README.TXT Driver File Contents (56t_1101.zip)

DME560T Ethernet/Fax/Modem                                          May 1996

		       Lantastic AI V. 5.x & 6.x

  Contents
  ÄÄÄÄÄÄÄÄ
	Introduction
	Getting Started
	Support Options
	Copyrights, Trademarks, and Disclaimers


  Introduction
  ÄÄÄÄÄÄÄÄÄÄÄÄ
        This installation assumes that the DME560T adapter is working
	properly. Please consult \README.TXT for help with the adapter
	set-up. Getting Started will describe the installation instructions.

  Getting Started
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
    Lantastic AI 5.0 Install
    ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 
	 Using NDIS driver
	 ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
         For Lantastic 5.0 the DME560T uses the NDIS 2.0 driver.
         Users can replace AEXNDIS.DOS with "LMNDIS.DOS" allowing
	  
	 Install Lantastic AI 5.0, during the installation select
	  the Artisoft AE2 NDIS driver (AEXNDIS.DOS).

	 Edit the system's C:\CONFIG.SYS and make the following changes.

	 CONFIG.SYS
	 ÄÄÄÄÄÄÄÄÄÄ

	      DEVICE=C:\LANTASTI\PROTMAN.DOS /I:C:\LANTASTI
	      DEVICE=C:\LANTASTI\AEXNDIS.DOS     -------> By Artisoft
	      
	      * please replace to *
	      
              DEVICE=C:\LANTASTI\LMNDIS.DOS    -------> By DME560T

	 Edit the system's C:\LANTASTI\STARTNET.SYS and make the
	  following changes.

	 ÉÍNoteÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
	 º                                                        º
	 º  If you are using PROTMAN.DOS V1.x, you must use the   º
	 º  NO_BIND option on the AI-NDIS command line in the     º
	 º  STARTNET.BAT, and you must run NETBIND.EXE V1.x       º
	 º  before AILANBIO.EXE.                                  º
	 º                                                        º
	 ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

	 STARTNET.BAT
	 ÄÄÄÄÄÄÄÄÄÄÄÄ

	      C:\LANTASTI\AI-NDIS BIND_TO=AEXNDIS_NIF
	      
	      * please replace to *
	      
              C:\LANTASTI\AI-NDIS BIND_TO=LMNDIS_NIF


	 Edit the system's C:\LANTASTI\PROTOCOL.INI and make the
	  following changes.

	 PROTOCOL.INI
	 ÄÄÄÄÄÄÄÄÄÄÄÄ
	      [AEXNDIS_NIF]
		 DRIVERNAME = AEXNDIS$
	      
	      * please replace to *
	      
              [LMNDIS_NIF]
                 DRIVERNAME = LMNDIS$


    Lantastic 6.0 Install
    ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 
	 New Installation
	 ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

         To install D-Link NDIS driver "LMNDIS.DOS",
	      -Install Lantastic
	      -Select "NDIS support for network adapters"
              -Insert the DME560T Driver Disk into Drive A:
	      -The install program will ask for the driver path,
	       type the path "A:\LANTASTI".
              -Install program will load, "LMNDIS.DOS" and "PROTOCOL.INI",
	       to target directory.

	 Existing Installation
	 ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
         For Lantastic 6.x the DME560T uses the NDIS 2.0 driver.
         Users can replace AEXNDIS.DOS with "LMNDIS.DOS" allowing

	 Edit the system's C:\CONFIG.SYS and make the following changes.

	 CONFIG.SYS
	 ÄÄÄÄÄÄÄÄÄÄ
	      DEVICE=C:\LANTASTI\AEXNDIS.DOS   -------> By Artisoft
	      
	      * please replace to *
	      
              DEVICE=C:\LANTASTI\LMNDIS.DOS  -------> By DME560T

	 Edit the system's C:\LANTASTI\STARTNET.SYS and make the
	  following changes.

	 STARTNET.BAT
	 ÄÄÄÄÄÄÄÄÄÄÄÄ
	      AI-NDIS BIND_TO=AEXNDIS_NIF
	      
	      * please replace to *
	      
              AI-NDIS BIND_TO=LMNDIS_NIF

	 Edit the system's C:\LANTASTI\PROTOCOL.INI and make the
	  following changes.

	 PROTOCOL.INI
	 ÄÄÄÄÄÄÄÄÄÄÄÄ
	      [NETBEUI_XIF]
	      DriverName = netbeui$
	      Sessions = 6
	      NCBS = 12
	      -------------------------------------------------------
	      Bindings = AEXNDIS_NIF  -----> By Artisoft
	      
	      * please replace to *
	      
              Bindings = LMNDIS_NIF -----> By DME560T
	      -------------------------------------------------------
	      LANABASE = 1
	      -------------------------------------------------------
	      [AEXNDIS_NIF]
	      DRIVERNAME = AEXNDIS$  -----> By Artisoft
	      
	      * please replace to *
	      
              [LMNDIS_NIF]
              DRIVERNAME = LMNDIS$  -----> By DME560T
	      -------------------------------------------------------
	      
	 Using ODI DOS driver
	 ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
         Users can use "LMODI.COM" driver to replace NRODI.COM
	  Artisoft's which is the ODI for DOS driver.

	 Install Lantastic AI 5.0, during the installation select
	  the Artisoft Node Runner ODI  driver (NRODI.COM).

	 ÉÍÍNoteÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
         º    The LMODI.COM following HSM v4.0 spec, please        º
	 º    backup LSL.COM, IPXODI.COM that were installed with    º
         º    Lantastic. Copy both drivers for the DME560T driver   º
	 º    disk A:\LANTASTI\LSL.COM, IPXODI.COM to c:\LANTASTI.   º
	 ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

	 Edit the system's C:\LANTASTI\STARTNET.SYS and make the
	  following changes.

	 STARTNET.BAT
	 ÄÄÄÄÄÄÄÄÄÄÄÄ
	      @echo ===== Begin Lantastic configuration =====
	      SET LAN_CFG=C:\LANTASTI
	      PATH C:\LANTASTI;%PATH%
	      SET LAN_DIR=C:\LANTASTI.NET
	      SET NWDBPATH=C:\Lantasti\NW
	      
	      LSL        --> Please use release driver diskette
              NRODI      --> Please replace with LMODI
	      ODINSUP
	      IPXODI     --> Please use release driver diskette
	      
	      ------------------------------------------------------
	      AI-NDIS BIND_TO=NRODI   -----> By Artisoft
	      
	      * please replace to *
	      
              AI-NDIS BIND_TO=LMODI -----> By DME560T
	      ------------------------------------------------------
	      AILANBIO @STARTNET.CFG
	      REDIR  LANTA @STARTNET.CFG
	      SERVER C:\LANTASTI.NET @STARTNET.CFG
	      NET LOGIN \\LANTA
	      @echo ===== End LANtastic configuration =====

	 Edit the system's C:\LANTASTI\NET.CFG and make the
	  following changes.

	 NET.CFG
	 ÄÄÄÄÄÄÄ
	 Please add the following lines to the NET.CFG file.

              Link Driver LMODI
		   Frame Ethernet_802.3

  Support Options
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
	We are consistently improving and upgrading our drivers. you are
	welcomed at any time to browse through our BBS, and download any
	drivers, utilities and help files.

        If you still cannot get the DME560T working properly, our
	technical experts are always ready to help.  Please be at your
        computer, have your DME560T, Drivers Disk, and the following
	information available:

	* Version number of CARDEN.EXE and any drivers you are running
	* The extact text of any error message displayed on your screen
	* The type of computer
	* The type of network

	For technical support, you may contact your authorized D-Link 
	distributor, dealer, or the following D-Link headquarters:

        In U.S.A.           Tel: +1(949)455-1688      Fax: +1(949)455-2521
                            BBS: +1(949)455-1779      BBS: +1(949)455-9616

	In Canada           Tel: +1(905)828-0260      Fax: +1(905)828-5669
			    BBS: +1(905)828-6673

	In U.K. & Europe    Tel: +44(181)235-5555     Fax: +44(181)235-5500
			    BBS: +44(181)235-5511

	In Germany          Tel: +49(6196)643011      Fax: +49(6196)28049
			    BBS: +49(6196)28378

	In Asia, Taiwan     Tel: +886(2)916-1600      Fax: +886(2)914-6299
			    BBS: +886(2)910-1835

	In France           Tel: +33(1)30238688       Fax: +33(1)3028689

	In Australia        Tel: +61(2)4177100        Fax: +61(2)4171077
			    BBS: +61(2)4173711

	In Nordic           Tel: +46(40)163330        Fax: +46(40)163340
			    BBS: +46(40)163343

	In Singapore        Tel: +657746233           Fax: +657746322
			    BBS: +657744787

	In China            Tel: +86(10)4934175       Fax: +86(10)4991648

	In Tokyo            Tel: +81(3)57512351       Fax: +81(3)57512352

	In India            Tel: +91(22)6172478       Fax: +91(22)6172476

	The BBS communication setup information is as follows :
	     Speed:  2400-14400 baud                           - Germany
		     2400-9600 baud                            - Asia,Taiwan
		     14400-16800 baud                          - Canada
		     9600-14400 baud V32, V32bis, V42, V42bis  - U.S.A.
		     2400-19200 baud V24, V32, V32bis, V42bis  - U.K. & Europe
	     Parity: None
	  Data bits: 8
	  Stop bit : 1

  Copyrights, Trademarks, and Disclaimers
  ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
  All documents and DME560T drivers are Copywritten to
  Copyright (c) 1996 by D-Link Corporation. All rights reserved.

  All references to MS, Windows, Win95, Windows 95, Windows NT, WinNT are
  rights reserved by Microsoft Corporation

  All references to Nvl., ODI, Netware, NW, IPX, IPXODI, and LSL are rights
  reserved by Novell Corporation

  Further rights reserved to their respective corporations
Download Driver Pack

How To Update Drivers Manually

After your driver has been downloaded, follow these simple steps to install it.

  • Expand the archive file (if the download file is in zip or rar format).

  • If the expanded file has an .exe extension, double click it and follow the installation instructions.

  • Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.

  • Find the device and model you want to update in the device list.

  • Double-click on it to open the Properties dialog box.

  • From the Properties dialog box, select the Driver tab.

  • Click the Update Driver button, then follow the instructions.

Very important: You must reboot your system to ensure that any driver updates have taken effect.

For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.

server: web1, load: 0.60