1. PCMCIAV616.zip Driver
2. README.txt File Contents

README.txt Driver File Contents (PCMCIAV616.zip)

CardBus/PCMCIA driver Installation

Windows XP PCMCIA Installation Guide
1. Make sure that all cables are properly connected and the drive has power.
2. If you are using the Mobile drives, make sure that the power brick has a steady green light.
3. Boot your computer to Windows.
4. Plug in the PCMCIA cable to the Computer's PCMCIA Socket/Port.
5. Windows should now find a new hardware and install the default driver automatically.
6. If everything work out ok you should now see a CDROM icon from your windows explorer.


8. PCMCIA IDE/ATAPI Controller will be the default driver that Windows XP will load. Under DVD/CD-ROM drives, you should see an additional device.
9. If for some reason you did not see an additional device or your device manager,follow the Addonics Drivers installation below:
10. Go to start, settings, control Panel, Double click on system, go to hardware tab, device manager, go to IDE/ATA controller, Double click on the PCMCIA IDE/ATAPI Controller.
11. Go to the DRIVER tab then click on UPDATE DRIVER.
12. Click the second radio button or select the ADVANCED button then click Next.
13. Select the "Don't Search. I will Choose the driver to install" option then click Next.
14. Click on the HAVE DISK button to continue.
15. Click browse to locate the DRIVER FILES.
16. Browse to the Floppy Drive then open the win2000 folder.
17. Select the Addonics PCMCIA.......then click NEXT.
18. Click the "Continue Anyway" to proceed.
19. Let the OS install the Driver and that's it.
Click Finish.
20. Click YES to restart the Computer if prompted and that's it.

 For Windows 95, 98, SE and ME
 (Do not run the SETUP program from the driver disk, SETUP is for DOS or WIN 3.1 only) 
1. Power on your system and wait for the Desktop screen.
2.   Connect the CardBus/PCMCIA cable and external AC/DC adapter into the back of your Drive.
3. Plug the CardBus/PCMCIA card end of the cable into the PCMCIA slot on the side of your computer.
4. The system will automatically identify the new card and ask to load the driver.
 5.   Insert the driver diskette in “A” drive and follow the instruction on the screen to load “Addonics Cardbus IDE Controller” or  “Addonics PCMCIA IDE Controller”. All drivers and necessary files are located in the driver diskette under the sub-directory WINDOW9x. Be sure to select the A:/window 9x folder when the system prompts for the location of driver disk. 
6.   When finished installation, a PCMCIA card icon will appear in the lower right-hand of the Window’s Task Bar. 
7.    Double Click on the “My Computer” icon. Your Mobile CDRW will appear as a CD drive icon. You are now ready to use the drive.    
PCMCIA Installation for Windows NT 
1. Go to Start\Settings\Control Panel
2.   Double Click SCSI adapter icon
3. Click on the Driver Tab
4. Click Add to add new driver 
5.  Follow wizard and browse to A:\NT folder for the Driver.
6. Select “Addonics PCMCIA…” then click ok.
7.  Windows will prompt you for driver location again, to continue
     Type in A:\NT then click continue.
8. Click YES to restart your computer. Note: You must insert the PCMCIA cable when system is off.
  
  CardBus/PCMCIA Installation for Windows 2000
1.Make sure your computer is up and running
2.Verify that all cables are connected and there is power to the drive.
3.Insert the CardBus/PCMCIA cable to the PCMCIA socket.
4.A "New Hardware Found" message shall pops up.
5.Select "Next" to continue installation.
6.Select "Search for a suitable driver...." button and select "Next".

7.In "select a Device Driver page", select "Have Disk" to specify location. Enter path like A:\win2000" Select "Addonics CardBus…. or Addonics PCMCIA...." click YES for the Windows warning message and let Win2000 to finish the Installation and that's it.
8.   Double Click on the “My Computer” icon. Your drive 
Will appear as a CD drive icon. You are now ready to use the
CDRW drive.   


For Sony and Sharp Notebook users Alternative installation procedure
 
If you encountered system locked up using our standard installation procedures
(Most common with Window 98 SE, Sharp and Sony Notebook computers and computers with Ricoh Cardbus/PCMCIA Controller) please try to reinstall using the procedures outlined below:
   
1. Before installing the CardBus driver, make sure the CardBus is not
   Inserted into the PC Card slot.
2. Boot up the system and insert the CardBus driver diskette into Floppy Drive A
3. Click on the START button, then Settings and open the Control Panel
4. Click on the ADD NEW HARDWARE icon
5. Click NEXT and NEXT again, the screen will say Windows Will Now Search FOR PNP DEVICES, DO YOU WANT     WINDOWS TO SEARCH
6. Choose NO, I WANT TO SELECT THE HARDWARE FROM A LIST
7. Click NEXT
8. Select HARD DISK CONTROLLERS from the hardware list9. Click NEXT, and then click HAVE DISK
10.Type A:\Window9x, then click OK
11.Highlight ADDONICS CARDBUS IDE CONTROLLER, then click FINISH.
12.Shut down the system. Reboot the system with the CardBus inserted Inside the PC CARD slot. Make sure the     DVD drive is connected to the Other end of the CardBUS cable and the Drive is powered on.
13.The initialization of the DVD drive may take up to 40 seconds. During this time, mouse moving may be      sluggish.After completing the Initialization, a new CD ROM drive icon should appear in the My Computer. You      are now ready to use the DVD drive to install the Power DVD MPEG II decoding software.