----------------------------------------------------------------------------
Installing the NetWare 3/4 ODI Server Driver on NetWare 4 Servers
----------------------------------------------------------------------------
The \NOVELL\SRVODI subdirectory contains the following files:
README.TXT - This file.
EWRK3.LAN - Novell NetWare 3/4 ODI Server Driver for the
DEC EtherWORKS 3 Ethernet Controller (v2.11).
EWRK3.LDI - Driver installation file used by NetWare 4 installation
utility (INSTALL.NLM) to install and configure the
NetWare 3/4 ODI Server Driver in that environment.
This is the same file as A:\EWRK3.LDI.
MSM.NLM - Novell supplied MSM module (V2.50)
ETHERTSM.NLM - Novell supplied TSM module (V2.50)
The \NOVELL\SRVODI subdirectory contains the following subdirectory:
\3_X - Files for installing and configuring the NetWare 3/4
ODI Server Driver in NetWare 3 servers.
Product Requirements:
Oper. Sys. - Novell NetWare 3.11, 3.12, 4.0, 4.01, 4.02
***TRADEMARKS***
DEC, Digital, DECpc, and AXP are registered trademarks of Digital
Equipment Corporation.
Novell, NetWare, and LAN WorkPlace are registered trademarks and NetWare
Loadable Module and NLM are trademarks of Novell, Incorporated.
Section 1 INSTALLING THE NETWARE 3/4 ODI SERVER DRIVER
------------------------------------------------------------
You can install and use the NetWare 3/4 ODI server driver on
NetWare 3 and NetWare 4 servers. The installation procedures
are different for each server.
To install the NetWare 3/4 ODI server driver on a NetWare 3
file server, follow the instructions in the README.TXT file located
in the \3_X directory.
To install the NetWare 3/4 ODI server driver on a NetWare 4 file
server, perform the following steps:
I. Verify that the network interface card (NIC) is properly
configured and installed. Refer to "DEC EtherWORKS 3 Owners Manual"
for instructions.
II. Perform the following steps to install the NetWare 3/4 ODI server
driver to the server NetWare partition and to configure and load the
driver:
A. Reload the INSTALL utility.
1. From the System Console, load INSTALL:
:LOAD INSTALL
2. Select "Maintenance/Selective Install" then "LAN Driver Options"
under "Installation Options."
3. Hit the Insert <Ins> key to select the "Load a LAN driver not
listed" option.
Note: 4.01 installs require you to Press F3 and enter the
path: "A:\NOVELL\SRVODI"
4. Place the Driver Distribution Diskette into the server floppy
drive then press RETURN to scan for NetWare 3/4 ODI server
drivers.
5. When "DEC EtherWORKS 3 Novell NetWare Server Driver"
appears, press RETURN and follow the instructions to install
the driver files.
B. From the "Driver EWRK3 parameters" option screen, configure the I/O
port address, node address, and frame types.
1. Enter the port address where the DEC EtherWORKS 3 controller was
configured via the NICSETUP utility.
2. Enter an optional node address override in canonical-format.
If you enter a node address override, that address is added to
the driver configuration table and used as a source address on
all transmitted frames for that controller.
3. Edit the frame type by pressing the ENTER key when "ETHERNET 802.2"
is highlighted. Use the ENTER and F3 keys to load either one or
all of the supported Ethernet frame types. If a frame type is not
specified, the default frame type, ETHERNET_802.2, is used.
4. Press the F10 key to load the driver. If the driver does not
load, use the Alt-Esc key sequence to switch to the System
Console and view the driver load error message.
5. If the driver loaded successfully, the INSTALL utility asks
whether IPX should be bound to the driver and prompts for a
proper external IPX address. Follow the utility instructions
to continue, then return to the "Installation Options" menu.
6. To save the configuration information, select "NCF Files Options"
then "Create AUTOEXEC.NCF file" to add the driver LOAD and BIND
statements to the AUTOEXEC.NCF file. The next time the server is
restarted the driver loads and binds to IPX automatically.
7. Exit the INSTALL utility, DOWN the server, and return to the DOS
prompt.
III. Follow the instructions in the "EtherWORKS 3 Owners Manual" for
connecting the controller to the ethernet network.
IV. Restart the server with the NetWare 3/4 ODI server driver.
Enter the following command at the DOS prompt:
SERVER
The changes made to the AUTOEXEC.NCF file, in the steps above,
will now take effect.
Download Driver Pack
After your driver has been downloaded, follow these simple steps to install it.
Expand the archive file (if the download file is in zip or rar format).
If the expanded file has an .exe extension, double click it and follow the installation instructions.
Otherwise, open Device Manager by right-clicking the Start menu and selecting Device Manager.
Find the device and model you want to update in the device list.
Double-click on it to open the Properties dialog box.
From the Properties dialog box, select the Driver tab.
Click the Update Driver button, then follow the instructions.
Very important: You must reboot your system to ensure that any driver updates have taken effect.
For more help, visit our Driver Support section for step-by-step videos on how to install drivers for every file type.