1. 7900a.zip Driver
2. WIN95.TXT File Contents

WIN95.TXT Driver File Contents (7900a.zip)

\HELP\WIN95_98\WIN95.TXT

                        Fast Ethernet PCI Adapter
                 ---------------------------------------------
                  Driver Installation for Microsoft Windows 95
                  --------------------------------------------

  Getting Started
  ---------------
  Microsoft Windows 95 does not come bundled with the driver for the
  adapter.  You must go through the following procedure to
  install the device driver into the Windows 95 system for the adapter 
  to function properly.

  The Windows 95 CD is needed to complete this installation.

  The following example illustrates the installation of the Adapter.

  Windows 95OSR2 Installation Procedure
  --------------------------------------
  It is recommended that you complete the Windows 95 installation prior to
  installing the adapter card.

  1.  Shut down the computer and install the adapter into the the PCI 
      slot.
      
  2.  Start your Windows 95 system normally.

      Upon power up, the system will indicate to you that a new PCI
      Ethernet Controller has been found.

  3.  Insert the Installation CD-ROM and click "Next".
      It appear "windows found the following updated driver for this device"

      *** Please,Click"Other locations" ***
      
  4.  It appear "type the name of the folder that contains the driver you want"
      Please,input " D:\win95" on space 

      Then,Click "OK"
           Click "Finish".

  5.  Click on OK when asked to insert the Installation CD-ROM labeled
      "U.S. Robotics 10/100 PCI NIC TX Disk". 
    
      The Installation CD-ROM should still be in the drive since we haven't removed
      it.

  6.  Enter "D:\Win95" and click on OK when prompted for the location of the
      "USR79N3.SYS" file.

      Windows 95 will search into the Installation CD-ROM for the USR79N3.SYS
      file.

  7. Click on Yes when asked if we want to restart the system.


  8. Remove the Installation CD-ROM when the system
      reboots.
 
 
  Windows 95 Installation Procedure
  --------------------------------------
  It is recommended that you complete the Windows 95 installation prior to
  installing the adapter card.

  1.  Shut down the computer and install the adapter into the the PCI
      slot.
      
  2.  Start your Windows 95 system normally.

      Upon power up, the system will indicate to you that New Hardware Found 
      Table choice " Driver from disk provided by hardware manufacture".

  3.  Insert the Installation CD-ROM and click "OK".

  4.  Enter "D:\win95" and click on OK 

      Windows 95 will search into the Installation CD-ROM for the USR79N3.SYS
      file.

  5. Click on Yes when asked if we want to restart the system.

  6. Remove the Installation CD-ROM when the system
      reboots.

  Advanced Setup
  --------------
  The driver configures the adapter card to operate in autosensing
  mode by default.  In this mode, the card automatically selects the most
  appropriate operating speed and duplex mode.  There might be instances
  when you need to configure the adapter card to operate at a particular
  speed and duplex mode.  The following procedure guides you into the
  Windows 95 system for this setting.

  1.  In Control Panel, open "Network".

  2.  Click on the "U.S. Robotics 10/100 PCI NIC TX" selection.  
      Then, click on the "Properties" button.

  3.  Click on the "Advanced" memu tab in the adapter card window.

  4.  Click on the "Link Speed/Duplex Mode" property selection.

  5.  The "Link Speed/Duplex Mode" windows will show the following possible 
      selections:

         Auto Mode
        10Half Mode                       
        10Full Mode
        100Half Mode                      
        100Full Mode
         
      Choose the appropriate setting as needed.


  

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

• Expand the archive file (if the download file is in zip or rar format).

• If the expanded file has an .exe extension, double click it and follow the installation instructions.

• Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

• Find the device and model you want to update in the device list.

• Double-click on it to open the Properties dialog box.

• From the Properties dialog box, select the Driver tab.

• Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.