README.TXT Driver File Contents (56t_1101.zip)

DME560T Ethernet/Fax/Modem                                         May 1996

			  Manual Update Supplement
	
			     !!!!!!Note!!!!!!!

  For a quick start simply run INSTALL.EXE on the root of this Driver disk.

			     !!!!!!!!!!!!!!!!!

This document contains information that supplements the "User's Manual"
and accompanying software. The User's Manual can be found in the root of the
driver disk as MANUAL.TXT.

  Contents
  ÄÄÄÄÄÄÄÄ
	Introduction
	PCMCIA Driver Installation
	Getting Started
        EMM386 Usage with DME560T
	Driver Directory Structure
	Support Options
	Copyrights, Trademarks, and Disclaimers

  Introduction
  ÄÄÄÄÄÄÄÄÄÄÄÄ
        Thank you for purchasing the DME560T Ethernet/Fax/Modem PC Card.
        This diskette has network driver support for the DME560T
	Ethernet/Fax/Modem PC Card. There is a format change for this driver
	disk. All README's have been reformatted, an easy setup program,
	and consistency on all documentation provided.

	We hope our new readme's and installation will minimize the users
	effort to make our products work. Should you have further
	recommendations please contact the support manager.

  Install PC Card Software Manually
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
	The installation software has been carefully designed to detect
	a combination of hardware and software installed on the PC. Proper
	detection will allow the PC's PC Card drivers to enable the
        DME560T. If the installation software fails to complete,
	the enabler will need to be manually copied from the driver disk
	to the PC. The follow the next few steps for instructions
		 
        If Windows for Workgroup 3.11, Windows NT, Windows 95, or Windows 98
         are used, follow the instructions for installing PC Cards in the
         PC's manual.

	Determine if any third party generic enablers installed on the PC.                                 
	 These are identified by a search through the CONFIG.SYS file for
	 the following lines:

	     Vendor           Device Loaded in CONFIG.SYS
	     ---------------  -------------------------------
	     Awards Software  DEVICE=C:\CARDWARE\PCENABLE.EXE
	     System Soft      DEVICE=C:\CARDSOFT\CARDID.EXE
	     Phoenix          DEVICE=C:\PCMPLUS\PCMSCD.EXE

	 If one of these exist in your CONFIG.SYS, it can be used to enable
         the DME560T Ethernet/Fax/Modem PC Card.  Follow the PCMCIA driver
	 installation instructions in the PC's manual.

	If the PC Card drivers do not support multi-function cards, please
	 use the included enabler.

	    Disable all current PC Card drivers by editing the CONFIG.SYS
	     and AUTOEXEC.BAT. If it is necessary to keep these drivers
	     for other adapters skip to next section. 
	    Insert Driver Disk in drive A:.
	    Type C: at the command prompt.
	    Type MD DMECARD to make a new directory.
	    Type COPY A:\ENABLER\*.* C:\DMECARD to copy the enabler to
	     your directory.
	    Modify the PATH= statement in your AUTOEXEC.BAT to include
	     path C:\DMECARD.
	    
	     Change From  PATH=<Original Path>
		    To    PATH=<Original Path>;C:\DMECARD

        Use the CARDEN.EXE to enable DME560T when the PC is loading
	 Card Services.

  Getting Started
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
	For Novell, Lan Manager, and Packet Driver, first insert the
         DME560T Ethernet/Fax/Modem PC Card into one of the free PCMCIA
	 card slots, remove all other PC Cards from your machine.
	
        Then insert the "DME560T Drivers Disk" into drive A, and type
	 A:\INSTALL at the command prompt.  The installation program
	 will copy files to the destination directory and modify your
	 related files(CONFIG.SYS, AUTOEXEC.BAT, and NET.CFG).

        For Windows for Workgroup, Windows NT ,Windows 95 & Windows 98 use the
         "Network Setup" utility provided by windows system to install
         the DME560T. On this disk you will find sub-directories for each of
	 the Microsoft products. Each directory has a README.TXT that will
	 help install that particular Microsoft product.

        After installation, simply reboot the machine to enable the DME560T.
  

  EMM386 Usage with DME560T
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
	Under PCMCIA all I/O cards (including Ethernet and Modem) must
	be initialized as memory cards and then switched into I/O mode
	operation by an enabler software.

	Therefore, the enabler software (such as CARDEN.EXE) must see the
	PC Card memory when it is executed.  DOS extended memory managers
	such as EMM386 and QEMM take control of the PC memory space which
	effects PC Card initialization.

	There are two solutions available:

	    1) Run enabler (CARDEN or existing PC Card drivers + CARDEN)
	       before EMM386 or QEMM is loaded.

	    2) Exclude at least 4K of memory from EMM386's or QEMM's use.
	       An exclusion of X=D000-D3FF will work well.There may also
	       be additional exclusions for your PCMCIA drivers, don't 
	       modify these.

  Driver Directory Structure
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
	The network drivers on this disk is organized in the following
	structure. Each directory contains a README.TXT file which
	provides you with detailed installation instructions for drivers
	in that directory:

  DME560T Diskette Release 05/01/96
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
	CARDEN.EXE    Direct PCMCIA Card Enabler for DOS, supports
                      DME560T and Intel compatible, Compaq and Databook
		      controllers.
        LMODI.COM   DME560T DOS/ODI Driver working with direct enabler(LAN
		      & MODEM run concurrently). Supports Intel compatible,
		      Compaq and Databook controllers.
        LMNDIS.DOS   DME560T DOS real mode NDIS Driver
        LMPD.COM    DME560T DOS real mode Packet Driver
        LMNDIS.386   DME560T Enhance Mode NDIS Driver for Win for Workgroups
        LMNDIS.SYS    LanModem Enhance Mode NDIS Driver for Windows 95 & 98.
        LMNDIS.SYS   DME560T Enhance Mode NDIS Driver for Windows NT.

  Support Options
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
	We are consistently improving and upgrading our drivers. you are
	welcomed at any time to browse through our BBS, and download any
	drivers, utilities and help files.

        If you still cannot get the DME560T working properly, our
	technical experts are always ready to help.  Please be at your
        computer, have your DME560T, Drivers Disk, and the following
	information available:

	* Version number of CARDEN.EXE and any drivers you are running
	* The extact text of any error message displayed on your screen
	* The type of computer
	* The type of network

	For technical support, you may contact your authorized D-Link 
	distributor, dealer, or the following D-Link headquarters:

        In U.S.A.           Tel: +1(949)455-1688      Fax: +1(949)455-2521
                            BBS: +1(949)455-1779      BBS: +1(949)455-9616

	In Canada           Tel: +1(905)828-0260      Fax: +1(905)828-5669
			    BBS: +1(905)828-6673

	In U.K. & Europe    Tel: +44(181)235-5555     Fax: +44(181)235-5500
			    BBS: +44(181)235-5511

	In Germany          Tel: +49(6196)643011      Fax: +49(6196)28049
			    BBS: +49(6196)28378

	In Asia, Taiwan     Tel: +886(2)916-1600      Fax: +886(2)914-6299
			    BBS: +886(2)910-1835

	In France           Tel: +33(1)30238688       Fax: +33(1)3028689

	In Australia        Tel: +61(2)4177100        Fax: +61(2)4171077
			    BBS: +61(2)4173711

	In Nordic           Tel: +46(40)163330        Fax: +46(40)163340
			    BBS: +46(40)163343

	In Singapore        Tel: +657746233           Fax: +657746322
			    BBS: +657744787

	In China            Tel: +86(10)4934175       Fax: +86(10)4991648

	In Tokyo            Tel: +81(3)57512351       Fax: +81(3)57512352

	In India            Tel: +91(22)6172478       Fax: +91(22)6172476

	The BBS communication setup information is as follows :
	     Speed:  2400-14400 baud                           - Germany
		     2400-9600 baud                            - Asia,Taiwan
		     14400-16800 baud                          - Canada
		     9600-14400 baud V32, V32bis, V42, V42bis  - U.S.A.
		     2400-19200 baud V24, V32, V32bis, V42bis  - U.K. & Europe
	     Parity: None
	  Data bits: 8
	  Stop bit : 1

  Copyrights, Trademarks, and Disclaimers
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
    All references to MS, Windows, Win95, Windows 95, Windows 98, Windows NT,
    WinNT are rights reserved by Microsoft Corporation

    All references to Nvl., ODI, Netware, NW, IPX, IPXODI, and LSL are
    rights reserved by Novell Corporation

    Further rights reserved to their respective corporations
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web1, load: 1.44