RL2000A.PCI/NDIS2/NDIS2.TXT Driver File Contents (Rl2000a_pci.zip)

Driver Package File Name: Rl2000a_pci.zip
File Size: 736.3 KB

            ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
            º                                                  º
            º        Compex RL2000 PCI Ethernet Adapter        º
            º  Copyright (C) 1997 by PDS. All Rights Reserved. º
            º                                                  º
            ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ GENERAL INFORMATION ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
 1) DOS and OS/2 NDIS v2.01 device driver
    RL2000.DOS v1.10 and RL2000.OS2 v1.10

     The NDIS drivers v1.10 for OS/2 and DOS were written to
     and tested with the Network Driver Interface Specification (NDIS)
     Version 2.0.1.

 The file layout in the MSLANMAN.DOS and MSLANMAN>OS2 directories is
 shown below:-


  MSLANMAN.DOS
     ³
     ÀÄÄ DRIVERS
            ³
            ÃÄÄÄ ETHERNET
            ³       ³
            ³       ÀÄÄÄ RL2000
            ³               ³
            ³               ÃÄÄ RL2000.DOS
            ³               ÀÄÄ PROTOCOL.INI
            ³
            ÀÄÄÄ NIF
                  ³
                  ÀÄÄÄÄÄ RL2000.NIF


  MSLANMAN.OS2
     ³
     ÀÄÄ DRIVERS
            ³
            ÃÄÄÄ ETHERNET
            ³       ³
            ³       ÀÄÄÄ RL2000
            ³               ³
            ³               ÃÄÄ RL2000.OS2
            ³               ÀÄÄ PROTOCOL.INI
            ³
            ÀÄÄÄ NIF
                  ³
                  ÀÄÄÄÄÄ RL2000.NIF

ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ INSTALLATION GUIDE  ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
 1) LAN Manager 2.0
 ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ

     a) Start the SETUP program.

     b) Choose "Actions" from the top manual bar.

     c) Choose "Import network drivers" to load the driver.
        Insert the driver diskette into a drive and enter correct
        source drive letter. Then SETUP will create the appropriate
        directory and transfer the driver from the diskette.

	After this step, the driver is loaded.  If you want to change the
	existing driver, then you should go through the following steps:

     d) Choose "View/Modify" from the top manual bar.

     e) Press [ENTER] until you find the "Network Drivers"
        manual. In this manual, you will find the existing
        network driver configuration and all network adapters and
        protocols which it supports.

     f) Remove the existing configuration by choosing
        "Remove".

     g) Select "Compex RL2000 PCI Ethernet Adapter" in the
        "Network adapter card" box and choose the appropriate protocol
        layer in the "Protocol" box.

     h) Choose "Add Driver" to add a hardware driver and "Add
        Protocol" to add a protocol driver to the "Network
        Configuration" box.

     i) Then choose "Done" to exit to the main manual. 

     j) Before exiting the SETUP program, choose "Save" from the
        "Actions" box to update the changes you have made.

 2) LAN Manager 2.1/2.2
 ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ

     The setup procedures for LAN Manager 2.1 is similar to LAN
     Manager 2.0.  Follow the procedure listed below to perform your
     installation.

     a) Start the SETUP program.

     b) Choose "Configuration" from the top manual bar.

     c) Choose "Network Drivers" to enter to the "Workstation
        Configuration" box.

     d) Choose "Add New Config" to check the existing network
        adapter drivers.

     e) Select "Other Driver" to import the driver from the
        diskette.

     Insert the driver diskette into a drive and enter correct 
     source drive letter. Then SETUP will create the appropriate 
     directory and transfer the driver from the diskette.

server: web1, load: 1.36