BOOT95.TXT Driver File Contents (Myson_NIC_Windows.zip)


How to install the Myson MTD80X based PCI adapter Boot Rom for Windows 95.


 1. What you will need?

    * A Windows NT 4.0 server with the Remoteboot Service installed and
      configured. Earlier versions of NT do not support Windows 95 clients.
    * A workstation running Windows 95 with connections to the NT server.
      This workstation should have a CD-ROM drive. If not, the NT server
      must have a CD-ROM drive installed and configured for sharing.
    * Windows 95 on CD-ROM. Make sure the CD-ROM contains the NETSETUP.EXE
      program. You must purchase the correct licensed copy of Windows 95 for
      network installation.
    * An Ethernet network adapter with boot PROM. You must be able to remoteboot
      from the NT server with this boot PROM.

 2. Installing the "Remoteboot Service" on the NT Server.

    a. Choose the Control Panel under the NT Server, and then select the
       network options.
    b. Add the DLC and NetBEUI protocol in the protocols, and you also
       need add the Remoteboot service in the services.
    c. During the installation, you need to put the NTAS CD disk into the
       CD-ROM.

 3. Sharing the directory \RPLFILES in the NT Server.

    Sharing the directory \WINNT\RPL\RPLFILES by using File Manger sharing.

 4. Copy all the MS-DOS 6.22 ver files to \WINNT\RPL\RPLFILES\BINFILES\DOS622

    For example:

        a. Make the DOS 6.22 Boot floppy disk.
        b. attrib -s -h a:\io.sys in the boot disk.
        c. attrib -s -h a:\msdos.sys in the boot disk.
        d. copy a:\io.sys \WINNT\RPL\RPLFILES\BINFILES\DOS622
        e. copy a:\msdos.sys \WINNT\RPL\RPLFILES\BINFILES\DOS622

 5. Creating DOS Remoteboot configuration for new adapter

    a. Copy the NDIS2(MTD80X.DOS) for the MTD80X Adapter to the
       "\WINNT\RPL\BBLOCK\NDIS"  directory.
    b. Create this directory \WINNT\RPL\BBLOCK\NETBEUI\MTD80X and
       then copy the W95BB.CNF, MTD80X.CNF and PROTOCOL.INI files to the
       directory.
    c. In MS-DOS Prompt type " NET START RemoteBoot ".
    d. Use RPLCMD utility to add a bblock record for new adapter.
    e. Screen will display under line option and you following these do it.

        Adapter Boot Config Profile Service Vendor Wksta [Quite] V
        Add Del Enum:A
        VendorName=004095       <Ether ID>
        VendorComment=MYSON for MTD80X

        Adapter Boot Config Profile Service Vendor Wksta [Quite] B
        Add Del Enum:A
        BootName=DOSMX
        VendorName=004095
        BbcFile=BBLOCK\NETBEUI\MTD80X\MTD80X.CNF
        BootCommet=MTD80X PCI Adapter   <Name of this adapter>
        WindowsSize=0

        Adapter Boot Config Profile Service Vendor Wksta [Quite] C
        Add Del Enum:A
        ConfigName=DOS622MX
        BootName=DOSMX
        DirName=DOS
        DirName2=DOS622
        FitShared=FITS\DOS622.FIT
        FitPersonal=FITS\DOS622P.FIT
        ConfigComment=DOS 6.22 for MTD80X PCI Adaper <Name of the Config>
        DirName3=
        DirName4=

        Adapter Boot Config Profile Service Vendor Wksta [Quite] Q

    f. Shutdown Windows NT server, and reboot it.

 6. Login Administrator to NTAS server.

 7. Starting Remoteboot service and Remoteboot Manager
    a. In MS-DOS Prompt type "NET START Remoteboot"
    b. In Network administrator, select Remoteboot Manager
       1.Choose Remoteboot, New Profile, created a MTD80X Profile Name
       2.Add new workstation for MTD80X Adapter and choose MTD80X Profile
         file.
    * Above will run on CLIENT. *
    c. Use Administrator enter WinNT
    d. Choose start --> Programs --> Administrative Tool --> Remote Manager
    e. Use Remoteboot item --> Covert Adapters


Installing Windows 95 for Windows 95 Clients

 1. What you will need?

    * Install Server-Based Setup (SBS) on a Window NT 4.0 server
    * Install the first Windows 95 client
    * Install subsequent clients

 2. Installing SBS for Windows 95 Clients

    a. On the Windows NT 4.0 server, create a shared directory (sbs) with
       90 MB space available, assign read-ponly for regular user and full
       access for administrator.
    b. Put the Windows 95 compact disc in the client's CD-ROM drive. In Windows
       Explorer, switch to the ADMIN\NETTOOLS\NETSETUP directory.
    c. Double-click NETSETUP.EXE.
       Note that you must run NETSETUP.EXE at a Windows 95 client. It will
       encounter errors on a computer running Windows NT.
    d. In the Server-Based Setup dialog box, click the Set Path button, and
       then specify the path to the SBS server. Then click OK.
       You can type a drive letter for a mapped drive, a network name for a
       server the format is: \\server1\sharedir,
       for example:
         \\ntserver\sbs
    e. Click Install. Server-Based Setup presents a series of dialog boxes so
       that you can complete these actions:
       * Specify an "install policy" for how users can install Windows 95 from
         the server. If you support only remoteboot clients, choose the
         "Server" option. If you support other SBS functions as well, choose
         "User's choice." Do not choose "Local hard drive."
       * Set the source path for Windows 95 files. This is the path to the
         compact disc on the client.
       * If asked, specify that you do NT remoteboot installation require
         special settings.  not want to create a default setup script. Setup
         scripts for Windows
       * Provide a CD Key number for product identification. Server-Based Setup
         copies Windows 95 files to the SBS shared directory.
    f. At the remoteboot server, put the compact disc or floppy disk
       containing the Windows NT remoteboot for Windows 95 files into a drive.
       Change to the drive and then change to the UPDATE\WIN95 or
       CLIENTS\RPL\UPDATE\WIN95 directory.
    g. Run win95srv.bat to update the Windows 95 files for remotebooting.
       For example:
         cd\clients\rpl\update\win95
         win95srv.bat \\ntserver\sbs
    h. At the remoteboot server, start Remoteboot Manager. From the Configure
       menu, choose Check Configurations to activate the new configurations.

 3. Installing the First Windows 95 Client

    . Overview
      Installing the first Windows 95 client requires booting that client
      first to MS-DOS 6.2x, running Windows 95 Setup on the client, and then
      copying selected files from the client's machine directory to the
      remoteboot server. Once you have installed this first client, you can
      easily install subsequent clients by using SBS to make a modified copy
      of the original machine directory without having to run Windows 95 Setup
      again. Your first Windows 95 clients must be using an ethernet network
      adapter. Furthermore, the first client computer must have one or more
      PCI slots for later use with the PCI network adapter.

      Each remoteboot client has a "machine directory," a directory on a
      server that contains client-specific configuration information and data.
      For example, the machine directory contains the following:
        * Appropriate initialization and configuration files (including
          WIN.INI and SYSTEM.INI) SYSTEM.DAT and USER.DAT (the Registry)
        * Files that define the Desktop, Start menu directories, and other
          programs
        * The spool directory for printing
        * The swap file and TEMP directory
    . Create "machine0" directory on the windows NT server.
    . Boot the new client to MS-DOS 6.22.
    . Use the "net use" command to map drive letters to the SBS server and
      machine0 directory location, it will run on CLIENT.
      For example:
               net use f: \\ntserver\sbs
               net use g: \\ntserver\machine0
    . Change to the drive letter mapped to the SBS directory.
    . Run the Windows 95 Setup program by typing
               setup /t:temppath
      where /t: is required and temppath is a path to a directory in which to
      store temporary files during installation. For example, if G: is mapped
      to the shared directory containing the client's machine directory, you
      could type
               f:
               setup /t:g:\client.tmp /im /is
      to store temporary files on that server.
      * Do not delete the t:\temppath directory until you have completed
        steps.
      * If you are installing two Windows 95 clients simultaneously (for
        example, to support clients with different network adapters), choose
        separate temporary directories for each client.
    . Make the following decisions during setup:
      * In the Server-based Setup dialog box, choose "Set up Windows to run
        from a network server" if asked.
      * In the Startup Method dialog box, choose "Start Windows from the
        network (remote boot server)."
      * In the Machine Directory dialog box, when asked where to install
        Windows 95, type the path of the machine directory (using the drive
        letter specified in Step 4, for example, g:\client).
      * In the Setup Options dialog box, choose Custom setup.
      * In the Analyzing Your Computer dialog box, choose "No, I want to
        modify the hardware list." Exclude as many hardware types and items
        from autodetection as possible. If autodetection crashes, run Setup
        again and exclude more items from autodetection. One problem could be
        that your network adapter is on IRQ2 or IRQ3; this conflicts with
        serial port detection with some network adapters.
      * In the Select Components dialog box, clear "Communications" the
        checkbox.
      * add a network component from a floopy disk.
      * In the Network Configuration check that your network adapter and
        desired protocols are present and configured correctly. If there are
        no network adapters shown, you must add and configure your network
        adapter. If youadd your network adapter, you must confirm the resource
        settings for theadapter. Select the adapter name in the Network
        Configuration dialog box, click Properties, and then click the
        Resources tab. Check that the settings displayed are correct (for
        example, the interrupt level). Then, click OK to force the Setup
        program to accept the settings; do not click Cancel. For details about
        protocols on Windows 95 remoteboot clients, see "Supporting Other
        Protocols", later in this chapter.
      * In the Identification dialog box, make sure that the workgroup for
        this client is the same as the workgroup or domain of the SBS server
        and machine directory server.
    . When the Windows 95 Setup program is done, reboot the client. The
      client will not yet boot to Windows 95. You must complete more steps
      first.
    . At the remoteboot server (or a client running Remoteboot Manager
      focused on the remoteboot server), start Remoteboot Manager.
    . Create a profile for the Windows 95 client. In the Configuration box,
      choose the Windows 95 configuration corresponding to the client's
      network adapter type.
    . If you are not sure which configuration to choose, check the profile
      that is currently associated with this client for booting MS-DOS, and
      use the equivalent Windows 95 profile.
    . Edit the client's workstation record to assign the client to the
      Windows 95 profile.
    . Copy mtd80x.dos to c:\machine0\client\suboot directory.
      Copy mtd80x.sys and ndis.vxd files to c:\sbs\system directory.
      * You can find these files from \BOOTROM\RPL\NTRPL\Win95 directory.
    . Next, you can find the following files in the c:\machine0\client\suboot
      directory
        * AUTOEXEC.BAT
        * CONFIG.SYS
        * MSDOS.SYS
        * PROTOCOL.INI
        * MTD80X.DOS
        * SYSTEM.DAT
    . Creates sample boot block records for Windows 95. The sequence commands
      are:
        c:\winnt\rpl>rplcmd

            Adapter Boot Config Profile Service Vendor Wksta [Quite] B
            Add Del Enum:A
            BootName=W95XX
            VendorName=004095
            BbcFile=BBLOCK\NETBEUI\MTD80X\W95BB.CNF
            BootCommet=MTD80X PCI Adapter FOR WIN95 <Name of this adapter>
            WindowsSize=0

            Adapter Boot Config Profile Service Vendor Wksta [Quite] C
            Add Del Enum:A
            ConfigName=W95MTD80X
            BootName=W95XX
            DirName=DOS
            DirName2=WIN95
            FitShared=FITS\WIN95.FIT
            FitPersonal=FITS\WIN95P.FIT
            ConfigComment=WIN95 for MTD80X PCI Adaper <Name of the Config>
            DirName3=
            DirName4=

            Adapter Boot Config Profile Service Vendor Wksta [Quite] Q

    . At the Remoteboot Server (or a client running Remoteboot Manager
      focused on the remoteboot server), start Remoteboot Manager.
    . Create a profile (WMTD80X) for the Windows 95 client. In the
      Configuration box, choose the Windows 95 configuration corresponding
      to the client's network adapter type.
    . If you are not sure which configuration to choose, check the profile
      that is currently associated with this client for booting MS-DOS, and
      use the equivalent Windows 95 profile.
    . Edit the client's workstation record to assign the client to the
      Windows 95 profile.(In the SBS server of the MACHINES.INI file.)
    . At the remoteboot server (or a client with write access to the
      remoteboot server's RPL directory), run the RPL\BIN\WIN95CLT.BAT program
      by typing:
        cd winnt\rpl\bin
        win95clt mach_directory \\rpl_server profile_name
      where
        * mach_directory is the path to the client's machine directory.
        * \\rpl_server is the name of the remoteboot server.
        * profile_name is the name of the Windows 95 profile associated with
          the client.
      For example, you could type:
        cd \winnt\rpl\bin
        win95clt \\ntserver\machine0\client \\ntserver wmtd80x
    . The WIN95CLT program copies client-specific Windows 95 real-mode (also
      identified as MS-DOS 7.0) boot files from the client's machine directory
      to the RPL\RPLFILES\PROFILES\<profile_name>\SUBOOT directory on the
      remoteboot server.
    . At the SBS server (or a client with write access to the SBS directory),
      edit the MACHINES.INI file in the SBS directory. Add the following lines
      for the new client:
        [adapter id]
        SYSDATPATH=g:\machine_dir
        g=\\mach_server\mach_share
      where:
        * adapter id is the network adapter id, specified in the remoteboot
          workstation record for this client.
        * \machine_dir is the location of the client's machine directory on a
          server. “g?is the drive letter assigned on the next line to the
          shared directory where the client's machine directory is located.
        * \\mach_server\mach_share identifies the drive letter assigned to the
          shared directory where the machine directory resides. You must use
          the same drive letter and share name established in Step 4.
      For example, you might add the following lines to MACHINES.INI:
        [00409500002b]
        SYSDATPATH=g:\client
        g=\\ntserver\machine0
    . Power off the machine and remove the ethernet network adapter.
    . Install the BootWare ROM on the PCI adapter.
    . Configure the ROM to use the RPL boot protocol.
    . Reboot the Windows 95 client.
    . Start Remoteboot Manager on the server.
    . Remember to log on to a user account that belongs to the Administrators
      local group.
    . Start the remoteboot client. The client does not actually boot, but it
      does send a boot request to the server.
    . In Remoteboot Manager on the server, from the View menu, choose
      Refresh.
    . In Remoteboot Manager, select the adapter record that has appeared
      with the network adapter ID number in place of the client name. From the
      Remoteboot menu, choose Convert Adapters.
    . In the Wksta Name box, type a name for the client. The name can have no
      more than 15 characters [with no spaces or backslashes (\)]. The
      Remoteboot Service will create a Windows NT user account with this name,
      not for the user but for the client itself.
    . The client will now boot to Windows 95 and complete the Windows 95
      setup.

Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web2, load: 1.32