NoTitle),$(!REG_VT_DWORD), $(nStdIndexFec) }, +
{nStdIndexPolarity, $(NoTitle),$(!REG_VT_DWORD), $(nStdIndexPolarity) }, +
{nStdIndexToneFreq, $(NoTitle),$(!REG_VT_DWORD), $(nStdIndexToneFreq) }, +
{nTunerTimerPeriodMs, $(NoTitle),$(!REG_VT_DWORD), $(nTunerTimerPeriodMs) }, +
{nTunerWaitLockTimeMs, $(NoTitle),$(!REG_VT_DWORD), $(nTunerWaitLockTimeMs) }, +
}
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "$(InfFile) ***Error: Shell CAN'T ADD PARAMETERS !!!???."
endif
CloseRegKey $(KeyParameters)
else
Debug-Output "$(InfFile) ***Error: Can't CREATE KEY: KeyToOpen = $(KeyToOpen)"
endif
else
Debug-Output "$(InfFile) ***Error: WE ALREADY HAVE THIS KEY. IT SHOULD NOT EXIST !!!???."
endif
;...\Parameters\UserHwParams
Set KeyToOpen = $(!NTN_ServiceBase)"\"$(ProductHardwareName)$(AdapterNumber)"\Parameters\UserHwParams"
Debug-Output "$(InfFile) $(Option): Set KeyToOpen = $(KeyToOpen)"
OpenRegKey $(!REG_H_LOCAL) "" $(KeyToOpen) $(MAXIMUM_ALLOWED) KeyParameters
ifstr $(KeyParameters) == $(KeyNull)
Debug-Output "$(InfFile) ***MyDump: O.K.: We DON'T HAVE key KeyToOpen = $(KeyToOpen) so, we will CREATE IT."
CreateRegKey $(!REG_H_LOCAL) {$(KeyToOpen),$(NoTitle),GenericClass} "" $(MAXIMUM_ALLOWED) "" KeyParameters
ifstr $(KeyParameters) != $(KeyNull)
Debug-Output "$(InfFile) ***MyDump: O.K.: We created key KeyToOpen = $(KeyToOpen)"
Set NewValueList = {+
{nBoard0x2102UseTimer, $(NoTitle),$(!REG_VT_DWORD), $(nBoard0x2102UseTimer) }, +
{nRunningNonStopDma1Dma2, $(NoTitle),$(!REG_VT_DWORD), $(nRunningNonStopDma1Dma2)},+
{nRunningNonStopDma1Dma2_Default_Is_0, $(NoTitle),$(!REG_VT_DWORD), $(nRunningNonStopDma1Dma2_Default_Is_0) }, +
{nSizeOfBufDMA1, $(NoTitle),$(!REG_VT_DWORD), $(nSizeOfBufDMA1) }, +
{nSizeOfBufDMA2, $(NoTitle),$(!REG_VT_DWORD), $(nSizeOfBufDMA2) }, +
{nUserTimerPeriodMs, $(NoTitle),$(!REG_VT_DWORD), $(nUserTimerPeriodMs) }, +
{nSizeOfTimeIrqDMA1, $(NoTitle),$(!REG_VT_DWORD), $(nSizeOfTimeIrqDMA1) }, +
{nSizeOfTimeIrqDMA2, $(NoTitle),$(!REG_VT_DWORD), $(nSizeOfTimeIrqDMA2) }, +
{nUseSmartCard, $(NoTitle),$(!REG_VT_DWORD), $(nUseSmartCard) }, +
{nUseMemSpaceRegAccess, $(NoTitle),$(!REG_VT_DWORD), $(nUseMemSpaceRegAccess) }, +
{nSizeOfSubBufDMA1, $(NoTitle),$(!REG_VT_DWORD), $(nSizeOfSubBufDMA1) }, +
{nUseSubBufDMA1, $(NoTitle),$(!REG_VT_DWORD), $(nUseSubBufDMA1) }, +
{nResetChip, $(NoTitle),$(!REG_VT_DWORD), $(nResetChip) }, +
}
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "$(InfFile) ***Error: Shell CAN'T ADD PARAMETERS !!!???."
endif
CloseRegKey $(KeyParameters)
else
Debug-Output "$(InfFile) ***Error: Can't CREATE KEY: KeyToOpen = $(KeyToOpen)"
endif
else
Debug-Output "$(InfFile) ***Error: WE ALREADY HAVE THIS KEY. IT SHOULD NOT EXIST !!!???."
endif
;...\Parameters\UserSwParams
Set KeyToOpen = $(!NTN_ServiceBase)"\"$(ProductHardwareName)$(AdapterNumber)"\Parameters\UserSwParams"
Debug-Output "$(InfFile) $(Option): Set KeyToOpen = $(KeyToOpen)"
OpenRegKey $(!REG_H_LOCAL) "" $(KeyToOpen) $(MAXIMUM_ALLOWED) KeyParameters
ifstr $(KeyParameters) == $(KeyNull)
Debug-Output "$(InfFile) ***MyDump: O.K.: We DON'T HAVE key KeyToOpen = $(KeyToOpen) so, we will CREATE IT."
CreateRegKey $(!REG_H_LOCAL) {$(KeyToOpen),$(NoTitle),GenericClass} "" $(MAXIMUM_ALLOWED) "" KeyParameters
ifstr $(KeyParameters) != $(KeyNull)
Debug-Output "$(InfFile) ***MyDump: O.K.: We created key KeyToOpen = $(KeyToOpen)"
Set NewValueList = {+
{nWinOsVersionMaj, $(NoTitle),$(!REG_VT_DWORD), $(nWinOsVersionMaj ) }, +
{nWinOsVersionMin, $(NoTitle),$(!REG_VT_DWORD), $(nWinOsVersionMin ) }, +
{nWinOsVersionSvcPack, $(NoTitle),$(!REG_VT_DWORD), $(nWinOsVersionSvcPack) }, +
}
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "$(InfFile) ***Error: Shell CAN'T ADD PARAMETERS !!!???."
endif
CloseRegKey $(KeyParameters)
else
Debug-Output "$(InfFile) ***Error: Can't CREATE KEY: KeyToOpen = $(KeyToOpen)"
endif
else
Debug-Output "$(InfFile) ***Error: WE ALREADY HAVE THIS KEY. IT SHOULD NOT EXIST !!!???."
endif
;++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
EndWait
goto successful
updateparameters =+
Debug-Output "$(InfFile) $(Option): updateparameters =+"
set HardParameterKey = $($R3)
set NewValueList = {{DuplexMode,$(NoTitle),$(!REG_VT_DWORD),$(DuplexModeValue)}}
Shell $(UtilityInf), AddValueList, $(KeyParameters), $(NewValueList)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
CloseRegKey $(KeyParameters)
goto successful
bindingadapter =+
Debug-Output "$(InfFile) $(Option): bindingadapter =+"
set Error = "Binding: Sorry, not yet implemented."
goto fatal
removeadapter = +
Debug-Output "$(InfFile) $(Option): removeadapter = +"
Debug-Output "$(InfFile) $(Option): ----> $(ProductKeyName), $(!NTN_RegBase)"
Ifstr(i) $(ProductKeyName) == $(!NTN_RegBase)
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
else
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $(!NTN_RegBase)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
UpgradeSoftware = +
Debug-Output "$(InfFile) $(Option): UpgradeSoftware = +"
OpenRegKey $(!REG_H_LOCAL) "" $(ProductKeyName) $(MAXIMUM_ALLOWED) KeyProduct
Ifstr $(KeyProduct) != $(KeyNull)
Shell $(UtilityInf), GetInfFileNameFromRegistry, $(KeyProduct)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
Debug-Output "ShellCode error"
goto ShellCodeError
endif
set !UG_Filename = $($R0)
install "Install-Update"
ifstr(i) $(STF_INSTALL_OUTCOME) != STF_SUCCESS
goto fatal
endif
SetRegValue $(KeyProduct) {MajorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMajorVersion)}
SetRegValue $(KeyProduct) {MinorVersion,$(NoTitle),$(!REG_VT_SZ),$(ProductMinorVersion)}
CloseRegKey $(KeyProduct)
else
goto fatalregistry
endif
goto end
successful = +
Debug-Output "$(InfFile) $(Option): successful = +"
goto end
abandon = +
Debug-Output "$(InfFile) $(Option): abandon = +"
ForListDo $(OEM_ABANDON_OPTIONS)
Shell $(UtilityInf), RemoveHardwareComponent, $(Manufacturer), +
$(ProductSoftwareName), $($)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
EndForListDo
Ifstr(i) $(OEM_ABANDON_SOFTWARE) == TRUE
Shell $(UtilityInf), RemoveSoftwareComponent, $(Manufacturer), +
$(ProductSoftwareName), FALSE
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set RegistryErrorIndex = $($R0)
Ifstr(i) $(RegistryErrorIndex) != NO_ERROR
goto fatalregistry
endif
endif
goto end
warning = +
Debug-Output "$(InfFile) $(Option): warning = +"
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "WARNING", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(to)
else-ifstr(i) $($R1) == "CANCEL"
goto $(from)
else
goto "end"
endif
nonfatalinfo = +
Debug-Output "$(InfFile) $(Option): nonfatalinfo = +"
Set CommonStatus = STATUS_USERCANCEL
Set Severity = STATUS
goto nonfatalmsg
nonfatal = +
Debug-Output "$(InfFile) $(Option): nonfatal = +"
Set Severity = NONFATAL
goto nonfatalmsg
nonfatalmsg = +
Debug-Output "$(InfFile) $(Option): nonfatalmsg = +"
ifstr(i) $(Error) == ""
Set Severity = NONFATAL
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), $(Severity), $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
ifstr(i) $($R1) == "OK"
goto $(from)
else
; goto "end"
goto "RemoveAdapter"
endif
fatalregistry = +
Debug-Output "$(InfFile) $(Option): fatalregistry = +"
Shell $(UtilityInf) RegistryErrorString $(RegistryErrorIndex)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
goto fatal
fatal = +
Debug-Output "$(InfFile) $(Option): fatal = +"
ifstr(i) $(Error) == ""
Shell $(UtilityInf) RegistryErrorString "SETUP_FAIL"
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
set Error = $($R0)
endif
Shell $(subroutineinf) SetupMessage, $(!STF_LANGUAGE), "FATAL", $(Error)
ifint $($ShellCode) != $(!SHELL_CODE_OK)
goto ShellCodeError
endif
goto setfailed
ShellCodeError = +
Debug-Output "$(InfFile) $(Option): ShellCodeError = +"
set DlgType = "MessageBox"
set STF_MB_TITLE = $(ShellCodeErrorTitle)
set STF_MB_TEXT = $(ShellCodeErrorText)
set STF_MB_TYPE = 1
set STF_MB_ICON = 3
set STF_MB_DEF = 1
ui start "Error Message"
goto setfailed
setfailed = +
Debug-Output "$(InfFile) $(Option): setfailed = +"
set CommonStatus = STATUS_FAILED
ifstr(i) $(OEM_ABANDON_ON) == TRUE
set OEM_ABANDON_ON = FALSE
goto abandon
endif
goto end
end = +
Debug-Output "$(InfFile) $(Option): end = +"
goto term
term = +
Debug-Output "$(InfFile) $(Option): term = +"
Return $(CommonStatus)
[Install-Option]
Debug-Output "$(InfFile) $(Option): [Install-Option]"
set STF_VITAL = ""
ifstr(i) $(AddCopy) == "YES"
Debug-Output "$(InfFile) $(Option): $(AddCopy) ?= "YES""
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
endif
ifstr(i) $(DoCopy) == "YES"
Debug-Output "$(InfFile) $(Option): $(DoCopy) ?= "YES""
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
endif
Exit
[Install-Hlp]
Debug-Output "$(InfFile) $(Option): [Install-Hlp]"
set STF_VITAL = ""
; AddSectionFilesToCopyList Files-Hlp $(SrcDir)WINNT $(!STF_WINDOWSSYSPATH)
; set !STF_NCPA_FLUSH_COPYLIST = TRUE
; CopyFilesInCopyList
Exit
[Install-Update]
Debug-Output "$(InfFile) $(Option): [Install-Update]"
set STF_VITAL = ""
set STF_OVERWRITE = "VERIFYSOURCEOLDER"
; AddSectionFilesToCopyList Files-Hlp $(SrcDir)WINNT $(!STF_WINDOWSSYSPATH)
AddSectionFilesToCopyList Files-Inf $(SrcDir) $(!STF_WINDOWSSYSPATH)
; AddSectionFilesToCopyList Files-$(Option) $(SrcDir)WINNT $(!STF_WINDOWSSYSPATH)\drivers
AddSectionFilesToCopyList Files-$(Option) $(SrcDir) $(!STF_WINDOWSSYSPATH)\drivers
set !STF_NCPA_FLUSH_COPYLIST = TRUE
CopyFilesInCopyList
exit
[Source Media Descriptions]
; 1 = "B2C2Inc, Data\Video\Audio PCI Driver Disk"
1 = "B2C2 Broadband Receiver PCI Adapter"
[ProductType]
STF_PRODUCT = Winnt
STF_PLATFORM = I386
[Files-Inf]
1, oemsetup.inf, SIZE=1000, RENAME=$(!UG_Filename)
;[Files-Hlp]
;1, SAMPLE.HLP , SIZE=10000
[Files-SKYNET]
1,SKYNET.SYS , SIZE=700000
[LanguagesSupported]
ENG
[OptionsTextENG]
; SKYNET = "B2C2Inc, Data\Video\Audio PCI Adapter"
SKYNET = "B2C2 Broadband Receiver PCI Adapter"
[FileConstantsENG]
ProCaption = "Windows NT Setup"
ProCancel = "Cancel"
ProCancelMsg = "Windows NT Networking is not correctly installed. "+
"Are you sure you want to cancel copying files?"
ProCancelCap = "Network Setup Message"
ProText1 = "Copying:"
ProText2 = "To:"
DuplexModeList = ^(DuplexModeDlg, 1)
DuplexModeValues= ^(DuplexModeDlg, 2)
NoList = ^(NoChoices, 1)
NoValues = ^(NoChoices, 2)
ShellCodeErrorTitle = "Error: "$(Function$(Option)Title)
ShellCodeErrorText = "Shell Code Error."
CANNOT_FIND_ANY_CARD = "Network card is not present in the system"
[DialogConstantsENG]
Help = "&Help"
Exit = "Cancel"
OK = "OK"
HelpContext = ""
Continue = "Continue"
Cancel = "Cancel"
[FileDependentDlgENG]
DlgText = "Choose the proper Duplex Mode from the list."$(!LF)+
" "
Combo1Label = " 10/100M Duplex Mode "
DlgTemplate = "ADAP_PROTO_COMBO"
DlgType = "Combination"
Caption = "Duplex mode "
Combo1List = $(DuplexModeList)
Combo1Out = $(DuplexModeValue)
ComboListItemsIn = {Combo1List}
ComboListItemsOut = {Combo1Out}
EditTextLim = ""
CBOptionsGreyed = {}
;HelpContext = 10
[DuplexModeDlg]
DuplexMode_0 = "(0) DEFAULT ", 0
DuplexMode_1 = "(1) AUTO ", 1
DuplexMode_2 = "(2) 10 Half Duplex", 2
DuplexMode_3 = "(3) 10 Full Duplex", 3
DuplexMode_4 = "(4) 100 Half Duplex", 4
DuplexMode_5 = "(5) 100 Full Duplex", 5
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.