1. 3000cn_MR2a-update.exe Driver
2. 3000cn_readme.txt File Contents

3000cn_readme.txt Driver File Contents (3000cn_MR2a-update.exe)

Updating 3000cn Firmware.

!! IMPORTANT  NOTICE !!
* This is the MR2a update and contains ONE update for the ESS module.
* DO NOT apply this update unless all the files contained in 3000cn_MR2_update.exe have been applied FIRST.


Downloading and extraction:
1. Download the file "3000cn_MR2a_update.exe" from the Dell Support Website and save it to your hard drive. Suggest selecting the "Desktop" as the "Save-to" location for ease of finding the file after the download has completed.
2. After the download has completed, locate and double-click the file "3000cn_MR2a_update.exe" to begin the file extraction process.
3. The self-extractor opens, it is suggested the default "Unzip to folder" remain as provided; click "Unzip".
4. After the files extract, another window will indicate that "7 file(s) unzipped successfully"; click OK; then click "Close"
5. On the system desktop, locate the folder "3000cn_MR2a_update" and double-click to open. There should be three items:
	* readme.txt (this file)
	* readme.doc
	* 01_3000cn_ESS_MR2a sub-folder


Confirming current printer firmware revisions:
1. At the printer control panel, press the MENU button.
2. Press the down arrow until CONFIGURE is displayed; press the SET button.
3. Press the down arrow until REPORTS is displayed; press the SET button to display PRINTER SETTINGS.
4. Press the SET button; The Printer Settings report should print. Depending on optional hardware installed in the printer, it may be 2 pages long.
5. Several items on this page will be updated by this firmware upgrade. It is recommended this page be dated and saved for future reference.


NOTE: This entire update procedure is based on the printer being connected to a Network and connected to the SAME SUBNET. If not connected to the same subnet, temporarily move the printer to the same subnet of the system running the update utility. If your printer is NOT connected to a Network, the USB or Parallel local connections may be used instead. If either of these local connections are used, the printer drivers will need to be installed using the local connection to the system before running the firmware updater.


IMPORTANT: After the entire update process has been completed, the "admin" password will be reset to the default "password" and the language will be set to English.


Running the Firmware Update Utility:
(Firmware package 01)
1. Open folder 01_3000cn_ESS_MR2a
2. Double-click the file dellfwup.exe to run the Update Utility
3. When the firmware update window opens, ensure the button for "Network" is selected; Click Next.
4. The next window will display the module name and firmware version of the update program. Example: "Module Name:Printer F/W(200504141610)". Also shown will be a list including the IP address and current firmware versions of the Network printers available on your network.  Compare the Module version to the Printer F/W version. If they match, the printer does not need the firmware update. Click the box to select only those printers that do not have firmware revisions that match the module version; click NEXT.

NOTE: Each time the update utility is started, even if you have already updated a printer, the status for all printers will always be shown as "Not Complete".

5. A new screen will indicate that data is being sent to the printer; The firmware update utility will show the status as "Updating"; then the LCD on the printer should display:
	* "Receiving... Port9100"
	* followed by "Writing... Port9100"
	* followed by "Completed"
	* then the printer will reset and display the message "Diagnosing..."
	* followed by "Ready to Print" status.
6. The firmware update status should indicate "Complete"; click Next, then click Finish.
7. Close the folder 01_3000cn_ESS_MR2a


Confirming printer firmware revisions:
Once again, print a Printer Settings report to confirm the printer firmware revision. It is recommended these also be dated and saved for future reference.