Macronix International Co., Ltd.
Diagnostic program user's guide
=======================================
Copyright (C) 1998 by Macronix International Co., Ltd.
All rights reserved.
About mxdiag.exe
==================================================
This program is using for MX98713, MX98715, and MX98725 test.
Three sets of Vendor ID and Device ID will be searched automatically.
If the parameters of the current LanCard do not match one of them,
"Device not found" error message will be reported.
set1:
Vendor ID : 0x10d9
Device ID : 0x0531
set2:
Vendor ID : 0x10d9
Device ID : 0x0512
set3:
Vendor ID : 0x1011
Device ID : 0x0009
Contents of mxdiag.exe
==================================================
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Function Select ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³F1. Network Diagnose ³
³F2. PMAC Diagnose ³
³F3. EEPROM Access ³
³F4. PORT Selection ³
³F5. ACPI Diagnose ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
1.Network Diagnose
Four network diagnose functions are provided in this item .
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Network Diagnose ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ Ping-Pong Master Mode ³
³ Ping-Pong Slave Mode ³
³ External loopback ³
³ Internal loopback ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
1.1 Ping-Pong Master Mode:
This selection forces adapter to send out packets (random
packet length ) and wait for echo.
After receiving the echo, compare them and accumulate
the error status. To do this, a responcer is needed in
the network.
The packet size is a random number between 60 and 1514.
1.2 Ping-Pong Slave Mode:
As a network responcer, it echoes all received packets.
1.3 External loopback:
In this item, the test signal will be send out of chip MX987xx Family.
To do this test, an external loopback path should be provided.
The packet size is a random number between 60 and 1514.
1.4 Internal loopback:
Do an internal loopback test on MX987xx Family internal function.
The packet size is a random number between 60 and 1514.
2.PMAC Diagnose
This item do a basic function verification on MX987xx chips.
ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
º Function Test º
ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹
º Internal Loopback º
º ISR Test º
º CSR Test º
º EEPROM Test º
º Perfect Test º
º Inverse Test º
º Hash Test º
º HashOnly Test º
º Multi_PKT Test º
º Burst_Len Test º
ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ
Internal loopback : internal loopback test
ISR Test : interrupt service test
CSR Test : command and status register function test
EEPROM Test : EEPROM read/write test
Perfect Test : Perfect filtering function test
Inverse Test : Inverse filtering function test
Hash Test : Hash filtering function test
HashOnly Test : HashOnly filtering function test
Multi_PKT Test : One packet in multi-descriptor function test
Burst_Len Test : Burst length test
3. EEPROM Access
ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
º EEPROM Access º
ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹
º Dump EEPROM º
º Download EEPROM to C46.PKT º
ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ
3.1 Dump EEPROM:
Dump the content of EEPROM.
3.2 Download EEPROM to C46.PKT:
Write file c46.pkt by EEPROM value.
4. PORT Selection
MX98713 provides 2 kinds of signal interface ( 4B/5B ).
It depends on the hareware design, for 4B connection the
"MII PORT" should be selected, and for 5B connection select
item "SYMBOL PORT". The default selection is "SYMBOL PORT".
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ PORT SELECT ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ SYMBOL PORT ³
³ MII PORT ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
MX98715 and MX98725:
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ PORT SELECT ³
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
³ AutoSense ³
³ 100 Full_Dup ³
³ 100 Half_Dup ³
³ 10 Full_Dup ³
³ 10 Half_Dup ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
5. ACPI Diagnose
ÉÍÍÍÍÍÍÍ ACPI Test ÍÍÍÍÍÍÍÍÍ»
º PC to be waked up º
º PC to send magic packet º
ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ
In this item, it tests both of ACPI (Advence Configuration and Power
Interface) and WOL (Wake On LAN) functions. Two PCs is necessary to
execute this diagnostic function. When the PC runs "PC to be waked up"
funtion, the PC's MotherBoard must support ACPI and WOL. And the
standby power's current of ATX power supply requests least than 300mA.
The other PC that running "PC to send magic packet" will initiate
the wakeup function by sending the magic packet.
About "mxdiag eep"
=================================================
Type "mxdiag eep", it will write eeprom from c46.pkt.
About "mxdiag eep"
==================================================
Type "mxdiag eep", it turns out to be an EEPROM auto programming routine.
Before using this function, make sure that the content of EEPROM should
be all "0xff" ( a brand new EEPROM default value).
After executing "mxdiag eep", the following action will be taken:
1. Upload the content of file c46.pkt to the current EEPROM.
2. The CRC value will be calculated and programmed into EEPROM automatically.
3. The Network ID and Magic ID that defined in c46.pkt will be increased by 1.
According to "MX987xx EEPROM FORMAT" we get an example.
The contents of c46.pkt are:
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 01 01 00 00 12 34 56 78 00 00 12 34 03 00
1f 04 00 0b 8e 00 03 1b 6d 00 04 03 8e 00 05 1b
6d 00 00 00 00 00 00 00 00 00 56 78 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
14 00 00 00 00 00 00 00 00 00 12 05 d9 10 ab cd
After execute "mxdiag eep", the format show above will be programmed
into EEPROM. and the contents of c46.pkt turn out to be:
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 01 01 00 00 12 34 56 79 00 00 12 34 03 00
1f 04 00 0b 8e 00 03 1b 6d 00 04 03 8e 00 05 1b
6d 00 00 00 00 00 00 00 00 00 56 79 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
14 00 00 00 00 00 00 00 00 00 12 05 d9 10 ab cd
-- THE END --
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.